Need a Carpenter in Hobart?

Tell us the suburb, roughly when the house was built, what needs repairing or building, the timber you have now, how high any deck will sit above the ground and whether the property is heritage listed or close to bushland. We will connect you with Hobart carpenters and licensed builders who quote against the same details, so the prices can be compared fairly.

Get Free Carpentry Quotes

Hobart Carpentry Prices, 2027 Estimates

Carpenter hourly rate, normal hours$65 - $95
Day rate on longer jobs$500 - $750
Door hung in an existing frame$150 - $400
Sticking door planed and rehung$80 - $180
Sash cords replaced, per window$150 - $300
Rotten window frame repaired$200 - $600
Weatherboard replaced, per metre$60 - $120
Hardwood deck, per square metre$450 - $850
Open timber pergola$3,500 - $8,000
Basic built-in wardrobe$1,800 - $3,500

Prices shown here are 2027 estimates for greater Hobart homes. Your quote depends on the age of the house and hidden rot, the timber species and finish, deck height on a sloping block, any heritage listing or bushfire attack level, and street access. It also depends on whether you need a licensed builder and a building surveyor, the official who certifies building work.

Hire a Carpenter Hobart TAS - Get Local Quotes

Carpentry in Hobart is shaped by the age of the houses and the slope of the land. Colonial era cottages in Battery Point, North Hobart and South Hobart still have sash windows, which slide up and down, timber floors and verandahs worth repairing rather than replacing. Post-war weatherboard homes in the northern suburbs and on the eastern shore now need decks, back steps, doors and rotten boards renewed. On hillside blocks, a new deck often ends up more than one metre above the ground at its outer edge, which changes who may build it and what paperwork is needed. Some homes sit inside a City of Hobart heritage precinct, a mapped area of protected older streets, or on the Tasmanian Heritage Register, so external timber work may need approval before it starts. Blocks near bushland on the city's edges can fall within a bushfire-prone area, where decking close to glass must meet stricter material rules. Tasmania has no separate carpenter licence, so the size and risk of each job decides whether a licensed builder must take responsibility. Older weatherboard homes also hide rot behind layers of paint, so many quotes carry an allowance for timber that only shows once boards come off. Steep steps and tight inner city parking add time wherever timber has to be carried in by hand. You will find 2027 estimates for common carpentry jobs across greater Hobart here, along with the local rules behind them. Post your job on The Quote Yard and we will connect you with Hobart carpenters and licensed builders who can quote on it.

What Hobart Carpenters Are Booked For

Most carpentry quotes in greater Hobart depend on the age of the timber, the height of any deck above sloping ground, and whether heritage or bushfire rules apply to the block. Include those details in your request so every carpenter who quotes is pricing the same work.

Get Free Quotes

At a Glance - Hobart Carpentry Prices, 2027 Estimates

Job Price Range How It Is Charged Hobart Factor Who Can Do It
Carpenter hourly rate $65 - $95 Hourly Steps and parking at older homes Carpenter
Day rate on longer jobs $500 - $750 Per day Unknowns in old framing Carpenter
Door hung in an existing frame $150 - $400 Fixed Openings no longer square Carpenter
Sticking door planed and rehung $80 - $180 Fixed Seasonal swelling Carpenter
Sash cords replaced $150 - $300 per window Fixed Painted-shut sashes Carpenter
Rotten window frame repaired $200 - $600 Fixed Matching old profiles Carpenter
Weatherboard replaced $60 - $120 per metre Per lineal metre Profile and species match Carpenter
Floorboard replaced $80 - $180 per board Per board Matching aged boards Carpenter
Floor joists replaced Priced on quote Fixed after site visit Subfloor access and damp Licensed builder
Low deck under one metre $450 - $850 per square metre Per square metre Hardwood species Carpenter or licensed builder
Deck one metre or more above ground Priced on quote Fixed after site visit Slope, footings and surveyor Licensed builder
Open timber pergola $3,500 - $8,000 Fixed Posts on sloping ground Carpenter or licensed builder
Straight timber staircase $3,500 - $7,000 Fixed Height and balustrade Licensed builder for structural work
Basic built-in wardrobe $1,800 - $3,500 Fixed Walls out of square Carpenter or joiner

Why Hobart Carpentry Quotes Differ

What is involved
You cannot see the condition of old timber until it is opened up. A rotten sill in a Battery Point cottage can turn out to be sound below the paint, or it can lead into a rotten stud that adds a day of work.
Slope sets the price of most outdoor carpentry in Hobart. A deck that sits just above the lawn on a flat Howrah block may stand three metres up on a hillside in Mount Stuart, with deeper footings, bracing and a building surveyor.
Heritage and bushfire rules change the materials as well as the method. Matching an original profile in a heritage precinct, or using fire resistant decking near glass on a bushfire-prone block, costs more than standard stock.
The building category, the risk group the law gives each job, decides who signs off. Low risk repairs need no paperwork, while notifiable work, which council must be told about before it starts, needs a licensed builder and a building surveyor, whose fees are passed on.
When comparing Hobart carpentry quotes, check for the named timber species and treatment, a written allowance for hidden rot, the deck height and building category for outdoor work, and a builder licence number where needed.

Before You Call a Hobart Carpenter

Note the suburb and roughly when the house was built, photograph the damaged timber and the trim around it, and measure how high any deck will sit at the lowest point of the ground below. Check whether the property is heritage listed or inside a heritage precinct, and whether the block is in a bushfire-prone area. If you know the timber species or weatherboard profile, include it.

