Buying in Queensland?

Tell us the suburb, the age of the home and when your cooling-off period or inspection condition ends, and we will connect you with QBCC licensed plumbers for quotes.

Get Free Plumber Quotes

Typical Costs (2027 Estimates)

Call-out and first hour$120-$250
Each extra hour (normal hours)$95-$150/hr
Drain camera inspection with report$250-$550
Visual check and water meter test$150-$300
Acoustic leak detection$250-$500
Hot water relief valve replaced$150-$350
Whole-house plumbing inspectionPriced on quote

All figures are 2027 estimates for Queensland homes. Full inspections, repairs found on the day and regional travel are quoted for each property.

Pre-Purchase Plumbing Inspection Services QLD - Get Local Quotes

A pre-purchase plumbing inspection is a visit by a plumber licensed by the QBCC, the state building regulator, to test the water pipes, drains, fixtures and hot water of a Queensland home before you are bound to buy it. The standard Queensland contract gives buyers a cooling-off period, five business days in which they can still pull out, and auctions have none. Book fast, or add a contract condition letting you end the sale over a poor report. A building and pest inspection looks for obvious defects and termites, but it does not film the sewer, test the meter for hidden leaks or check the valves on a hot water unit. The plumber does those tests, runs every tap, shower and toilet, and writes up the results in a report with photos. Filming the sewer and stormwater lines can reveal roots, cracks and sagging joints that would become your repair bill after settlement, when the sale completes. Acreage homes may also need a check of the septic tank or home sewage treatment plant and any rainwater tank pump. Older homes and bathrooms renovated without paperwork need the closest look. Since August 2025, sellers must give buyers a seller disclosure statement on title, planning and notices, but it says nothing about the pipes. Prices here are 2027 estimates, with a drain camera inspection and report at $250 to $550 and a call-out with the first hour at $120 to $250. Whole-house inspections have no published price, so plumbers quote each home. Book early, because the report and any repair quotes need to reach you before your deadline.

Plumbing Checks for Queensland Home Buyers

Licensed plumbers inspect houses, townhouses, units and acreage for buyers across Brisbane, the Gold Coast, the Sunshine Coast, Ipswich, Logan, Toowoomba, Townsville, Cairns and regional towns. Post the job with your contract deadline and compare quotes from up to three plumbers who work near the property.

Get Free Quotes

At a Glance - Plumbing Checks for QLD Buyers (2027 Estimates)

Check 2027 Estimate (QLD) Useful When Carried Out By Result
Whole-house plumbing inspection Priced on quote Older homes or recent bathroom renovations QBCC licensed plumber Written report with photos
Drain camera inspection with report $250-$550 Large trees, slow drains or old sewer lines QBCC licensed plumber or drainer Footage with distances to faults
Visual check and water meter test $150-$300 No obvious warning signs QBCC licensed plumber Leak or no leak at the meter
Acoustic leak detection $250-$500 Meter dials move with taps off QBCC licensed plumber Likely position of the leak
Full property leak audit $400-$1,000 Damp floors, stains or high water bills QBCC licensed plumber Several test methods combined
Call-out and first hour $120-$250 A quick check of one or two items QBCC licensed plumber Findings explained on site

Budget Notes for a QLD Plumbing Check

Quote Yard's Queensland price guides give no single figure for a full pre-purchase plumbing inspection, so plumbers quote each home. Labour starts with the call-out and first hour at $120 to $250, and each further hour in normal hours costs $95 to $150. Drain filming with a written report adds $250 to $550.

Leak testing is priced by method. A visual check with a meter test costs $150 to $300, acoustic detection, which listens for leaks, costs $250 to $500 and thermal imaging with a heat camera costs $300 to $600.

These are 2027 estimates for Queensland. Repairs found during the visit are quoted on their own.

How a Plumbing Check Fits a Queensland Home Purchase

A pre-purchase plumbing inspection is a booked visit where a QBCC licensed plumber tests the water, drainage and hot water systems of a home you are thinking of buying. The aim is to find faults that cost real money to fix, such as a cracked sewer line, a leaking water service or a hot water unit near the end of its life. The Queensland Building and Construction Commission, known as the QBCC, licenses plumbers and drainers, who work on underground drains, and also licenses the inspectors who carry out building inspections. For buyers with specific concerns, the QBCC suggests a more detailed report from an appropriate expert and names a plumber as one example. Filming the drains and reading the water meter are two tests that a building inspection leaves out.

Queensland homes vary widely in how their plumbing was built. Post-war timber houses in Brisbane may have pipes running under a raised floor, while newer homes on a concrete slab in Logan or the Sunshine Coast hide their pipes in concrete and wall cavities. Acreage blocks outside the sewered areas add septic tanks or home sewage treatment plants, and some coastal and rural homes have rainwater tanks with pumps. Local plumbers who know the area's homes can tell you which of these checks the address needs.

