Leaking, Rusty or Ageing Water Pipes?

Tell us the suburb, roughly when the house was built, whether it is highset (raised on stumps), lowset or on a concrete slab, which water provider bills you and where the leaks have been. We will connect you with licensed Queensland plumbers who can each price the same repair or repipe, meaning a full replacement of the pipes.

Get Free Pipe Replacement Quotes

Typical Costs (2027 Estimates)

Accessible copper section repaired$250 - $600
Copper repair in a roof space$350 - $800
Meter to house pipe replaced$800 - $3,000
Slab leak repaired by direct access$1,500 - $5,000
Repipe, three-bedroom home with underfloor access$3,000 - $6,000
Full house repipe$3,000 - $15,000+
Plumber hourly rate, normal hours$95 - $150
Call-out and first hour$120 - $250

All figures are 2027 estimates for licensed plumbing work in Queensland. Leak searches, plaster patching, tiling, painting and restoring paving or lawn are extra unless the quote lists them.

Water Pipe Replacement Services QLD - Get Local Quotes

Water pipe replacement in Queensland ranges from cutting out one leaking length of copper to renewing every supply line between the water meter and the taps. Supply pipes stay full of water at mains pressure, so a failure keeps running until the stop tap at the meter is turned off. Older Queensland houses may still have galvanised steel lines that rust inside, while ageing copper can leave blue-green stains in basins or give tap water a metallic taste. Replacing supply pipes in an existing home is notifiable work under Queensland rules. That means a licensed plumber does the job and then registers a Form 4, a notice of the completed work, with the QBCC, the state building regulator. Your water provider looks after the network up to the meter or connection point, and the owner pays for every pipe on the property side. A hidden leak under a slab or in a buried line may qualify for partial relief on the water bill once a licensed plumber has fixed it. Highset homes on stumps can be repiped from underneath, while slab homes need new lines run through the roof and walls. Concealed leak relief rules differ between Urban Utilities, Unitywater and the council water providers, so the wording on the plumber's invoice matters. Water pressure above 500 kilopascals (kPa) indoors also strains new pipes unless a valve that limits pressure is fitted. Prices on this page are 2027 estimates for section repairs, meter line replacement and full house repipes. Post your job on The Quote Yard to receive quotes from licensed Queensland plumbers.

New Supply Pipes for Queensland Homes

A repipe can mean one repaired length, a single bathroom wing or every line in the house, and it may start with a buried pipe from the meter or a leak under the slab. We can connect you with licensed plumbers from Brisbane to the far north who will each quote from the same written scope.

Get Free Quotes

At a Glance - Queensland Water Pipe Replacement Prices (2027 Estimates)

Job 2027 Estimate How It Is Priced What Moves the Price Paperwork
Accessible copper section repaired $250 - $600 Fixed Pipe size and reach Minor work, no Form 4
Copper repair in a roof space $350 - $800 Fixed or hourly Roof height and insulation Minor work, no Form 4
Meter to house pipe replaced $800 - $3,000 Fixed after locating Length, depth and paving Form 4
Slab leak repaired by direct access $1,500 - $5,000 After detection Floor coverings and cutting Depends on scope
Galvanised pipes replaced, full house $3,000 - $10,000 Fixed after site visit House size and access Form 4
Repipe, two-storey brick home $8,000 - $15,000+ Fixed after site visit Cavities and floor access Form 4
Bathroom or laundry zone repiped Priced on quote Fixed after site visit Fixture count and linings Form 4
Pressure limiting valve installed $150 - $400 Fixed Valve size and position Ask the plumber

What Changes a Queensland Repipe Price

Main cost drivers
House type sets the route for new lines. Highset homes on stumps give room underneath, while slab homes send pipes through the roof and down inside walls.
A leak that cannot be seen has to be found first. Searches are charged as their own item before any pipe is priced.
The buried line from the meter to the house is a separate item. Its price rises with length, depth and the paving or driveway above it.
Repairing walls, tiles, paint and paving afterwards, called making good, may be done by other trades and priced apart from the plumbing.
A quote that names no pipe system, leaves out patching or says nothing about the Form 4 completion notice cannot be compared fairly with one that does.

Replacing Water Supply Pipes in Queensland Homes

Water pipe replacement means taking out the pipes that carry drinking water through a property and installing new ones in their place. Queensland plumbing law calls these supply pipes, meaning the pipes that supply water within the premises. The job can be one damaged length behind a laundry sink or every hot and cold line from the meter to the last tap. Unlike drains, supply pipes hold mains pressure all day and night, so a failure keeps leaking until the water is shut off at the stop tap, the valve at the meter. For the wider range of jobs a licensed plumber handles, see our guide to plumbing services in Queensland.

The reasons for repiping vary from one Queensland house to the next. Unitywater says a metallic taste in tap water usually comes from corrosion of household copper plumbing, which can also stain basins blue-green. Older homes can have galvanised steel lines, a zinc-coated steel pipe that rusts from the inside as it ages. City of Gold Coast says pressure in its network can reach around 900 kPa, well above the 500 kPa (kilopascals, the unit for water pressure) allowed inside a building.