Get Free Quotes
Free · No obligation · TAS-wide

Why Two Hobart Carpentry Quotes Rarely Match

Hobart carpenters typically charge $65 to $95 an hour, and many quote a day rate of $500 to $750 on longer jobs, as 2027 estimates. The rate is only a starting point, because the age of the house and the access decide how many hours a job really takes. Hanging a door in a 2000s Kingston home may be a morning's work, while the same door in an 1880s cottage may need a frame planed to suit walls that are no longer square. For a useful baseline on each common job, compare statewide figures for carpentry services in Tasmania. Two quotes for the same job usually differ because each carpenter expects to find something different once old timber is opened up.

Three questions help sort a Hobart carpentry job before you pick up the phone. First, is it a like-for-like repair, such as replacing a rotten weatherboard with one of the same profile, meaning the same shape, or does it change the structure or materials? Second, is the property heritage listed, inside a heritage precinct or within a bushfire-prone area? Third, will any finished deck, porch or platform sit one metre or more above the ground below it? The answers decide whether a carpenter can work alone, whether a licensed builder must take responsibility and whether a building surveyor has to be involved.

Most Hobart carpentry bookings fall into a handful of familiar groups. Repairs to doors, windows, floors and weatherboards in older homes make up a large share of the work. Decks, stairs and pergolas are common on sloping blocks, where flat outdoor space is hard to find. Built-in wardrobes and other joinery are the main interior jobs in the newer estates.

Carpentry Prices for Common Hobart Jobs

These are the carpentry jobs Hobart households book most often, with 2027 estimates drawn from current Tasmanian price ranges. The figures assume normal working hours, reasonable access from the street and timber that proves sound once the old surface comes off. Homes reached by long flights of steps, decks on steep ground and repairs to original heritage timber tend to sit at the top of each range. Treat each range as a way to judge a quote rather than as a fixed price.

Several common jobs are easier to judge with a little background. A door that sticks every winter and swings freely each summer is usually reacting to moisture, and planing the edge and sealing it often fixes the problem for $80 to $180. Rot at the bottom of a weatherboard or window frame can often be cut out and replaced with a matching piece, which keeps the original profile in place. To see when a repair is enough and when replacement makes better sense, read our timber repairs and door repairs guides. Ask for the timber species and profile to be named on the quote so that new pieces match the old ones.

Job 2027 Estimate Charging Method What Changes the Price
Hourly rate, weekdays $65 - $95 Hourly Experience and travel
Day rate on longer jobs $500 - $750 Per day Crew size and access
Door hung in an existing frame $150 - $400 Fixed Out of square openings
Door frame repaired $180 - $450 Fixed Depth of rot and mouldings
Hinges replaced, full set $120 - $250 Fixed Door weight and hinge type
Weatherboard replaced $60 - $120 per metre Per lineal metre Profile matching
Minor rot repaired $150 - $400 Fixed How far the rot has spread
Subfloor repaired $80 - $200 per square metre Per square metre Crawl space under the house
Deck boards replaced $80 - $180 per square metre Per square metre Condition of joists below
Deck stairs $120 - $250 per step Per step Stair side boards and landing
Timber balustrade on a deck $180 - $350 per metre Per lineal metre Infill style and posts
Timber handrail only $80 - $180 per metre Per lineal metre Fixing into old walls
Walk-in robe fit-out $3,500 - $12,000 Fixed Size and internal layout

Hourly, Day Rate or Fixed Price

Hobart carpenters price work in three main ways, and knowing which one applies avoids surprises at the end. Repairs where the cause is obvious, like hanging a door or replacing a few boards, are usually quoted at a fixed price after a quick look. Investigative work, such as finding out why a floor bounces or why a window frame keeps getting wet, is normally charged by the hour with an agreed maximum. Larger projects, such as a deck, a staircase or a run of wardrobes, should carry a fixed price and a written list of the work included. Day rates suit work that can only be judged as it goes, such as repairing an old verandah where each post may be different. Ask which method a carpenter is using before you agree to anything.

Materials are where carpentry quotes vary most from one business to the next. Some carpenters include timber, fixings and finishes, while others quote labour only and add materials at cost or with a margin. Hardwood decking, treated pine framing and factory-made laminated beams can change in price between the quote and the start date, so ask how long the materials price holds. Rubbish removal, skip hire and making good after the work, such as patching paint around a new frame, should each be stated. A quote that bundles everything into one figure is hard to compare with one that lists each part separately.

Some jobs need two people, and that shows up in the labour line. Long beams, the heavy hardwood side boards of a staircase and large wardrobe panels are hard for one carpenter to lift and fix safely. On a hillside block, a second worker may spend much of the day carrying timber down a side path or up a flight of steps. Ask whether the quote allows for a labourer or apprentice, and for how many days. A higher daily figure for a two-person crew can still cost less overall if the job finishes sooner.

Reading a Hobart Carpentry Quote

$500 to $750 a day for a carpenter on longer jobs, as a 2027 estimate
Line on the quote
What it should tell you
Labour
Hours or days, and the rate charged
Timber
Species, grade and treatment named
Fixings and hardware
Brackets, screws and door furniture by brand
Removal and making good
Old timber taken away and surfaces patched

A quote that names the timber species and treatment makes it easy to check what is delivered to site.

Ask whether the price is fixed or an estimate, and what happens to it if rot or hidden damage is found once boards come off.