Part of the System Test on the Day Finding That Matters Next Step
Water meter Reading taken with every tap off Dials keep turning Leak detection visit
Sewer drain Camera pushed from an inspection opening Roots, broken joints, sags Clearing, relining or dig-up quote
Overflow relief gully Grate located and checked Buried, capped or blocked grate Uncover or raise it
Hot water unit Data plate, relief valve, tempering valve Rusty tank or dripping valve Valve or replacement quote
Toilets and cisterns Flush and refill test Water still running into the pan Cistern repair
Showers and wet areas Water run, grout and skirting checked Swollen skirting, hollow tiles Regrout or leak repair
Stormwater Downpipes and pits hosed Water pooling near the slab Stormwater clearing

Plumbing inside wall cavities, under a slab or below a driveway cannot be seen, so the plumber judges it from meter movement, damp patches and drain footage. Furniture, stored goods and locked rooms can also block access to taps, cupboards and inspection openings, the capped access points on drains. The seller or their agent must agree before the plumber lifts covers or removes access panels. Each inspection records the condition of the plumbing on one day, so it cannot promise how the system will behave later. Building inspections share this limit, and the QBCC says a building inspection is not a warranty against future defects. The written report should list every area that could not be checked.

As the buyer, you book the plumber, pay for the visit and receive the report. The seller's agent arranges access, and the seller must agree to any test that involves opening up the plumbing. No plumber can cut into walls or dig up paving during a pre-purchase check, so the plumber relies on tests that leave the home as it was. If a test suggests a hidden fault, the next step is a closer investigation with the seller's consent or after you own the property.

What a Plumbing Inspection Costs in QLD (2027 Estimates)

No Quote Yard price guide for Queensland lists a single figure for a whole-house pre-purchase plumbing inspection, so each plumber prices it on quote. The price depends on labour, the tests you choose and the time spent writing the report. Labour starts at $120 to $250 for the call-out and first hour on site, and extra time costs $95 to $150 an hour in normal hours. Filming the sewer and supplying a report adds $250 to $550. Every figure on this page is a 2027 estimate, and repairs found during the visit are quoted separately.

Leak testing comes in several levels of detail and price. For a home with no warning signs, a visual check with a water meter test costs $150 to $300. Acoustic leak detection, where the plumber listens to the pipes through sensitive microphones, costs $250 to $500. Thermal imaging, a camera that shows temperature differences that can reveal a hidden hot water leak, costs $300 to $600. Combining several methods in a full property leak audit costs $400 to $1,000. Start with the meter test, and pay for further tests only if it shows water moving.

Item 2027 Estimate (QLD) When It Applies
Call-out and first hour $120-$250 Every visit in normal hours
Each extra hour $95-$150/hr Larger homes and longer checks
After-hours or weekend call-out $180-$450 Access only outside business hours
Regional travel fee $60-$250 Properties outside the plumber's area
Drain camera inspection with report $250-$550 Sewer or stormwater filming
Visual check and meter test $150-$300 First step for hidden leaks
Acoustic leak detection $250-$500 Meter shows water moving
Thermal imaging $300-$600 Suspected hot water leak
Full property leak audit $400-$1,000 Several warning signs together
Whole-house plumbing inspection Priced on quote Full check with written report

These price ranges add up quickly, even for a short visit. Two hours on site costs $120 to $250 for the call-out and first hour, plus $95 to $150 for the second hour, giving $215 to $400. If the plumber charges drain filming as a separate item, adding $250 to $550 brings the range to $465 to $950. Plumbers can choose to include the first hour in the camera price, so compare the full quoted totals and not the separate parts. Properties outside the plumber's home area may also carry a travel fee of $60 to $250.

The time of day affects the price more than any single test. After-hours and weekend call-outs cost $180 to $450 before any work begins, with Sundays and public holidays at the top of that range. Weekday access is cheaper wherever the agent and seller can arrange it. Combining the drain camera, meter test and hot water check in one visit avoids paying a second call-out. Have each plumber list these items as separate lines so you can compare quotes line by line. Quotes that hide everything in one figure make it hard to tell what you are paying for.

Five Business Days: Fitting the Check Into Cooling-Off

The standard Queensland contract for buying a home comes with a cooling-off period of five business days, a window in which the buyer can still pull out, according to the Queensland Government. This period starts on the day you receive a copy of the contract signed by both the buyer and the seller. If that copy arrives on a weekend or public holiday, the count begins on the next business day. Ending the contract during cooling-off allows the seller to deduct a penalty of up to 0.25% of the purchase price. The seller must then return your deposit within 14 days.

Five business days is a short window to book a plumber, receive a report and collect repair quotes. Auction purchases carry no cooling-off period at all, so any plumbing check has to happen before you bid. There is also no cooling-off if you were a registered bidder and sign a contract within two business days after the auction fails to sell the property. Buyers can also waive or shorten cooling-off by giving written notice to the seller or their agent, which gives up this protection. For these reasons, a written inspection condition in the contract gives a buyer more certainty than relying on cooling-off alone.

In practice, the five days start once both parties have signed the contract and you hold a copy. Contact plumbers before that day if you can, so one is ready to attend within the first two or three business days. Request access times, keys and the location of the water meter and hot water unit from the agent early. Allow at least a day for the report to arrive and another for repair quotes on any serious fault. Those steps leave a little room to talk with the seller before cooling-off ends. If five days is not enough, ask your solicitor about a longer inspection condition before you sign.