Replacing supply pipes is regulated plumbing work, and the Queensland Building and Construction Commission (QBCC) says it must be done by a licensed plumber. In an existing home, the Plumbing and Drainage Regulation 2019 lists replacing supply pipes as notifiable work. That category needs no council permit or inspection, but the plumber must register a Form 4, a notice of the completed work, with the QBCC. Fixing a broken or damaged pipe counts as minor work instead, which still needs a licensed plumber. Prices on this page are 2027 estimates drawn from Quote Yard Queensland pricing pages.

What Repiping Costs in Queensland (2027 Estimates)

Pipe work in Queensland is priced in a few ways, depending on how much the plumber can see before starting. Repairing an accessible section of copper pipe has a 2027 estimate of $250 to $600, while the same repair in a roof space costs $350 to $800. Replacing the full buried pipe from the meter to the house runs from $800 to $3,000, depending on length and what sits on top of it. Full house repipes range from $3,000 to more than $15,000. These ranges come from our Queensland page on burst pipe repairs and appear here as 2027 estimates.

Full repipe prices vary widely with the type of house. Three-bedroom homes with open access under the floor sit at $3,000 to $6,000, because new lines can run between the stumps that hold the house up. Two-storey brick homes cost $8,000 to more than $15,000, since pipes must pass through wall cavities and between floors. Replacing every galvanised steel line in a house has its own range of $3,000 to $10,000. A slab home with a leak under the concrete needs a different approach, with a direct repair priced from $1,500 to $5,000. Repiping a single bathroom or laundry has no separate range in our figures, so that work is priced on quote.

When two full repipe quotes are thousands of dollars apart, compare the scope before the hourly rate. One plumber may include outdoor taps, the hot water lines and the meter connection, while another stops at the wet areas. Patching, painting and tiling may be priced, excluded or left vague. Each plumber should list every fixture they will reconnect, so the counts can be matched line by line.

Pipe Job 2027 Estimate Pricing Basis What to Expect
Accessible copper section repaired $250 - $600 Fixed Pipe reachable without cutting linings
Copper repair in a roof space $350 - $800 Fixed or hourly Roof height and insulation slow the work
Meter to house pipe replaced $800 - $3,000 Fixed after locating Paving, driveways and depth
Slab leak repaired by direct access $1,500 - $5,000 Quoted after detection Floor coverings lifted and relaid
Concrete cut and reinstated for a slab repair $300 - $800 Fixed Tiles or timber on top are extra
Repipe, three-bedroom home with underfloor access $3,000 - $6,000 Fixed after site visit Lines run between the stumps
Repipe, two-storey brick home $8,000 - $15,000+ Fixed after site visit Cavity and floor access
Galvanised pipes replaced, full house $3,000 - $10,000 Fixed after site visit Rusted fittings at each outlet
Full house repipe, general range $3,000 - $15,000+ Fixed after site visit Size, storeys and access

Call-Out Fees, Hourly Rates and Leak Searches

Hourly charges apply when the job starts with a search or when access is uncertain. Queensland plumbers bill $95 to $150 per hour during normal working hours, while the call-out and first hour together come to $120 to $250. After hours or weekend call-outs run $180 to $450 before any work starts, with Sundays and public holidays at the top of that range. Regional jobs some distance from the plumber's base can carry a travel charge between $60 and $250. These shared rates match our Queensland plumber pricing guide.

Hidden leaks have to be found before anyone can price the pipe. General leak detection visits in Queensland cost $300 to $800, and a search under a slab falls in the same range. Visual checks with a meter test cost $150 to $300, while acoustic detection, which listens for escaping water, costs $250 to $500. Tracer gas detection pushes a safe gas into the line and finds where it escapes, and it costs $400 to $800. Request the search and the repair as separate invoice lines, so each part can be checked against the ranges.

Thermal imaging uses a camera that shows warm and cool patches, which can help locate a hot water leak behind plaster. It costs $300 to $600 as a separate inspection. FLIR makes the FLIR ONE thermal camera along with handheld thermal cameras used for building inspection. Camera images alone do not prove a leak, so plumbers combine them with meter readings and pressure tests. Cold water leaks can show up less clearly on a thermal image than hot water leaks. Each method is described in more depth on our water leak detection page.

Signs the Supply Pipes Are Failing

The first sign of a failing supply pipe sometimes shows up on the water bill before any water appears on the floor. Bills that climb without any change in household use can mean water is escaping underground or inside a wall. With every tap off, a meter dial that keeps turning shows water is still moving somewhere on the property. Damp patches on plaster, swelling skirting boards and lifting floor tiles near wet areas are other clues to look for. Taps that spit air or run brown after a shutdown can also mean a corroded pipe.

Unitywater lists several water quality clues linked to the pipes on a property. It says copper corrosion can stain basins, sinks, showers and toilet bowls blue-green, and can also give water a metallic taste. The same staining may appear in new houses with new copper pipes and reduce over time. In the short term, Unitywater advises flushing the affected tap for two minutes. For the longer term, it advises asking a licensed plumber to inspect the pipes for corrosion and replace them if required.

Brown or discoloured water can come from the street mains or from corroded pipes on the property itself. For discoloured water, Unitywater advises running the outdoor tap nearest the meter, for up to five to ten minutes, until it clears. If only your home is affected and the colour keeps returning, ask a plumber to check the house pipes. Checking the pipe material at the meter and at a few outlets is a quick first step.

A simple meter check can be done before calling anyone. Turn off every tap, make sure no appliance is filling and note the meter reading or the position of its smallest dial. Wait an hour without using any water, then read the meter again. Any change means water is passing through the meter somewhere on the property. The plumber can then work out whether the loss is in the house, the buried line or a fitting such as a toilet cistern. Write down both readings and the times, because they help the plumber and any later leak relief claim.