Hobart Housing Stock and the Carpentry It Needs

The inner suburbs hold the oldest building timber in the city. Battery Point, North Hobart, West Hobart and South Hobart have Georgian and later nineteenth century cottages, terraces and villas with sash windows, panelled doors, timber floors and verandahs. Repairs here usually mean matching old profiles and species rather than fitting standard modern stock from a timber yard. New Town, Lenah Valley and Sandy Bay add Federation and inter-war homes, many of them weatherboard on timber stumps or brick piers. Houses in these suburbs often carry several generations of additions at the back, each built to a different standard.

Post-war homes fill much of the northern suburbs between Moonah, Glenorchy and Claremont, and large parts of the eastern shore around Bellerive, Lindisfarne and Howrah. Many are weatherboard or brick veneer houses now old enough for their decks, back steps and window frames to need replacing. Kingston, Blackmans Bay and the newer estates around Brighton and Sorell have younger homes, where wardrobes, doors and new decks are the usual jobs. Semi-rural blocks around Fern Tree, Tolmans Hill, Sandford and Margate more often border bushland. That can mean stricter bushfire building rules for new decks and additions, set out in the bushfire section further down. Tell each carpenter which group your home falls into so they arrive with the right expectations.

Area Example Suburbs Common Carpentry Work What Adds Cost
Inner city Battery Point, North Hobart, West Hobart, South Hobart Sash windows, floors, verandahs, period joinery Matching profiles and heritage approval
Older middle suburbs New Town, Lenah Valley, Sandy Bay, Mount Stuart Additions, stairs, decks on slopes Steep access and deck height
Northern suburbs Moonah, Glenorchy, Montrose, Claremont Rotten decks, back steps, doors Hidden rot in post-war framing
Eastern shore Bellerive, Lindisfarne, Howrah, Rokeby Decks, pergolas, window frames Exposed sites and older additions
Southern growth areas Kingston, Blackmans Bay, Brighton, Sorell Wardrobes, doors, new decks Travel and joinery lead times
Bushland edges Fern Tree, Tolmans Hill, Sandford, Margate Decks and additions near bush Bushfire attack level requirements

Low Risk, Notifiable or Builder Only: Sorting Carpentry Jobs

Tasmania does not license carpenters as a separate trade, so the job itself decides who may do it. Under the Building Act 2016, a Director's Determination, which is a formal ruling by the Director of Building Control, sorts building work into categories by risk and lists which jobs fall into each one. Category 1 low risk work, such as like-for-like repairs and low decks, may be done by the owner, a competent person with the skills and experience for that job, or a licensed builder. Category 2 work must generally be done by a licensed builder, though a few items also allow a competent person. Category 3 is notifiable work, which council must be told about first, done by a licensed builder once a building surveyor issues a Certificate of Likely Compliance, written confirmation that the plans meet the rules.

Builder licences in Tasmania are issued in classes, and the Builder (General Construction) class has a Domestic subclass, which covers building work on houses and outbuildings such as sheds. A carpenter without a builder licence can still do a great deal of useful work, including repairs, trim, doors, wardrobes and decks below the height limit. Once a job moves into Category 2 or 3, ask who holds the builder licence and whose name will go on the paperwork. The categories sit under the Building Act on the Tasmanian legislation website, and licence classes are explained by Consumer, Building and Occupational Services. Many Hobart carpenters hold a builder licence themselves, while others work under a licensed builder on the larger jobs.

Owners can take on some of this work themselves, within limits. Consumer, Building and Occupational Services says owners can build small structures no bigger than 18 square metres without a permit. Larger owner projects generally need an owner builder permit, which carries much of the same responsibility as a licensed builder. Licensed builders must also hold public liability insurance, which pays if their work injures someone or damages property, of at least $5 million, so ask to see the certificate before a larger job starts. A carpenter working as a subcontractor should be covered by their own policy or by the builder who engaged them. Check the scope of any builder licence on the Occupational Licensing portal before you sign a contract.

Example Job Usual Category Who Can Do It Paperwork
Like-for-like repair of boards, windows or doors Category 1 Anyone competent, including the owner No notice
Non-roofed deck with its floor under 1 m high Category 1 Anyone competent, including the owner No notice
Open pergola up to 36 square metres Category 1 Anyone competent, including the owner No notice
Roofed porch up to 9 square metres Category 1 Anyone competent, including the owner Council notified
Timber deck boards swapped for composite Category 2 Licensed builder or competent person No notice
Work on interior walls that carry no weight from above Category 2 Licensed builder No notice
Floor joists replaced after surveyor assessment Category 2 Licensed builder Council notified
Deck with its floor 1 m or more above ground Category 3 Licensed builder Building surveyor certificate first

Decks Above and Below One Metre on Sloping Blocks

The one metre line matters more in Hobart than in most flatter cities. Under the Director's Determination, a non-roofed deck whose floor is less than one metre above the surface below is low risk work that needs no notice to council. On a sloping block, a deck that starts at ground level by the back door can easily stand two or three metres up at its outer edge. Where the deck floor is one metre or more above the ground, the job becomes notifiable work for a licensed builder and a building surveyor. Measure the height at the lowest point of the ground under the deck, not at the doorway.

Higher decks carry costs that a low deck does not have. Footings on a Hobart hillside may need to reach rock or firm clay, and posts on a steep site take longer to set out, brace and level. Surveyor fees and the time spent preparing drawings are part of the price, and timber sizes must suit the span and height. Balustrades, which are the protective barriers along the open edges, add $180 to $350 a metre in timber. For more on materials, stair layouts and balustrade styles, see our deck builder and staircase builder guides.