Building and Pest Conditions and Where Plumbing Fits

Queensland contracts can include conditions, clauses that must be met before the sale goes ahead, such as finance approval, a building and pest inspection or the sale of your current home. The Queensland Government warns that a condition left out of the signed contract is not legally binding. Your solicitor or conveyancer can tell you whether the inspection condition can cover a plumbing report as well as the building and pest report. Agree on that wording before you sign, so you can act on the plumber's findings if problems appear.

The QBCC says only a licensed residential building inspector can complete a pre-purchase building inspection, and termite checks need a licensed pest controller. These inspectors look for obvious defects, including leaking ceilings, missing waterproofing and drainage problems, and they point out possible asbestos. They do not film sewer lines, run a meter leak test or test the valves on a hot water unit. Booking a plumber alongside the building inspection covers both the structure and the pipes. Give the plumber a copy of the building report so any stains or damp patches it mentions get a closer look.

What the Seller Disclosure Statement Says About Plumbing

Since 1 August 2025, Queensland sellers must give buyers a seller disclosure statement, known as Form 2, before the contract is signed. The rules come from the Property Law Act 2023, the Queensland law covering property sales and other land dealings. Form 2 covers title searches, encumbrances (rights others hold over the land), zoning, transport notices, resumption notices about the government acquiring land, and contamination registers. It also lists tree orders, heritage listings, whether there is a pool and any notices issued under building, planning and QBCC laws. Sellers must also attach certain certificates, such as a pool safety certificate where one applies and, for some unit complexes, a body corporate certificate from the owners' group.

Buyers have a remedy when the statement is missing or wrong. If the seller fails to follow these rules, even by accident, the buyer may be able to end the contract at any time up to settlement. For wrong or incomplete information, the buyer must show the problem was significant, that they did not know of it when signing and that they would not have signed had they known. The scheme does not apply to some sales, such as sales between related parties or to government bodies. Your solicitor can advise whether a gap in the statement gives you that right. Plumbing defects are not part of the form, so this remedy does not cover faults found in the pipes.

The statement is not a report on the condition of the home. The Queensland Government lists structural soundness, flooding history and previous building approvals among matters the seller does not have to disclose. Pipes, drains and hot water units fall outside the form, so a plumber's report is the buyer's main evidence about them. Read any notice listed under the QBCC or building laws closely, and ask the seller what work it relates to.

Council Searches, Drainage Plans and the Notifiable Work Register

Past plumbing work often leaves records that buyers can check. The QBCC sorts Queensland plumbing work into four categories: permit work, notifiable work, minor work and unregulated work, which owners may do without a licence. Notifiable work, which is reported to the QBCC after it is done, includes most work in existing buildings. The licensed plumber registers it with the QBCC on a Form 4, the form that records the work, within 10 business days of issuing the invoice. A copy must go to the customer or occupier within 20 business days of registration. Extending water supply pipes and installing a new water heater are both examples the QBCC gives.

The QBCC keeps a notifiable work register that can be searched by address to see whether plumbing work has been registered. Renovated bathrooms or recent hot water replacements with no registration may have been done without the required paperwork. Request invoices and Form 4 copies for that work from the seller, then pass them to your plumber. Permit work, such as plumbing for a new house or an extension, is generally assessed and inspected by the local council. Councils may therefore hold plans and inspection records from that process.

Brisbane City Council offers an inspection of records search, normally ordered while a property is being sold. Results can include plumbing and drainage information, stormwater network details, flooding reports and property notices. A standard search takes up to 12 business days, while the fast track option takes up to three business days. For new houses in Brisbane, plumbers supply an as-constructed drainage plan, a drawing of the drains as actually built, showing the sewer connection, underground drains and the water meter position. Other councils run their own record searches, so check with the council for the suburb you are buying in. The council search leaves out the water and wastewater account balance, which Urban Utilities provides on 13 26 57.

Your Pipes or the Utility's: Water and Sewer Responsibility

Water and sewerage in south east Queensland are run by different bodies depending on the council area. Urban Utilities serves Brisbane, Ipswich, Lockyer Valley, Scenic Rim and Somerset. Unitywater serves Moreton Bay, the Sunshine Coast and Noosa. The Gold Coast, Logan and Redland councils run their own water and sewerage services. Outside the south east, the local council website names the water provider for the property.

Unitywater states that property owners are responsible for all plumbing from the water meter onwards, including pipes, fixtures and fittings. It owns the pipes and equipment up to and including the meter, even where the meter sits inside the property. For sewer blockages, its guidance separates faults on its side of the property boundary from those inside your block. Faults on the owner's side become your cost once you settle, which is why drain footage matters to a buyer. Urban Utilities takes fault calls on 13 23 64, and Unitywater takes them on 1300 086 489. If a plumber traces a blockage to Unitywater's side, the plumber, not the customer, can claim Unitywater's blocked sewer identification fee, a payment for finding the fault.

One fitting the plumber should locate is the overflow relief gully, a grated outlet in the ground outside the house. When the sewer blocks, it lets wastewater spill outside so it does not back up through floor drains and toilets. Unitywater advises owners to check that this gully is not blocked or covered. Gullies buried under garden beds or covered by paving need to be raised or uncovered.