Galvanised Steel and Ageing Copper in Queensland Houses

Galvanised steel pipe is steel coated in zinc, and it was used for water supply in older homes. Over time the inside of the pipe rusts and narrows, which lowers flow and can colour the water. QBCC guidance gives replacing galvanised water supply pipework with another type, such as polyethylene, a flexible plastic pipe, as an example of notifiable work. Unitywater says that when it replaces a meter and finds corroded galvanised pipe, it may install a temporary above-ground service. The owner must then arrange a permanent service, which a licensed plumber has to lay.

Copper supply lines can give long service when they are sound and well supported. They can still fail at joints, through small pinhole leaks or where they have been crushed, rubbed or nailed. One pinhole in an otherwise sound line is a repair job. Pinholes appearing in different rooms suggest a wider problem with the pipe itself. Plumbers who cut out a failed section can show you the inside of the pipe, which helps when choosing between more repairs and a repipe.

Houses extended or renovated in stages can end up with several pipe materials. Newer kitchens may sit on plastic pipe while the original bathroom still runs on copper or galvanised steel. Joints between different metals and old fittings need checking whenever new work connects to old. Having the plumber note which material runs where makes repipe quotes easier to compare.

One Length, One Zone or the Whole House

Not every leak justifies new pipes throughout the house. One failure caused by a nail, a loose pipe clip or a damaged fitting is a repair, priced as a section job. Two or three leaks in the same material within a short time are a stronger reason to replace that run. Galvanised steel that has narrowed inside, or copper that shows corrosion at several outlets, is a reason to price a repipe. If the walls are already open for a renovation, replacing the pipes at the same time avoids opening them again later.

Repiping can also be done by zone, which means renewing the lines to one area such as a bathroom, kitchen or laundry. Zone repipes suit a house where one wing is older or has had repeated leaks. They also suit a staged budget, as long as each new section connects properly to the next. Zone work has no separate range in our Queensland figures, so expect it to be priced on quote after a site visit. The plumber should show where new pipe joins old and fit an isolation valve, a tap that shuts off one area, where it helps. For bathroom work, our page on bathroom renovation plumbing explains how pipe work fits around the other trades.

A full repipe renews every supply line from the meter connection to each fixture. It costs more at the start but removes the old material from the whole house in one job. Plumbers can price it more firmly once they have looked under the floor, in the roof and at the meter. If you are weighing a repipe against ongoing repairs, ask for both prices in writing.

Who Owns the Pipe From the Meter to the House

Responsibility for water pipes in Queensland depends on which water service provider supplies the address. Urban Utilities serves the Brisbane, Ipswich, Lockyer Valley, Scenic Rim and Somerset council areas. Its customer charter says it maintains the drinking water service up to the property connection point, where the network meets the private pipes. It asks customers to engage a licensed plumber for any leaks on their side of the water meter. Urban Utilities takes faults and emergencies on 13 23 64 at any hour of the day.

Unitywater serves the Moreton Bay, Sunshine Coast and Noosa council regions. It says plumbing problems on private property are the owner's responsibility to investigate and repair. Its customers can stop water to the whole property by turning the stop tap on the meter clockwise. In the Redlands, City Water, which is owned by Redland City Council, says owners handle leaks on the property side of the meter, including all property plumbing. City of Gold Coast and City of Logan also run their own water services, so check your water bill to see which provider serves your address.

The pipe from the meter to the house can run underground beneath driveways, paths and gardens. Replacing its full length has a 2027 estimate of $800 to $3,000, rising with length and the surfaces that must be lifted and relaid. Plumbers can lay new polyethylene pipe in a fresh trench beside the old one, which avoids digging the old pipe out. Paving, concrete paths and garden beds along the route are restored at extra cost unless the quote says otherwise. The sewer is a separate system with its own ownership rules, explained on our sewer repair and replacement page. Its condition is checked with a drain camera inspection, not with water pipe testing.

Water Providers and Their Contacts

Check your water bill first
Urban Utilities: Brisbane, Ipswich, Lockyer Valley, Scenic Rim and Somerset. Faults and emergencies 13 23 64, 24 hours.
Unitywater, which serves Moreton Bay, Sunshine Coast and Noosa, takes calls on 1300 086 489.
City Water, owned by Redland City Council: owners look after leaks on the property side of the meter.
City of Gold Coast: water pressure questions on 1300 000 928.
City of Logan: runs its own water network and concealed leak remissions.
Outside South East Queensland, the local council may supply the water. Read the water notice for the right contact before reporting a leak near the meter.

Concealed Leak Relief After a Hidden Pipe Failure

A concealed leak is water escaping from hidden pipework on the owner's side of the meter, such as underground or under a slab. Water providers in South East Queensland offer relief on part of the extra charges once such a leak is found and fixed. The Queensland Government lists City of Gold Coast, City of Logan, Redland City Council and Urban Utilities among providers in a bulk water remission scheme, which refunds part of a state charge. Under that scheme, eligible pensioners get back 100 per cent, and other eligible customers 70 per cent, of the state bulk water charge on the extra water lost. Each provider sets its own application rules, so read them before booking the plumber.