Changing materials on an existing deck has its own category. Replacing timber decking with composite boards, which blend wood fibre and plastic, is listed as Category 2 work, which a licensed builder or a competent person may do, with no council notice. Timber decks in Hobart need regular oiling or staining to keep moisture out of the boards through the wet months. Intergrain makes decking oils, timber stains and floor finishes. Cabot's makes decking oils and stains, including its Aquadeck range. Feast Watson makes timber oils, varnishes and deck stains for exposed outdoor timber.

What Deck Height Changes

Deck height
What usually follows
Floor under 1 m at every point
Low risk, no council notice for a non-roofed deck
Floor 1 m or more at any point
Notifiable work with a building surveyor
Roof added over the deck
Check the porch, veranda or enclosure limits
Detached deck or boardwalk under 1 m
Low risk, but the council is notified

Hardwood decks cost about $450 to $850 a square metre and composite decks about $500 to $900, as 2027 estimates.

Ask the builder to measure deck height at the lowest ground point and to confirm the category in writing before you sign.

Pergolas, Porches and Enclosed Verandahs

Pergolas are among the simplest outdoor structures to get approved in Tasmania, provided they stay inside set limits. A free-standing garden pergola of up to 36 square metres and 3.5 metres high is low risk if it is left uncovered or has a permeable roof such as shade cloth. Add a solid roof of polycarbonate or steel sheeting and the structure is assessed differently, so confirm the category before choosing the roof. An open timber pergola usually costs $3,500 to $8,000, a polycarbonate covered one $5,500 to $12,000 and one with a steel roof $6,500 to $15,000. You can compare these roof types, posts and footings in our pergola builder guide.

Roofed porches and verandahs come with their own limits. A roofed porch or veranda with up to 9 square metres of floor, sitting no more than one metre high, is low risk but the council must be told. Shade structures, awnings and canopies up to 18 square metres are low risk with no notice required. Enclosing an existing deck, veranda or pergola with walls or glazing is Category 2 work for a licensed builder. In a heritage precinct, any of these changes at the front of a house may also need planning approval from the council.

Outdoor Structure Limits at a Glance

Structure
Low risk limit
Free-standing pergola
Up to 36 m2 and 3.5 m high, open or permeable roof
Roofed porch or veranda
Up to 9 m2 of floor, floor up to 1 m, council notified
Awning or shade structure
Up to 18 m2
Enclosing a deck or veranda
Category 2, licensed builder

These limits come from the Director's Determination and assume none of its standard limitations, the site conditions that remove low risk status, such as hazard areas or nearby drains, apply.

A site in a hazard area, land the planning maps show as at risk of bushfire or landslip, or work within one metre of a drain, may lose its low risk status.

Heritage Listings, Precincts and Period Joinery

Many Hobart homes are heritage listed or sit within a Heritage Precinct under the Tasmanian Planning Scheme - Hobart. The City of Hobart says owners usually need planning approval for any use or development of a heritage listed site or a site in a precinct. Some properties are also on the Tasmanian Heritage Register, which records places of state significance, and work on those is referred to the Tasmanian Heritage Council. Check the listing on the City of Hobart website before you ask for quotes, so carpenters know what they are pricing.

Heritage Tasmania can issue a minor works approval, a simpler sign-off, for work on a Register place that does not harm what makes it historically important. These approvals were called Certificates of Exemption before 1 January 2025, and older certificates remain valid. A minor works approval does not replace council planning approval, so a project may need both. Owners in the City of Hobart can apply online through PlanBuild Tasmania, the state planning and building portal, and Heritage Tasmania advisers give free advice on 1300 850 332. Larger projects that often follow, such as restoring a full verandah, are covered in our heritage renovations guide. Carpenters who regularly work on period homes can usually tell you early which parts of a job are likely to need approval.

Matching period joinery often means making parts rather than buying them off the shelf. A carpenter may need a specially shaped cutter to copy an old architrave, the moulding around a door or window, or a skirting or weatherboard profile, which adds a setup cost to short runs. Keeping a short offcut of the original profile lets the workshop copy it exactly. Salvaged timber from the same house, such as boards removed for a new doorway, is often the closest match for colour and grain. Ask whether the quote includes making profiles or relies on the nearest standard shape.

Situation Who Decides What the Job Needs What to Ask
External change in a heritage precinct City of Hobart Planning approval before work Has the permit been granted?
Place on the Tasmanian Heritage Register Tasmanian Heritage Council Permit or minor works approval Which approval applies?
Maintenance using matching timber Check with council first Matching species and profile Is the repair exempt?
Original windows replaced with a new type Council, plus Heritage Council if listed Approval and matching details Will the design be accepted?
Rear addition or new deck Council and building surveyor Planning and building paperwork Who prepares the drawings?

Bushfire-Prone Blocks and Deck Materials

Greater Hobart has many homes close to bushland, from the foothills of kunanyi / Mount Wellington to the rural edges of Kingborough and Clarence. Land in a bushfire-prone area is shown on a planning scheme overlay, and new homes and additions there need a bushfire hazard assessment. A bushfire hazard assessor accredited under Part 4A of the Fire Service Act 1979 prepares it, giving the site a bushfire attack level, or BAL, under AS 3959, the national bushfire building standard. The BAL sets the materials and details a builder must use for decks, subfloors, meaning the framing under a raised floor, windows, doors and other exposed parts of the building. Your council can confirm whether your block is inside the overlay before you ask for quotes.