Filming Sewer and Stormwater Drains Before Settlement

A drain camera is a small waterproof camera on a flexible cable that the plumber feeds through the pipes from an inspection opening. Most homes have these openings near the house or out in the yard. The footage can show tree roots, cracked or shifted joints, sagging sections that hold water and pipes squashed by ground movement. Footage that records the distance to each fault lets another plumber price the repair from the same evidence. Filming with a report costs $250 to $550, and the process is explained in more depth in our drain camera inspection guide.

Once the camera finds damage, the repair options differ widely in cost. The right method depends on the condition of the pipe, its depth and what sits above it. Relining, which sets a resin-soaked sleeve hard inside the old pipe, costs $550 to $1,100 per metre plus a charge to reopen each side pipe. Digging up and replacing the line costs $250 to $550 per metre before lawn, paving or driveway are restored. Clearing a blocked drain with a machine costs $250 to $650, though cut roots can grow back if the pipe stays cracked. Compare these methods on our pipe relining and drain repairs page, or read about sewer repair and replacement.

Filming starts at an inspection opening, and the camera works along the line toward the sewer connection. Some camera heads have a built-in locator, a transmitter tracked from above, to mark the ground over a fault, showing where any digging would need to happen. Lines too blocked for the camera to pass may need clearing first, which adds time and cost. Keep the recording, because it gives you a record to compare against if a blockage appears after you move in. Some homes share a combined sanitary drain, which Brisbane City Council describes as a private drain connecting two or more properties to one sewer connection point. The owners served by that drain are responsible for maintaining it, each keeping the section on their own land in good order.

Stormwater is a separate system from the sewer and carries rain from roofs, downpipes and paved areas. Unitywater notes that councils own the stormwater pipes outside the property. Blocked or broken stormwater lines can leave water pooling against the slab or footings, the concrete base under the walls. Clearing a stormwater line costs $250 to $650, so a quick hose test of the downpipes during the visit is sensible.

Meter Tests, Hidden Leaks and Ageing Water Pipes

The water meter test is the simplest check for a hidden leak. With every tap, appliance and irrigation system turned off, the plumber notes the meter reading and checks it again after a short wait. Any movement with nothing running means water is escaping somewhere in the pipes. Hidden leaks raise water bills and can damage slabs, walls and footings over time. The plumber can then narrow the search with listening equipment or other water leak detection methods.

The plumber also notes the pipe material wherever it is exposed, such as under sinks, in the roof space and at the hot water unit. Older homes may still have galvanised, or zinc-coated, steel water pipes, which rust from the inside as they age. Newer homes use copper or cross-linked polyethylene, called PE-X, which is a flexible plastic pipe. If the plumber recommends replacing old pipework, read our water pipe replacement guide before you negotiate. REHAU makes pipe systems for hot and cold water services in homes. Iplex makes PVC pressure pipe, polyethylene pipe and PVC drainage and stormwater systems.

Water pressure can also be measured with a gauge fitted to an outside tap. Low pressure can come from corroded pipes, a partly closed valve or a supply fault, while very high pressure strains taps, valves and appliances. Fitted after the meter, a pressure limiting valve holds incoming pressure within a set range. The report should say whether one is fitted and whether it appears to work. Noisy pipes that bang when a tap shuts are also worth noting for a later repair.

Hot Water Units: Age, Valves and the 50°C Limit

The plumber reads the data plate on the hot water unit to find its model, capacity and date of manufacture. They check the tank for rust and leaks and look at the temperature and pressure relief valve, called the TPR valve, which releases water if heat or pressure gets too high. A sacrificial anode is a metal rod inside a storage tank that corrodes so the tank lining does not. Replacing a TPR valve costs $150 to $350, and a new anode costs $200 to $400. Replacing a heating element or thermostat, the part that controls temperature, in an electric storage unit costs $280 to $600.

Some signs at the hot water unit call for a closer look before you commit. Water pooling under the tank or rust streaks down the casing can mean the tank itself is failing. Constant dripping from the relief valve needs a plumber to find the cause. Gas units should be checked by a licensed gasfitter for scorching around the burner and flue, the pipe that carries fumes outside. Heat pump units have a fan and compressor that should run quietly, with the small pipe that drains condensation running away from the slab. Solar systems have collector panels on the roof that the plumber may only be able to view from the ground.

Business Queensland says stored hot water must be heated to at least 60°C to control bacteria such as Legionella. A temperature control device must be fitted to all new and replacement hot water systems, delivering water to taps at no more than 50°C to lower the risk of scalding. A tempering valve, which mixes cold water into hot to keep it at a safe temperature, is a common example, and replacing one costs $270 to $520. For a recently replaced unit, the plumber can check that a temperature control device was fitted. Solar and heat pump systems must be installed by a hot water installer holding a QBCC solar and heat pump endorsement.

Replacing an electric storage unit with the same type costs $1,350 to $2,400, so the age of the unit is relevant when you weigh up the price. iStore makes 180 litre and 270 litre heat pump hot water systems for Australian households. Emerald makes all-in-one and split system hot water heat pumps. A heat pump heats water by drawing warmth from the surrounding air into the tank. Compare repair and replacement on our hot water system repairs page, and read about thermostatic mixing valve servicing if the home has one.