Urban Utilities requires the leak to be repaired by a licensed plumber within one month of finding it or being told about it. The application must be made within six months, with the plumber's report or invoice attached. Leaks inside the house, at taps and toilets, in hot water systems, irrigation, pools and external fittings are excluded. Leaks linked to building, landscaping or concreting work in the previous six months are also excluded. Relief covers up to two billing periods, and the same property cannot receive relief on its water usage charges again within three years. Make sure the invoice says where the leak was and what was repaired.

Unitywater refunds residential customers 70 per cent of the excess water usage charges from a concealed leak, and pensioners 100 per cent. Its allowance covers up to two billing quarters and can be claimed once per property, per ownership. The leak must have been repaired within the past 12 months, with a plumber's invoice or a statutory declaration, a signed and witnessed written statement, as evidence. In Logan, the leak must be fixed within one month and the application made within three months of the bill showing higher use. Logan also asks for a licensed plumber's report on the repair and a recent meter reading.

Mains Pressure and the 500 kPa Limit Indoors

Water pressure is measured in kilopascals, written kPa, and a higher number means more force behind the water. City of Gold Coast says pressure in its network can vary from 220 kPa to around 900 kPa. It cites the Australian Standard AS/NZS 3500, which limits operating pressure inside a building to 500 kPa, other than at a fire service outlet. The city adds that buildings constructed or renovated since 2003 may already have a pressure reduction valve, which lowers incoming pressure, near the meter. Pressure above the limit puts extra load on pipes, joints, tap washers and appliance hoses.

Urban Utilities sets a minimum service standard of 21 metres head of water in most areas. In designated trickle feed areas, where a slow supply fills a storage tank, and lower pressure areas, the minimum is 10 metres. Metres head is another way of stating pressure, based on the height of a column of water. These are minimum standards and do not cap the pressure a house may receive. Plumbers can fit a gauge to an outside tap and read the static pressure, meaning the pressure with no water flowing. That reading belongs on any repipe quote, along with the plan for keeping pressure within the limit.

Installing a pressure limiting valve on the owner's side of the meter has a 2027 estimate of $150 to $400. Unitywater says these devices reduce and stabilise pressure from the mains supply. City of Gold Coast says a licensed plumber is needed to repair or adjust a pressure reduction valve. On a repipe, ask whether the valve will be fitted before the new lines are tested.

Choosing the Replacement Pipe and Fittings

Copper, PE-X and polyethylene are three pipe types plumbers use for supply lines. PE-X stands for cross-linked polyethylene, a plastic pipe soft enough to curve through framing, so a run needs fewer joints. Polyethylene, known as poly pipe, is used for buried lines such as the run from the meter to the house. Copper comes in rigid lengths, and plumbers join it with solder or with press fittings that seal once a powered tool crimps them onto the pipe. Each system needs its own matching fittings, so the quote should name the system and its maker.

Iplex makes Poliplex PE100 pipe, one of its polyethylene pressure pipe products. Philmac makes PUSH fittings, which connect polyethylene pipe by pushing it in, and a Metric Pipe Repair Kit for metric poly pipe. Galvin Engineering makes mini dual check valves and property ball valves in its civil range. A dual check valve stops water flowing back toward the supply, while a ball valve shuts the water off with a quarter turn. These parts can be replaced while the trench near the meter is open, which saves a second dig.

The chosen pipe should suit hot or cold use, the route and the water supply at the address. Check what warranty the pipe maker offers and whether it depends on the installer being trained in that system. Plumbers who install one system regularly may work faster with it, which can lower the labour cost. Using parts from several unrelated systems on one job can make later repairs harder. New homes follow a different process again, described in our guide to new home plumbing.

Backflow means water flowing the wrong way, from a property back toward the drinking water supply. Where a home already has a testable backflow prevention device, a one-way valve that blocks reverse flow, the new pipework should keep it in place and easy to reach. Testing one of these devices has a 2027 estimate of $120 to $260 per device. Owners can read more on our page about backflow prevention device installation and testing.

Running New Lines Through Highset, Lowset and Slab Homes

The shape of a Queensland house has a large effect on the labour in a repipe. Highset homes and older timber houses raised on stumps leave room underneath, so new lines can be clipped under the floor and brought up into each room. Lowset brick homes on a concrete slab have no space below, so plumbers run new lines through the roof and drop them inside walls. Two-storey homes add the task of getting pipes between floors without opening finished ceilings. Each route changes how much wall and ceiling lining must be cut and repaired.

Roof work needs safe access, lighting and room to move between the trusses, the timber frames that hold up the roof. Insulation and old wiring in the roof can slow the job, and an electrician may need to check any damaged cables. Underfloor work has its own problems, such as low clearance, damp soil and pests. Plumbers who price without looking may add a large allowance for access they cannot see. Before comparing prices, find out how each plumber plans to reach every outlet.

Slab homes with a leak under the floor need a decision about whether to dig or bypass. A direct repair cuts the slab over the leak, with concrete cutting and reinstatement estimated at $300 to $800 on top of the pipe work. Bypassing abandons the failed line under the slab and runs a new one through the roof or walls instead. Floor coverings such as tiles and timber can make a direct repair cost far more than the pipe itself.