Decks are one of the details most affected by the BAL. At BAL-12.5, the lowest level with extra building rules, decking within 300 millimetres horizontally and 400 millimetres vertically of any window or glass door must be non-combustible or fire resistant. Some hardwoods, including spotted gum, blackbutt and silvertop ash, are listed as bushfire resisting species, while other timbers suit areas further from the glass. ModWood makes composite decking, including a Flame Shield range, so ask whether any product has been tested for the BAL on your site. Advice on preparing a home and its surrounds is published by the Tasmania Fire Service.

Being in a natural hazard area can also change the category of a job. The Director's Determination lists bushfire, landslip, flooding and coastal hazards among its standard limitations, so work that is normally low risk may need more paperwork there. New houses and additions in the higher attack levels, BAL-40 and the Flame Zone, fall outside the usual notifiable work pathway. Ask the builder to check the hazard maps for your property early, before drawings are prepared and prices are fixed.

Bushfire Paperwork for Decks and Additions

BAL the bushfire attack level set for the site under AS 3959
Item
What it means
Bushfire-prone area overlay
Planning map showing where the rules apply
Accredited person
Bushfire hazard assessor who prepares the assessment
Bushfire attack level
Sets the construction details for the work
Building surveyor
Checks the work matches the assessment

Ask for the BAL to be stated on the quote, because two decks of the same size can need very different materials.

Do not swap materials on a bushfire-prone block without checking the assessment, since a cheaper board may not be allowed near glass.

Sash Windows, Doors and Draughts in Old Houses

Timber sash windows, which slide up and down on cords and counterweights, are common in Hobart's older homes, and most faults can be repaired rather than replaced. Typical problems include broken sash cords, the ropes joining each sash to its hidden weights, painted-shut sashes, loose beads, the thin strips holding each sash in place, and rotten sills. Replacing the cords on one window usually costs $150 to $300, while cutting out a rotten sill or frame and joining in new timber costs $200 to $600. Like-for-like replacement of windows and doors for maintenance, using the same or similar materials, is low risk work that needs no paperwork.

Doors in old houses often stick because the frame has moved through a century of wet winters and dry summers. Planing, rehanging and adjusting the hinges usually costs $80 to $180, while a new set of hinges costs $120 to $250. Corinthian makes entrance and interior doors, which helps where an original door is beyond repair and the opening suits a standard size. Gainsborough makes door handles, deadbolts and smart locks that can be fitted at the same visit. Glass and double glazing, which a glazier may handle alongside the carpenter, are covered in our window repairs guide.

Draughts are the most common complaint about old timber windows and doors in a Hobart winter. New weatherstripping around a sash costs about $60 to $150 a window, and around a door about $100 to $220. Good seals keep the original look of the window while cutting the cold air that leaks around loose sashes. Ask the carpenter to free any painted-shut sashes at the same visit, so every window can be opened for fresh air.

Problem Usual Fix 2027 Estimate Note
Sash will not stay open New sash cords $150 - $300 per window Weights stay in the box
Rotten sill or lower frame Cut out and splice new timber $200 - $600 Match the original species
Draughts around a sash New weatherstripping $60 - $150 per window Seals without changing the look
Draughts around a door New weatherstripping $100 - $220 Check the threshold too
Door sticks in winter Plane, rehang and seal $80 - $180 Seal the planed edge
Door frame split or rotten Frame repair $180 - $450 Architraves may need replacing
Lock or latch failing Repair or replace the lock $150 - $350 Name the hardware brand

Floors, Joists and Subfloor Repairs

Timber floors in older Hobart homes often outlast the joists and bearers underneath, the timber beams that hold the floor up. A floor that bounces, slopes or creaks loudly usually points to a problem in the subfloor, which is the framing under the boards. Damp under the house, failed stumps and poor earlier repairs are the usual causes. Replacing individual boards usually costs $80 to $180 a board, and subfloor repairs $80 to $200 a square metre.

The category matters once the structure itself is involved. Minor structural repairs assessed by a building surveyor, such as replacing floor joists, are Category 2 work for a licensed builder, and the council must be notified. Major structural repairs to a house fall into Category 3 and need a building surveyor's certificate before work starts. If a leak under the house is part of the problem, a Hobart plumber should fix it before new timber goes in. Patching, sanding and refinishing once the structure is sound again are covered in our floor repairs guide.

Matching old floorboards is one of the harder parts of the job. Boards in older homes were often milled to widths and thicknesses that are no longer standard stock. A carpenter may take matching boards from inside a wardrobe or under a fixed cupboard, then fit new boards in the hidden spot. Localised sanding and refinishing to blend the repair usually costs $60 to $100 a square metre. Ask how the carpenter plans to match colour and width before the old boards come up.

Signs Worth a Subfloor Check

Sign
Likely cause
Bouncy floor near an outside wall
Rotten bearer or joist end
Doors that suddenly start sticking
Movement in stumps or piers
Musty smell under the house
Poor ventilation or a hidden leak
Gaps opening along the skirting
Floor dropping on one side

Photos taken through the subfloor access hatch help a carpenter judge the job before the site visit.

Replacing stumps or piers is not covered by the simpler repair item, so ask a licensed builder how that work will be treated.

Built-in Wardrobes and Joinery Made Off Site

Built-in wardrobes are one of the most common carpentry jobs in Hobart's newer homes, and in older homes that never had them. A basic built-in wardrobe usually costs $1,800 to $3,500, a standard one $2,500 to $5,500 and a premium fit-out $4,500 to $8,000. Laminex makes board for cabinetry and wardrobes, which many joiners use for cabinet boxes and shelving. Blum makes hinges and drawer runners, and naming them on a quote shows the hardware quality you are paying for. In an old house, walls and floors are rarely square, so allow for scribing, which means shaping panels to fit uneven surfaces.