Toilets, Taps, Showers and the Laundry

Each toilet is flushed several times while the plumber listens for water still running into the pan, the toilet bowl, after the cistern, the tank holding the flush water, refills. Cisterns that keep running waste water and need new washers or valves, and a cistern repair costs $160 to $400. Slow flushing or gurgling sounds can mean a partial blockage further down the line. Each pan should also be firmly fixed, with no water seeping around its base. If a toilet drains poorly, the usual fixes are set out in our blocked toilet repair guide. Seima makes wall-faced toilet suites, which sit flat against the wall, and Kohler makes toilets, basins and taps for Australian bathrooms.

Taps are run hot and cold to check the flow, drips from the spout and leaks around the body. Repairing a leaking tap costs $130 to $320, so a single drip is a small item in a negotiation. Under-sink pipes are checked for corrosion and seeping joints, and flexible hoses are checked for rust or swelling. hansgrohe makes shower systems, thermostatic mixers that hold a set water temperature, and kitchen mixers. Nero Tapware makes tapware, showers and toilets, and Dorf makes basin mixers, shower systems and kitchen tapware.

Shower recesses are checked for cracked grout, missing silicone and drummy tiles, which sound hollow when tapped. Swollen skirting boards, flaking paint or mould on the far side of the wall can mean water is escaping through the floor or walls. Waterproofing sits under the tiles and cannot be seen, so these signs are what the plumber has to go on. Stormtech makes linear drains, square floor wastes, which are the drain outlets set in the floor, and grates for showers and wet areas. Read about options from regrouting, which replaces the grout between tiles, to a full rebuild on our shower regrouting and leak repairs page.

The laundry sink, the washing machine taps and the floor waste are tested as well. The plumber checks that the sink drains freely and that the washing machine stop taps turn off fully. Clark makes kitchen sinks and laundry sinks with cabinets, and Abey makes laundry sinks, laundry tapware and washing machine stops. Kitchen sinks get the same flow and drainage test, with a look at any dishwasher and fridge water connections.

Backflow Devices, Irrigation and Rainwater Tanks

A backflow prevention device is a valve that stops polluted water flowing back into the drinking water supply. Redland City Council lists irrigation systems, fire hose reels and alternate water supplies among installations that may have a testable device, a backflow valve fitted with test points. Testable devices must be registered with the council and tested at least once a year by a plumber with a backflow endorsement on their licence. The tester sends a Form 9 test report to the council within 10 business days, and skipping the yearly test is an offence under the Plumbing and Drainage Regulation 2019. Each backflow device test costs $120 to $260, and the duty to arrange it passes to the new owner. Ask the seller for the latest test report if the property has a registered device.

Garden irrigation fitted after a tap appears on the QBCC list of unregulated plumbing that an owner can install without a licence. Conditions apply to isolating valves, which shut off water to one area, and backflow devices on the supply pipe, so a plumber should check any system with a more complex connection. Holman makes tap timers, drip irrigation fittings and solenoid valves, the electric valves that switch watering zones, for home gardens. Rainwater tanks connected to toilets or the laundry have pumps and valves that switch between tank and mains water, which the plumber can test. Read about pumps and mains backup on our rainwater tank plumbing page.

Gas Appliances and Who Can Work on Them

Gas hot water units, cooktops and heaters need a separate licence to work on. The QBCC states that it does not issue gasfitting licences, which come from the Chief Gas Examiner and Resources Safety and Health Queensland. When a gas installation is completed, the gasfitter issues a gas system compliance certificate confirming the work, and the owner receives the original. Request these certificates from the seller if gas appliances were installed recently.

Check that the plumber you book also holds a gasfitting licence if you want the gas appliances looked at during the same visit. Licensed gasfitters can check the connections, the appliance data plates and any signs of scorching around burners or flues. For follow-up work, find licensed gasfitters through our gas fitting page. Keep any compliance certificates you receive with the property records after settlement. Any gasfitting findings can be added to the plumbing report or attached as a separate note.

Asbestos in Older Queensland Homes

Queensland's official asbestos website says houses built before 1990 may contain asbestos. It notes that asbestos is found quite often in places such as under the kitchen sink, inside linen cupboards and in electrical boxes. Plumbers work in exactly these spaces, so tell the plumber the age of the home before the visit. Owners planning renovations are advised to have the property inspected by a trained professional first. Arrange asbestos testing if the report flags suspect material near pipes you plan to replace.

Homeowners can remove up to 10 square metres of non-friable asbestos without a certificate, though safety precautions still apply. Non-friable, or bonded, asbestos is material where the fibres are locked into cement or another binder. Larger jobs need a certificate or a contractor holding a current asbestos removal certificate. Ask any plumber quoting for pipe or bathroom work how they will handle material that may contain asbestos.

Unsewered Blocks and On-Site Sewerage Systems

Homes outside the sewer network treat their wastewater on site, and Logan City Council calls these on-site sewerage facilities. A septic system treats waste biologically and discharges it below ground. On-site treatment systems use mechanical, biological and filtration steps and discharge above ground or through buried irrigation. Logan requires aerobic wastewater treatment plants, which pump air through the waste to break it down, to be serviced every three months by a licensed service agent, and aerobic sand filter systems every year. Owners and tenants are responsible for keeping these systems maintained.