Notifiable Work, Minor Work and the Form 4

Queensland sorts plumbing into categories that decide what paperwork follows a job. Notifiable work can be done without a council permit or mandatory inspection, and the QBCC says it includes most work in existing homes. Replacing, altering, extending or removing supply pipes in an existing house is notifiable work under the regulation. Minor work, such as repairing a broken or damaged pipe, still needs a licensed plumber but is a separate category. Permit work, such as plumbing for a new building, needs a permit from the local council before it starts.

For notifiable work, the plumber registers a Form 4 with the QBCC within 10 business days of issuing the invoice. The fee is $36.88 when lodged online through the QBCC Portal, or $49.80 for a paper form. The licensee must then give the customer a copy within 20 business days. Owners can use the QBCC online registers to check whether a Form 4 has been registered for their property. If no copy arrives, the QBCC accepts complaints about notifiable work that was not registered. Keep the Form 4 with the house records for insurance claims and any future sale.

Some parts of a repipe fall into their own notifiable categories. Installing, replacing or removing a water heater is notifiable work, and so is work on a temperature control device, a valve that limits how hot the water is at the taps. One QBCC example lists altered water supply pipework, a temperature control device and a new water heater as separate categories on one job. Ask the plumber which categories apply to your job before work starts.

Some small jobs need no licence at all, because the QBCC classes them as unregulated work. The list includes replacing a showerhead, a home water filter cartridge, or the jumper valve or washer in a tap, the small parts that stop a drip. Replacing washers in a toilet cistern and caps on ground-level inspection openings, the capped access points, of a sanitary drain, the drain that carries toilet and sink waste, are also on it. Digging or refilling a trench as a simple task alongside the plumbing is unregulated too, though the pipe laid in it is not. Any work on the supply pipes themselves still needs a licensed plumber.

Category Who Can Do It Pipe Job Examples Paperwork
Unregulated work Anyone Replacing a showerhead or a tap washer None
Minor work Licensed plumber Repairing a broken or damaged pipe No Form 4
Notifiable work Licensed plumber Replacing supply pipes, water heaters, temperature control devices Form 4 within 10 business days
Permit work Licensed plumber with council permit Plumbing for a new building Council permit and inspections

Hot Water Lines, Tempering Valves and the Heater

Hot water pipes are part of a full repipe, and they connect to the water heater through valves that control temperature. Business Queensland says hot water storage systems must heat water to at least 60°C to stop bacteria such as Legionella growing. It also says hot water should reach taps at no more than 50°C. A temperature control device, such as a tempering valve that blends hot and cold water, must be fitted to all new and replacement hot water systems. Replacing a tempering valve has a 2027 estimate of $270 to $520.

Old water heaters can be swapped during the repipe, since the supply is already shut down for the pipe work. Like for like electric storage units have a 2027 estimate of $1,350 to $2,400 supplied and installed. Dux makes Proflo electric storage heaters and Ecosmart heat pumps, while Stiebel Eltron makes single phase electric instantaneous water heaters, which heat water only as it flows. Quantum makes heat pump hot water systems, and Sanden makes the Eco Plus heat pump, which draws warmth from the air to heat water. Business Queensland says solar and heat pump systems must be installed by a hot water installer with a QBCC solar and heat pump endorsement added to their licence. Those options are compared in more depth in our guide to hot water system installation.

Galvin Engineering makes thermostatic mixing valves, which hold outlet temperature steady where tighter control is needed. The QBCC home owner guide suggests having a hot water system serviced every five years by a licensed person. It also says that when a system is replaced or installed, the installation must be brought up to standard. On a repipe quote, check whether the hot water connection is included and which valve will be fitted.

Pressure Testing and Flushing the New Lines

New supply pipes should be tested for leaks before walls, ceilings and trenches are closed. Pressure testing fills the lines and holds them under pressure for a set time while the plumber watches the gauge and checks each joint. Flushing then runs water through the new pipes to clear out debris, shavings and trapped air. Each tap and valve should be opened and checked before the job is signed off. The test should be listed on the quote, and photographed if the walls will be lined straight away.

New copper can affect the water for a short time after installation. Unitywater says copper staining may occur in new houses with new copper pipes and will reduce over time. Redland City Council suggests flushing cold water taps used for drinking and cooking for about two to three minutes after periods without use. That advice is useful after a repipe and after any long absence from the house.

Ask the plumber to photograph the new pipes, joints and clips before linings go back on. Those photos show where each line runs, which saves time if a fitting needs attention later. Copies of the pressure test result, the Form 4 and the product warranty belong in the same folder. Note the position of every new isolation valve, so anyone in the house can shut off one area quickly. Label the main stop tap if it has moved during the work, and show everyone in the household how to use it.

Patching Walls, Ceilings and Tiles Afterwards

The term making good describes putting walls, ceilings, floors and garden beds back in order once the plumbing is done. On a repipe it is a separate cost from the pipe work, so the quote should say who does it. Plumbers may leave cut openings for a plasterer, tiler and painter to close. Check whether the plumber includes patching or only the pipe work, and get separate prices for each trade. Plasterers who patch cut-outs can be found via plaster and gyprock repair services.

Paint is the last layer of making good once the plaster patches have dried. Taubmans makes Endure paint for interior walls and 3 in 1 Prep, a primer, undercoat and sealer for new patches. Wattyl makes the I.D Advanced range, which includes a ceiling paint sold with an anti mould warranty. Matching an old colour can mean repainting a whole wall instead of one patch. Gloss levels matter too, since a new patch in a different sheen can stand out under side lighting. Painters should say whether the price covers a full wall or only the repaired area.