Joinery is usually built in a workshop and installed later, and that affects the deposit. Under Tasmania's residential building contract rules, a contract of $20,000 or more where off-site work makes up more than half the price can carry a deposit of up to 20 percent. That is higher than the usual deposit caps, the legal limits on what can be asked up front, so ask for the split between workshop and site work in writing. Wardrobe lighting needs a licensed electrician, so a Hobart electrician may be booked for the same week. Door types, internal layouts and finishes are compared in our wardrobe builder guide. Allow for the workshop lead time when planning around a move or a sale.

Item 2027 Estimate What Moves It Ask About
Basic built-in wardrobe $1,800 - $3,500 Width and shelving Board brand and edge finish
Standard built-in wardrobe $2,500 - $5,500 Drawers and doors Hinge and runner brand
Premium wardrobe fit-out $4,500 - $8,000 Finishes and lighting Whether an electrician is needed
Walk-in robe fit-out $3,500 - $12,000 Size and layout Workshop lead time
Sliding wardrobe door $350 - $800 per panel Mirror or board finish Track system and soft close

Asbestos Sheeting Behind Old Linings

Many older Hobart homes contain asbestos cement sheeting, often called fibro, behind later linings and finishes. It turns up in eaves, bathroom and laundry walls, external cladding and under old floor coverings. Carpenters often meet it when removing a wall lining, replacing eaves or cutting in a new window or door. WorkSafe Tasmania requires a licence to remove more than 10 square metres of non-friable asbestos, which is bonded sheeting that does not crumble by hand, or any amount of friable asbestos, which crumbles easily. Smaller areas of non-friable sheeting can be removed without a licence, but only in line with the code of practice on safe removal.

Ask any carpenter quoting on an older home how they will deal with suspect sheeting. A careful quote either excludes it and recommends testing first, or allows for removal by a licensed removalist where the area is large. Cutting, drilling or sanding suspect sheeting with power tools releases fibres, so work should stop until the material has been identified. Guidance is published by WorkSafe Tasmania and by the national asbestos and silica safety agency for householders and renovators.

Where Fibro Hides in Older Homes

Location
Job that often disturbs it
Eaves lining
New fascia boards, gutters or roof work
Bathroom and laundry walls
Renovations and new linings
External cladding
New windows or doors
Under old floor coverings
Floor repairs and new boards

Testing a small sample before work starts removes the guesswork about what the sheeting contains.

Do not let anyone cut, drill or sand suspect sheeting until it has been identified.

Urgent Make-Safe Carpentry

Some carpentry cannot wait for a normal booking. A smashed door or window after a break-in, a storm-damaged gate or a collapsed step leaves a home insecure or unsafe. A carpenter can usually board up an opening, refit a door or prop a damaged structure on the same day. After hours visits are priced on quote, so ask for the figure before anyone sets out.

Make-safe work, a quick temporary fix that secures the home, and the lasting repair are two separate stages. The first visit secures the home with plywood sheeting, temporary locks or props, while the lasting repair is quoted once the damage is clear. Photograph the damage before anything is moved and keep any broken parts, since insurers often ask to see both. If a glazier is needed for broken glass, the carpenter can usually prepare the frame so the glass goes in at one visit. A written note of what was done on the first visit makes an insurance claim easier to support.

Collapsed steps and rotten deck boards are a common urgent call at older Hobart homes. Block off the damaged area before the carpenter arrives, because a second board often fails close to the first. Replacing deck boards usually costs $80 to $180 a square metre, though rot in the joists below can add to that. Where the deck is high or fixed to the house, ask whether the frame needs checking by a licensed builder. Rusted bolts and loose brackets where the deck meets the house deserve particular attention. Replacing one board at a time on a deck with widespread rot rarely saves money in the end.

Plenty of jobs look urgent but can safely wait for a weekday booking. A sticking door, a draughty window or a loose skirting board will cost less to fix in normal hours. Booking several small jobs into one visit, such as rehanging a door, replacing a few boards and fixing a gate latch, spreads the cost of the first hour. A local carpenter who knows older houses can often finish a list like that in a single day. Once the work is done, a Hobart cleaner can clear sawdust from floors, cupboards and window tracks.

Contracts, Cooling Off and Six-Year Warranties

Bigger carpentry jobs fall within the Residential Building Work Contracts and Dispute Resolution Act 2016 once the contract price reaches $20,000. The contract needs to be written down, dated and signed by you and the builder, and must show the contractor's licence number, a clear description of the work, the price and the expected completion date. Deposits are capped at 10 percent for contracts from $20,000 to $50,000 and 5 percent above that, apart from the off-site joinery case. A cooling-off period lets you withdraw within five business days of receiving the signed contract, plans, specifications and the consumer guide. If you do, the builder may keep $100 plus reasonable out-of-pocket costs.

These contracts carry statutory warranties, legal promises about the work's quality, lasting six years from practical completion, when the work is finished apart from minor items. When a fault appears, tell the builder promptly and confirm the complaint in writing with photographs. Next, a notice of dispute starts mediation, where an independent person helps both sides agree within 20 days, and unresolved matters can go to TASCAT, the state civil and administrative tribunal. Since 1 October 2026, the work of Consumer, Building and Occupational Services has been shared by two agencies, Consumer Affairs Tasmania and Building Standards Tasmania. Keep the contract, the consumer guide, invoices and any surveyor certificates together, since each body will ask to see them. Licences can be checked through the state's Occupational Licensing portal, and misleading advertising can be reported to the ACCC, the national consumer watchdog.