Request the service reports from the licensed agent, since Logan advises owners to keep copies of them. Gaps in servicing, alarms sounding or wet ground over the disposal area, where treated water is released, are reasons for a closer look. Pumping out a septic tank costs $450 to $1,000 per load plus travel. Other councils set their own servicing rules, so check with the council for the property. Plumbers who handle rural systems can be found through our Toowoomba and Darling Downs plumbers page and our septic tank repairs guide.

Buying a Rental Property, Unit or Townhouse

Investors buying a tenanted home should look at the fixtures with future water charges in mind. Anyone planning to pass water use charges on to tenants should read our rental water efficiency compliance guide before settlement. During the inspection, the plumber can record shower head flow rates, tap types and toilet flush details for each room. Form 2 must also list any residential tenancy agreements, or leases, that apply to the property. Those details help you plan upgrades for the first lease you sign as owner. Recording them now saves a second visit if you decide to change fittings later.

In a unit or townhouse, plumbing is split between your lot and the common property, which is the shared part of the complex. A body corporate is the group of all owners that manages that common property. Sellers of units in some complexes must provide a body corporate certificate with the disclosure statement. Read it with any recent meeting minutes for mentions of leaks, sewer repairs or hot water problems in the building. Plumbers who work on shared building pipes are listed on our strata and body corporate plumbing page.

Older Homes, New Builds and Renovated Homes

The age of the home changes which checks matter most. Homes built before 1990 may contain asbestos, so plumbers working under sinks and in wet areas need to know the build date. Older homes may have galvanised steel water pipes and sewer lines laid well before modern plastic pipe. Raised timber homes give easy access under the floor, so the plumber can see more of the pipework. Slab homes hide pipes in concrete, so meter tests and drain filming matter more there. Large trees close to an old sewer line are a good reason to book the camera.

Newer homes still need a check, especially where the original work has since been changed. Look on the notifiable work register for any bathroom renovation, new hot water unit or extended water pipes. Homes renovated without registered work may have plumbing that no one has recorded. Adding fixtures to a home on a combined sanitary drain is permit work that the council assesses and inspects. Permit records for that work can then be requested from the council.

Getting the Home Ready for the Plumber's Visit

Inspections run faster when the plumber can reach everything on arrival. The agent needs to arrange access to the house, the yard, the garage and any locked sheds or meter boxes. Water should be connected and the hot water unit switched on so taps, showers and the tempering valve can be tested properly. Cupboards under the kitchen sink, bathroom vanities and the laundry sink should be clear enough to see the pipes. Garden beds or mulch over inspection openings may need moving before the camera can go in. Mention pets, alarms or tenants at the property when you book, so the visit is not cut short.

Attending the visit lets you see faults in person and ask questions while the plumber is there. Bring the building report, the seller disclosure statement and any plans or invoices you have collected. Note which areas the plumber could not reach, in case a second visit is needed. Ending with a short walk-through, where the plumber names the biggest items, makes the written report easier to follow.

What a Useful Plumbing Report Contains

The written report should list each test carried out, the result and photos of every fault. Drain footage should come as a recording, with the distance from the inspection opening to each problem and the pipe material noted. The hot water section should give the make, model, age and the condition of each valve. Areas that could not be reached need to be named along with the reason. The plumber's QBCC licence number and the date of the visit should appear on the first page. Rough repair costs next to each fault help you decide what to raise with the seller.

Trade terms should be explained in the report or in a short glossary at the end. One-line verdicts with no list of tests are hard to use in a negotiation. Keep the report after settlement, as the meter result, hot water details and drain footage help with future maintenance. Agree on a delivery date that falls before your condition date.

If you buy the home, the report becomes a starting list for maintenance. Items marked for monitoring, such as a slow drain or an ageing hot water unit, can be checked again in a year. Store the drain footage with the property documents so a future plumber can compare it with new footage. Share the report with any plumber you hire for repairs, which saves paying for the same tests twice. File the paperwork for those repairs alongside it, including Form 4 copies for any notifiable work.

Checking a Plumber's QBCC Licence

The QBCC says most plumbing work in Queensland is regulated and needs a QBCC licensed plumber or drainer. Minor work, such as clearing a blocked drain or repairing a broken pipe, still needs a licensed plumber even though no approval or reporting is required. Unregulated tasks an owner can do include replacing a shower head, changing a tap washer and replacing a cistern washer. Check the plumber's licence on the QBCC licensee register, a free online search, before you book. Ask for the licence number on the quote and confirm it matches the name on the report and invoice.

Plumbers based near the property know the local water provider and council rules. Find licensed plumbers in the city through hiring a plumber in Brisbane, or north of the city through Sunshine Coast plumbers. Other plumbing jobs across the state are grouped in our Queensland plumbing services hub. Regional and rural visits can add a travel fee of $60 to $250.

Acting on the Findings Before Your Deadline

Findings only help while your inspection condition or cooling-off period is still running. Get a written repair quote for each serious fault, listing the work, the materials and the price. Your solicitor or conveyancer can explain what the contract allows, such as asking the seller to fix the fault, agreeing on a lower price or ending the contract. The Queensland Government notes that buyers need terms in the contract that let them cancel after poor inspection reports. Keep every quote with the report in case the findings are questioned later.