Opening a tiled bathroom wall raises the cost, because waterproofing and tiles must be put back. Mapei, whose Australian base is in Brisbane, makes waterproofing products and tile installation materials. Sika makes liquid applied membranes, waterproofing brushed or rolled on as a liquid, and tile adhesives for the same kind of work. Methven makes shower heads such as the Krome rail shower, and Caroma makes tapware and showers, which some owners replace while a wall is open. Where possible, plumbers can reach bathroom pipes from a hallway or cupboard wall to avoid cutting tiles.

The trades need to follow each other in the right order after a repipe. The plumber finishes and tests the pipes first, then the plasterer closes the openings and sets the joints. Tiling and waterproofing follow in wet areas, and painting comes last once every patch has dried. Booking each trade with a clear start date stops the house sitting open longer than needed.

Keeping Water Running While the Pipes Change

A staged repipe can keep water running in parts of the house while other rooms are worked on. Plumbers can run the new lines beside the old ones and switch each fixture over in turn. The main supply then goes off only for short periods, such as when the new line is joined at the meter end. Request a written plan that shows which rooms will be without water and on which days. Households with babies or anyone who needs daily care should mention it when booking.

Expect dust, noise and open wall cavities while the work is under way. Furniture near cut-in points may need moving, and pets should be kept away from trenches and open ceilings. Drying equipment is sometimes hired when a leak has soaked a floor or wall, at about $50 to $100 a day for an industrial dehumidifier. Confirm whether that hire is included in the quote or charged separately.

Brisbane, the Coasts and Regional Queensland

The repipe ranges in this guide apply across Queensland, but travel and access change the final figure. Plumbers in Brisbane and the larger regional cities treat their own city and nearby suburbs as local work. Properties well beyond the plumber's usual area can attract travel charges between $60 and $250. Staged repipes that need several visits can repeat that fee, so ask whether it applies per visit or once. Local plumbers can be found through our pages on hiring a plumber in Brisbane and Townsville and North Queensland.

Coastal homes are exposed to salt air, which can corrode outdoor taps, exposed fittings and the meter assembly. On the Gold Coast and Sunshine Coast, ask whether outdoor fittings will be replaced along with the pipes. Older inland towns may still have galvanised steel or early copper in original houses. Outside the south east, check whether your council supplies the water and what its concealed leak rules are. Coastal plumbers are listed on our pages for the Gold Coast and the Sunshine Coast.

Rural homes on tank water have a pump, a pressure switch and their own pipe layout. Replacing the house pipes does not include the tank, the pump or the line from the tank unless the quote says so. For pumps and tank connections, see our guide to rainwater tank plumbing. List any tank work as a separate line so each price can be compared.

Rentals, Units and Body Corporate Properties

Tenants in Queensland should report a burst water service or a serious water service leak as an emergency repair. The Residential Tenancies Authority lists both among its emergency repairs, along with a blocked or broken toilet. If the emergency contact cannot be reached in a reasonable time, the tenant or property manager can arrange repairs up to four weeks rent. The tenant must then ask for repayment in writing, with receipts, and allow at least 7 days for payment. Toilet blockages have their own guide on blocked toilet repairs.

In a rental, the owner arranges and pays for a planned repipe. Agree access days with the tenant well ahead, so everyone knows when the water will be off. Owners can combine a repipe with other water upgrades while walls and ceilings are open. Separate rules apply to water fittings in rentals, and landlords can read about them in our rental water efficiency guide. Keep the invoices and the Form 4 with the property records for future tenancies and sale.

In units and townhouses, the pipes may be split between the unit owner, called the lot owner, and the body corporate, the owners' group that manages shared property. Which pipes belong to whom depends on the building and its records, so ask the body corporate manager before booking a plumber. Leaks from a shared pipe may need body corporate approval and their own plumber. Pipes that serve several units can affect neighbours, so shutdowns need notice and planning. Building plans held by the manager may show where the shared lines run. For shared lines, see our guide to body corporate plumbing.

Contracts, Deposits, Warranties and Complaints

Larger repipes can fall under Queensland's domestic building contract rules. The QBCC Consumer Building Guide says the deposit before work starts on site is capped at 10 per cent for a contract under $20,000. For a contract of $20,000 or more, the cap is 5 per cent. On those larger contracts, you may have a cooling-off period, allowing you to withdraw within 5 business days of receiving the signed contract and the guide, though $100 plus reasonable costs may be payable. Ask the plumber whether the job is under a written domestic building contract.

The Queensland Home Warranty Scheme, a QBCC insurance scheme for home building work, can cover residential construction work valued at more than $3,300, including labour, materials and GST. Its policy document, the product disclosure statement, includes items used for primary water supply in its defects cover, but excludes hot water systems. Whether a repipe qualifies depends on the work and the contract, so check with the QBCC before relying on it. The Consumer Building Guide also lists statutory warranties, which the law builds into building contracts, of 6 years for structural defects and 1 year for other defects.

The QBCC takes complaints about plumbing that is unlicensed, defective or not compliant, and about notifiable work with no Form 4. Complaints about plumbing and drainage are lodged online through the QBCC Portal. Contract and payment concerns go through a different QBCC general complaints form. The QBCC can be called on 139 333 for help choosing the right path. Before paying a deposit, search the QBCC register to confirm the plumber's licence is current.