Rot found halfway through a job is the most common reason a carpentry price changes. A good contract says how hidden damage will be priced, such as a set rate per metre of weatherboard or per joist replaced. Agree each change in writing, with its price, before the extra work begins. Keep a running list of approved changes, because it lets you check the final invoice line by line and settle any disagreement about extras.

Concern First Step Next Step Keep Handy
Defective or incomplete carpentry Written notice to the builder Mediation notice, then TASCAT Contract, photos and invoices
Deposit above the legal cap Ask for the contract terms in writing Free regulator advice Contract and receipts
Builder not licensed for the work Occupational Licensing portal Building Standards Tasmania Business name and licence details
Heritage work done without approval City of Hobart Tasmanian Heritage Council Address and description of work
Misleading claims in an advert Raise it with the business ACCC Copy of the advert or quote

What to Look Out For in a Hobart Carpentry Quote

A strong Hobart carpentry quote names the timber species, grade and treatment, such as H3 treated pine, which is pine treated for outdoor use above ground. It lists connectors and fixings by brand, because cheap brackets corrode quickly on exposed decks. Pryda makes timber connectors, tie-downs and post anchors for decks and pergolas. Simpson Strong-Tie makes joist hangers, framing connectors and structural screws. For external timber, the quote should also name the finish and the number of coats.

Certain red flags turn up often in Hobart carpentry quotes. A deck quote on a sloping block that never mentions height, category or a building surveyor may be underpriced or non-compliant. A heritage repair quote that proposes replacing original windows with modern units, without mentioning approval, should be questioned. Be wary of anyone who asks for a deposit above the legal caps or will not put a licence number on a job of $20,000 or more. A quote far below the others has usually left out rot repairs, rubbish removal or making good. Asking each carpenter to price the same written list of exclusions shows up these gaps quickly.

Carpentry Quote Red Flags

What is involved
Builder licence number for Category 2 or 3 work.
The timber species, grade and treatment named in full.
Connectors, fixings and finishes named by brand and type.
Deck height and building category stated for outdoor work.
Heritage or bushfire requirements named where they apply.
An allowance for hidden rot and making good stated.

A phone price for rot nobody has looked at, which is only a guess.

A deposit above the legal cap on a contract of $20,000 or more.

Line up every quote and compare the inclusions first, then the prices. The lowest Hobart carpentry price usually skips the rot allowance, access costs or making good.

Getting Hobart Carpentry Quotes You Can Compare

Carpenters can only quote the same job when they all start from the same description. Write a short brief covering the suburb, the age and style of the house, the work needed and the timber you would like used. Add photographs of the damaged area, the trim around it and the view through any subfloor access hatch. Note whether the property is heritage listed, in a heritage precinct or in a bushfire-prone area, and give the deck height at its lowest point. With that information, every carpenter who quotes is pricing the same work rather than guessing.

For small repairs a couple of quotes will normally do, but decks, stairs and wardrobes deserve three. Check each quote's expiry date, the likely start date and which items could change after old timber is removed. Other trades often join a carpentry job, such as a Hobart bricklayer for brick piers or the statewide carpentry services directory for specialists. Brief every trade at the same time so the work happens in the right order.

Weatherboard and cladding repairs are easier to quote when the existing product is known. James Hardie makes fibre cement weatherboards such as Linea, which suit many post-war and newer homes. Weathertex makes weatherboards and panels from Australian hardwood. Hyne makes structural pine framing and glulam beams, made from layers of timber glued together, used in decks, pergolas and additions. Selleys makes Liquid Nails construction adhesive and No More Gaps filler, which often appear on trim and lining jobs. Keep every quote, photograph and approval together until the job is finished and paid for.

Carpenters Across Greater Hobart

Carpentry prices on this page apply across greater Hobart. Jobs close to the main centres rarely carry a travel charge, while semi-rural properties and outlying towns sometimes do.

▶ Hobart 30 areas
Hobart CBD Battery Point Sandy Bay South Hobart West Hobart North Hobart New Town Lenah Valley Mount Stuart Moonah Glenorchy Claremont Berriedale Rosetta Montrose Bellerive Howrah Lindisfarne Rosny Park Lauderdale Sandford Kingston Blackmans Bay Taroona Margate Brighton Bridgewater Sorell Richmond New Norfolk
▶ Launceston 26 areas
Launceston CBD East Launceston West Launceston South Launceston Newstead Norwood Kings Meadows Youngtown Prospect Riverside Trevallyn Summerhill Legana Grindelwald Exeter Beaconsfield Beauty Point Rosevears Hadspen Carrick Longford Perth Evandale Scottsdale Lilydale George Town
▶ Devonport & Burnie 26 areas
Devonport East Devonport Spreyton Miandetta Latrobe Port Sorell Shearwater Hawley Beach Ulverstone Turners Beach Penguin Burnie Somerset Wynyard Boat Harbour Sisters Beach Stanley Smithton Wivenhoe Cooee Park Grove Montello Sheffield Railton Westbury Deloraine
▶ Huon Valley 22 areas
Huonville Ranelagh Franklin Port Huon Geeveston Dover Southport Cygnet Lymington Gardners Bay Woodbridge Middleton Snug Kettering Bruny Island Alonnah Grove Glen Huon Judbury Lower Longley Leslie Vale Pelverata
▶ East Coast 22 areas
St Helens Scamander Beaumaris Binalong Bay Stieglitz Pyengana Fingal Mathinna Bicheno Coles Bay Swansea Orford Triabunna Maria Island Buckland Dolphin Sands Cranbrook Apslawn Seymour Falmouth Four Mile Creek Gray