Small faults, such as a dripping tap or a running cistern, cost little to fix and may not justify a price discussion. Larger items, like a cracked sewer line, a failing hot water unit or a hidden slab leak, are the findings that can. If you go ahead, plan repairs for the first weeks after settlement and group small jobs into one visit to save on call-out charges. Queensland Government advice is to inspect the property 2 to 3 days before settlement to confirm it is in the same condition. Run the taps and flush the toilets on that visit to check nothing has changed. Compare repair prices in our Queensland plumber pricing guide.

How to Brief Plumbers for Comparable Quotes

Give every plumber the same details so the quotes can be compared fairly. Include the address, the age of the home, the number of bathrooms and toilets, the hot water type and whether the home is on sewer or a septic system. State the date your cooling-off period or inspection condition ends. Say which tests you want, such as drain filming, a meter leak test or a hot water check, and the report format you need. Photos of the hot water data plate and the meter box help each plumber plan the visit.

Differences in price between quotes come mainly from what each one includes. One plumber may quote a fixture check with a short summary, while another includes drain footage and a full written report. Confirm whether the call-out, travel and report writing are included in the quoted figure. Check too whether the price covers filming both the sewer and the stormwater lines. If the agent can only offer access on a weekend, an after-hours call-out costs $180 to $450 before any work begins. Paying slightly more for a report delivered on time is better value than a cheaper report that arrives after your deadline.

What to Look Out For in Pre-Purchase Plumbing Quotes

Be wary of a quote that bundles the inspection with a fixed repair price before the plumber has seen the property. Plumbers hoping to win the repair work have an incentive to report faults, so ask for photos and footage behind every finding. Quotes missing a QBCC licence number, a business name or a written list of checks give you little to rely on if something goes wrong. Check that drain filming includes a recording, not just comments at the end of the visit. Make sure the quote states what happens if a blockage stops the camera, since clearing it costs $250 to $650 extra.

Leak testing can mean a quick meter check or a full audit with several methods, and the two cost very different amounts. Full property leak audits cost $400 to $1,000, so the quote should name one if it is included. Confirm the report will arrive as a file you can share with your solicitor and the selling agent. Above all, get the visit date and report date in writing so both fall inside your contract deadline.

Plumbers for Pre-Purchase Checks Across Queensland

We connect Queensland home buyers, investors and unit buyers with QBCC licensed plumbers for pre-settlement plumbing checks, drain filming and meter leak tests. Pick your region below, describe the property once and compare quotes from plumbers who work in that area.

▶ Brisbane 31 areas
Brisbane CBD Fortitude Valley New Farm Newstead Teneriffe Paddington Toowong Indooroopilly St Lucia Chapel Hill Kenmore Mount Ommaney Sunnybank Coorparoo Camp Hill Carindale Bulimba Hawthorne Wynnum Manly Chermside Aspley Everton Park The Gap Ashgrove Stafford Nundah Clayfield Hamilton Carseldine Bridgeman Downs
▶ Gold Coast 26 areas
Southport Surfers Paradise Broadbeach Mermaid Beach Miami Burleigh Heads Palm Beach Currumbin Coolangatta Tugun Robina Varsity Lakes Mudgeeraba Nerang Carrara Ashmore Benowa Helensvale Hope Island Coomera Upper Coomera Oxenford Pacific Pines Mount Tamborine Currumbin Valley Ormeau
▶ Sunshine Coast 26 areas
Maroochydore Mooloolaba Alexandra Headland Buderim Sippy Downs Caloundra Golden Beach Currimundi Kawana Waters Coolum Beach Peregian Beach Noosaville Noosa Heads Tewantin Cooroy Pomona Eumundi Nambour Yandina Palmwoods Woombye Maleny Montville Mapleton Beerwah Landsborough
▶ Moreton Bay & Redcliffe 29 areas
Redcliffe Scarborough Margate Woody Point Clontarf Kippa-Ring Rothwell Deception Bay North Lakes Mango Hill Griffin Murrumba Downs Kallangur Petrie Lawnton Strathpine Bray Park Albany Creek Warner Cashmere Samford Dayboro Caboolture Morayfield Burpengary Narangba Bribie Island Woodford Wamuran
▶ Ipswich & Lockyer Valley 28 areas
Ipswich Booval Bundamba Goodna Redbank Springfield Springfield Lakes Brookwater Augustine Heights Ripley Yamanto Raceview Flinders View Karalee Karana Downs Rosewood Marburg Walloon Plainland Hatton Vale Laidley Gatton Forest Hill Withcott Helidon Grandchester Esk Lowood
▶ Logan & Redlands 28 areas
Logan Central Woodridge Kingston Slacks Creek Springwood Daisy Hill Shailer Park Loganholme Loganlea Meadowbrook Beenleigh Eagleby Browns Plains Regents Park Marsden Jimboomba Yarrabilba Cleveland Capalaba Victoria Point Wellington Point Thornlands Alexandra Hills Birkdale Ormiston Redland Bay Mount Cotton Russell Island