What to Look Out For in a Queensland Repipe Quote

Start by checking that the quote names one pipe system, its maker and the warranty that comes with it. Then count the outlets it reconnects, including outdoor taps, the dishwasher, the fridge line and the water heater. Look for a sketch or written description of the new route through the roof, walls or underfloor, since it shows how much lining will be opened. Patching, tiling, painting and any paving work belong on their own lines, each marked as included or excluded. The quote should state the static pressure, any pressure limiting valve, the pressure test and who registers the Form 4. Without those details, two quotes for the same house cannot be compared fairly.

Treat a recommendation for a whole house repipe after a single leak with caution unless the plumber can show why. Reasonable evidence includes a cut-out section, photos of corrosion or a pattern of earlier repairs. Very low prices sometimes leave out the roof route, the buried line from the meter or the making good. Before signing anything, take the licence number from the quote and search it on the QBCC register.

Checks Before You Sign

Items a full quote includes
One named pipe system and maker, plus the warranty term in writing.
A count of fixtures, appliances and outdoor taps to be reconnected.
The route for new lines through roof, walls, underfloor or slab.
Static pressure measured, and a pressure limiting valve priced if needed.
Pressure testing, flushing and a final check at every outlet.
Who registers the Form 4, and when the owner receives the copy.
Plaster, tiles, paint, paving and lawn listed as included or excluded.
A repipe total that looks cheap may be missing the meter line, the patching or the Form 4. Compare what each quote includes first, then compare the prices.

Getting Repipe Quotes You Can Line Up

Send each plumber the same written brief, so every price covers the same work. State the suburb or town, roughly when the house was built, whether it is highset, lowset or on a slab, and how many bathrooms it has. Attach photos of the meter, the water heater label, any leak and any length of pipe already cut out. Name the water provider on your bill and mention any concealed leak application that is still open. If a pipe has burst, book the repair first and price the wider repipe once the water is under control.

Ask how long each quote stays valid and how soon the work could begin. Prices prepared after the plumber has inspected the roof and underfloor carry less risk of extras than those based only on photos. For areas nobody has inspected yet, ask the plumber to cap the extra hours in writing and state the rate. Compare how many days each plumber needs, because a shorter disruption may be worth a slightly higher total.

Buyers who want to know what they are taking on can have the pipes checked before settlement, the day the sale is finalised. Booking a pre-purchase plumbing inspection lets a plumber note the pipe material, measure the static pressure and look for old leak repairs. Those findings are useful in price talks with the seller and when budgeting for work after moving in. Owners facing a water bill with no clear cause should pay for a leak search before collecting repipe quotes. If water is spraying from a pipe right now, turn off the stop tap at the meter and call an emergency plumber.

Water Pipe Replacement Across Queensland

The 2027 estimates on this page apply across Queensland. Homes close to Brisbane and the regional cities seldom pay a travel charge, while rural properties and outlying towns may pay travel for each visit a staged repipe needs.

▶ Brisbane 31 areas
Brisbane CBD Fortitude Valley New Farm Newstead Teneriffe Paddington Toowong Indooroopilly St Lucia Chapel Hill Kenmore Mount Ommaney Sunnybank Coorparoo Camp Hill Carindale Bulimba Hawthorne Wynnum Manly Chermside Aspley Everton Park The Gap Ashgrove Stafford Nundah Clayfield Hamilton Carseldine Bridgeman Downs
▶ Gold Coast 26 areas
Southport Surfers Paradise Broadbeach Mermaid Beach Miami Burleigh Heads Palm Beach Currumbin Coolangatta Tugun Robina Varsity Lakes Mudgeeraba Nerang Carrara Ashmore Benowa Helensvale Hope Island Coomera Upper Coomera Oxenford Pacific Pines Mount Tamborine Currumbin Valley Ormeau
▶ Sunshine Coast 26 areas
Maroochydore Mooloolaba Alexandra Headland Buderim Sippy Downs Caloundra Golden Beach Currimundi Kawana Waters Coolum Beach Peregian Beach Noosaville Noosa Heads Tewantin Cooroy Pomona Eumundi Nambour Yandina Palmwoods Woombye Maleny Montville Mapleton Beerwah Landsborough
▶ Moreton Bay & Redcliffe 29 areas
Redcliffe Scarborough Margate Woody Point Clontarf Kippa-Ring Rothwell Deception Bay North Lakes Mango Hill Griffin Murrumba Downs Kallangur Petrie Lawnton Strathpine Bray Park Albany Creek Warner Cashmere Samford Dayboro Caboolture Morayfield Burpengary Narangba Bribie Island Woodford Wamuran
▶ Ipswich & Lockyer Valley 28 areas
Ipswich Booval Bundamba Goodna Redbank Springfield Springfield Lakes Brookwater Augustine Heights Ripley Yamanto Raceview Flinders View Karalee Karana Downs Rosewood Marburg Walloon Plainland Hatton Vale Laidley Gatton Forest Hill Withcott Helidon Grandchester Esk Lowood
▶ Logan & Redlands 28 areas
Logan Central Woodridge Kingston Slacks Creek Springwood Daisy Hill Shailer Park Loganholme Loganlea Meadowbrook Beenleigh Eagleby Browns Plains Regents Park Marsden Jimboomba Yarrabilba Cleveland Capalaba Victoria Point Wellington Point Thornlands Alexandra Hills Birkdale Ormiston Redland Bay Mount Cotton Russell Island