Hobart Carpenter FAQ

Is an hourly rate or a day rate better for Hobart carpentry?
Hourly rates suit small or uncertain jobs, while a day rate suits longer work such as decks or verandah repairs. As 2027 estimates, Hobart carpenters typically charge $65 to $95 an hour or $500 to $750 a day. Small jobs are often quoted at a fixed price instead, such as $150 to $400 to hang a door in an existing frame. Access up steps, hidden rot and the timber species usually matter more than which rate is used.
Does a deck on my sloping Hobart block need a building surveyor?
It depends on the height of the deck floor above the ground below it. A non-roofed deck whose floor is less than one metre above the surface is low risk work with no council notice. Where the floor is one metre or more above the ground, the deck is generally notifiable work for a licensed builder. A building surveyor must then issue a Certificate of Likely Compliance before work starts.
Can I put up a pergola in Hobart without telling the council?
A free-standing pergola of up to 36 square metres and 3.5 metres high is low risk work with no council notice. It must be left uncovered or have a permeable roof such as shade cloth. A solid roof of polycarbonate or steel changes how the structure is assessed. Heritage precincts and mapped hazard areas can also change the answer, so check with the council first.
Can the old sash windows in my Hobart cottage be repaired?
Most sash windows can be repaired, and like-for-like repairs for maintenance are low risk work that needs no paperwork. Replacing the sash cords usually costs $150 to $300 a window, as a 2027 estimate. Cutting out and splicing a rotten sill or frame usually costs $200 to $600. On a heritage listed home, replacing windows with a different type may need approval.
Who approves timber work on a heritage listed Hobart property?
The City of Hobart says owners usually need planning approval for development of a heritage listed site or a site in a heritage precinct. Work on a place on the Tasmanian Heritage Register also needs Heritage Council approval, either a permit or a minor works approval. A minor works approval does not replace council approval. Heritage Tasmania advisers can be called for free on 1300 850 332.
What decking can be used near bushland around Hobart?
On a block in a bushfire-prone area, an accredited person sets a bushfire attack level under AS 3959. At BAL-12.5, decking within 300 millimetres horizontally and 400 millimetres vertically of windows or glass doors must be non-combustible or fire resistant. Hardwoods such as spotted gum, blackbutt and silvertop ash are listed as bushfire resisting species. Ask for the BAL and the decking product to be named on the quote.
Why can the deposit be higher for built-in wardrobes?
Under Tasmania's residential building contract rules, deposits on contracts of $20,000 or more are normally capped at 10 or 5 percent. Where off-site work makes up more than half of the contract price, the cap rises to 20 percent. Wardrobes and other joinery are often built in a workshop, so this can apply to larger joinery contracts. Ask for the split between workshop and site work in writing.
Who can replace rotten floor joists in Tasmania?
Replacing floor joists after assessment by a building surveyor is Category 2 work, which must be done by a licensed builder. The council must be notified of this work. Major structural repairs to a house fall into Category 3 and need a building surveyor's certificate before work begins. Subfloor repairs usually cost $80 to $200 a square metre, as a 2027 estimate.
What happens if asbestos sheeting turns up during a Hobart carpentry job?
Work should stop until the sheeting has been identified, because cutting, drilling or sanding it can release asbestos fibres. WorkSafe Tasmania requires a licence to remove more than 10 square metres of non-friable asbestos or any friable asbestos. Smaller areas can be removed without a licence, but only by following the code of practice. A careful quote either excludes suspect sheeting or allows for testing.
How long do I have to claim for faulty building work in Tasmania?
Work under a residential building contract of $20,000 or more carries statutory warranties of six years from practical completion. Raise any problem with the builder quickly and follow up in writing. If that fails, a notice of dispute starts mediation, which allows 20 days to reach agreement. Unresolved disputes can then go to the Tasmanian Civil and Administrative Tribunal.

Hobart Carpentry Specialists

For Trades & Contractors - TAS

Hobart carpentry jobs often run alongside other trades. Wardrobe lighting needs an electrician, subfloor leaks need a plumber, and brick piers and steps can involve a bricklayer. These are the services most often booked with carpentry in the capital.

Compare Hobart Carpentry Quotes

Tell us the suburb, the age of the house, the work needed and whether the block is sloping, heritage listed or near bushland, and compare quotes from Hobart carpenters and licensed builders who are all pricing the same scope.

Get Free Carpentry Quotes

About This Guide

This page provides guidance information only. Details may change, always verify with the relevant authorities and seek independent professional advice where needed.

Reviewed by The Quote Yard Editorial Team

Published 20 November 2026 ·

How The Quote Yard Works

We connect you with independent local tradies and service providers, we don't perform any trade work ourselves. Tradies provide their own quotes directly to you. Always confirm licensing, insurance, and scope of work before engaging any provider.

We service all regions including Hobart, Launceston, and regional areas. Verify licences at CBOS Tasmania.
Prices are 2027 estimates based on current Tasmanian carpentry rates applied to greater Hobart. Quotes move with the age of the house and the amount of hidden rot, the timber species, grade and finish, deck height above sloping ground, heritage listing or precinct controls, any bushfire attack level on the block, whether the work is low risk or needs a licensed builder and building surveyor, workshop joinery lead times, and access from the street. Compare written quotes that name the timber and fixings, state an allowance for hidden rot, give the building category for outdoor structures and show a builder licence number where one is required.
Need work done? Get free quotes. Post a Job – It's Free