QLD Pre-Purchase Plumbing FAQs

Is there enough time in the Queensland cooling-off period for a plumbing inspection?
The standard Queensland contract gives buyers five business days of cooling-off, when they can still pull out, starting on the day they receive a copy signed by both parties. Ending the contract in that time lets the seller deduct up to 0.25% of the purchase price. Auction purchases have no cooling-off period, and buyers can also waive or shorten it in writing. Five business days is tight for a plumber's visit, a report and repair quotes. A written inspection condition in the contract gives you more certainty, so talk to your solicitor before signing.
How much does a pre-purchase plumbing inspection cost in QLD?
Quote Yard's Queensland price guides give no single figure for a whole-house inspection, so plumbers price it on quote. Labour starts with a call-out and first hour at $120 to $250, then $95 to $150 for each extra hour. Drain filming with a report adds $250 to $550 when it is charged separately. A visual check with a water meter test costs $150 to $300 if you want leak testing. All of these figures are 2027 estimates for Queensland.
Does a building and pest inspection include the plumbing?
A building inspector looks for obvious defects, and the QBCC lists leaking ceilings, missing waterproofing and drainage problems among them. The inspector does not film the sewer, test the water meter or check hot water valves. For specific concerns, the QBCC suggests a more detailed report from an appropriate expert, such as a plumber. Booking both inspections gives you a view of the structure and the pipes together.
Will the seller disclosure statement mention plumbing problems?
The seller disclosure statement, called Form 2, has been required since 1 August 2025 under the Property Law Act 2023. It covers title, encumbrances such as rights others hold over the land, zoning, government notices, pools and notices under building, planning and QBCC laws. Structural soundness and flooding history are among the matters a seller does not have to disclose, according to the Queensland Government. The statement does not describe the condition of pipes, drains or the hot water unit. A plumber's inspection is the way to learn about those.
Who is responsible for the water and sewer pipes on a Queensland property?
Unitywater says owners are responsible for all plumbing from the water meter onwards, while the utility owns everything up to and including the meter. For sewer blockages, Unitywater handles faults on its side of the property boundary and owners pay for those inside the property. Urban Utilities serves Brisbane, Ipswich, Lockyer Valley, Scenic Rim and Somerset, while the Gold Coast, Logan and Redland councils run their own services. Check with the provider for your area, because each one publishes its own guidance.
How can I check whether past plumbing work was registered?
Notifiable plumbing work, which covers most work in existing buildings, must be registered with the QBCC on a Form 4. Registration is due within 10 business days of invoicing, and the owner or occupier must receive a copy within 20 business days. You can search the QBCC notifiable work register by address to see whether work has been registered. Ask the seller for invoices and Form 4 copies for any recent bathroom or hot water work.
What hot water rules should a buyer know about?
Business Queensland says stored hot water must be heated to at least 60°C to control bacteria. All new and replacement hot water systems must have a temperature control device that delivers no more than 50°C to taps. Solar and heat pump systems must be installed by an installer with a QBCC solar and heat pump endorsement. During the inspection, the plumber can read the data plate to estimate the unit's age and check its valves for leaks.
Does a home with a septic system or treatment plant need extra checks?
Yes, because these systems treat wastewater on the property and need regular servicing. Logan City Council requires aerobic treatment plants to be serviced every three months by a licensed service agent. Owners and tenants are responsible for maintaining the system, and Logan advises keeping copies of the service reports. Ask the seller for those reports and have the plumber check the tank, the alarm and the area where treated water drains away. Pumping out a septic tank costs $450 to $1,000 per load plus travel, as a 2027 estimate.
Can I fix small plumbing faults myself after settlement?
Owners can do a few unregulated jobs without a licence, according to the QBCC. These include replacing a shower head, replacing the jumper valve or washer that stops a tap dripping, and replacing washers in a toilet cistern. Cleaning a ground-level grate on a drain and replacing caps on ground-level inspection openings are also on the list. Most other plumbing work in Queensland is regulated and needs a QBCC licensed plumber or drainer.
What should I do if the plumbing report finds a serious fault?
Get a written repair quote for each serious fault while your condition or cooling-off period is still running. Share the report and quotes with your solicitor or conveyancer, who can explain the options your contract allows. Those options may include asking the seller to repair the fault, agreeing on a lower price or ending the contract. Keep the report and quotes with your contract papers in case the findings are disputed.

More Checks Before You Sign

For Trades & Contractors - QLD

Queensland plumbers who carry out buyer inspections and the repairs that follow can find work on the QLD job leads board, along with listings under plumber jobs in QLD and drain plumber jobs.

Buying a Home in Queensland?

Post your job and compare quotes from QBCC licensed plumbers for pre-purchase plumbing checks, drain filming and meter leak tests.

Get Free Plumber Quotes

About This Guide

This guide is general information only, and Queensland property laws, QBCC requirements, water provider processes, product details and prices can change. Confirm requirements with your solicitor or conveyancer, the QBCC, your water provider and a licensed plumber before you rely on any inspection or start work.

Reviewed by The Quote Yard Editorial Team

Published 19 November 2026 ·

How The Quote Yard Works

We connect you with independent local tradies and service providers, we don't perform any trade work ourselves. Tradies provide their own quotes directly to you. Always confirm licensing, insurance, and scope of work before engaging any provider.

All Queensland tradies are required to hold appropriate QBCC licences. Verify at the Queensland Building and Construction Commission.
Prices are 2027 estimates for pre-purchase plumbing checks in Queensland. Whole-house inspections are priced on quote, and the figures exclude repairs, asbestos work, gas work and regional travel unless a row says otherwise.
Need work done? Get free quotes. Post a Job – It's Free