Water Pipe Replacement FAQ - Queensland

How much does it cost to repipe a house in Queensland?
A full house repipe in Queensland has a 2027 estimate of $3,000 to more than $15,000, depending on size, storeys and access. A three-bedroom home with open underfloor access sits at $3,000 to $6,000, while a two-storey brick home runs from $8,000 to more than $15,000. Replacing every galvanised steel line has its own range of $3,000 to $10,000. Plaster patching, tiling, painting and any leak search are extra unless a quote lists them. Prices firm up once a plumber has inspected the roof, the underfloor and the meter.
Does replacing water pipes need a Form 4 in Queensland?
Replacing supply pipes in an existing home is notifiable work under the Plumbing and Drainage Regulation 2019. The plumber must register a Form 4 with the QBCC within 10 business days of issuing the invoice. You should receive a copy within 20 business days, and you can check the QBCC online registers to see whether it was lodged. A simple repair to a broken or damaged pipe is minor work and does not need a Form 4.
Who pays to fix the pipe between the meter and my house?
The owner pays for pipes on the property side of the meter in Queensland. Urban Utilities maintains the drinking water service up to the property connection point, and asks customers to use a licensed plumber for leaks on their side of the meter. Unitywater says plumbing problems on private property are the owner's responsibility to investigate and repair. If you are not sure which side of the meter a leak is on, call your water provider before booking a plumber. Urban Utilities takes faults and emergencies on 13 23 64, and Unitywater on 1300 086 489.
Can I get money back on my water bill after a hidden leak?
Water providers in South East Queensland offer concealed leak relief for hidden leaks on the owner's side of the meter. Urban Utilities requires repair by a licensed plumber within one month and an application within six months, with the invoice attached. Unitywater refunds residential customers 70 per cent of the excess water usage charges, or 100 per cent for pensioners. Leaks at taps, toilets, hot water systems and irrigation are excluded by both providers.
What water pressure is allowed inside a Queensland home?
City of Gold Coast cites AS/NZS 3500, the Australian plumbing standard, which limits operating pressure inside a building to 500 kPa, other than at a fire service outlet. Its own network pressure can vary from 220 kPa to around 900 kPa. A pressure limiting valve on the owner's side of the meter brings pressure down, at a 2027 estimate of $150 to $400 installed. Ask the plumber to measure the static pressure before new pipes are connected.
Why does my tap water taste metallic or stain the basin blue-green?
Unitywater says a metallic taste usually indicates iron or copper, and that it is usually caused by corrosion of household copper plumbing. It says copper corrosion can also cause blue-green staining in basins, sinks, showers and toilet bowls. In the short term it advises flushing the affected tap for two minutes. In the longer term, a licensed plumber should inspect the pipes for corrosion and replace them if required.
Should I repair one leak or repipe the whole house?
One leak caused by damage, such as a nail or a loose clip, is a repair job priced as a section. Repeated leaks in the same material, narrowed galvanised pipe or corrosion at several outlets are reasons to price a zone or full repipe. An accessible copper repair has a 2027 estimate of $250 to $600, while a full repipe starts at $3,000. Ask for both prices in writing so the choice is based on facts. If the walls are already open for a renovation, replacing the pipes then avoids opening them again.
Which pipe should be used for a Queensland repipe?
Copper, PE-X and polyethylene are all used for water supply in Queensland homes. Copper is rigid and joined by soldering or press fittings, while PE-X is a flexible plastic pipe that needs fewer joints. Polyethylene, known as poly pipe, is used for buried lines such as the run from the meter. Whatever is chosen, the quote should name one system and its maker so prices can be compared. Buried lines from the meter can use polyethylene even when the house itself is repiped in copper or PE-X.
Does a new hot water system need a tempering valve?
Business Queensland says a temperature control device must be fitted to all new and replacement hot water systems. Stored water must reach at least 60°C, and water should reach taps at no more than 50°C. Replacing a tempering valve has a 2027 estimate of $270 to $520. Installing or replacing a water heater or temperature control device is notifiable work, so a Form 4 follows.
Who fixes a burst water pipe in a rental property?
The Residential Tenancies Authority lists a burst water service or a serious water service leak as an emergency repair. Tenants should contact the emergency contact in the tenancy agreement as soon as possible. If that contact cannot be reached in a reasonable time, the tenant or property manager can arrange repairs up to four weeks rent. The tenant then asks for repayment in writing with receipts and allows at least 7 days for payment. A planned repipe of the whole property remains the owner's decision and cost.

Specialists for Queensland Pipe Work

For Trades & Contractors - QLD

Queensland plumbers who replace water services and repipe homes can browse open work on the QLD job leads board, along with plumber jobs in Queensland and leak detection jobs.

Compare Queensland Repipe Quotes

Describe the house, the pipe material and the leaks so far, then compare quotes from licensed Queensland plumbers who are all pricing the same repair or repipe.

Get Free Pipe Replacement Quotes

About This Guide

This page provides guidance information only. Details may change, always verify with the relevant authorities and seek independent professional advice where needed.

Reviewed by The Quote Yard Editorial Team

Published 19 November 2026 ·

How The Quote Yard Works

We connect you with independent local tradies and service providers, we don't perform any trade work ourselves. Tradies provide their own quotes directly to you. Always confirm licensing, insurance, and scope of work before engaging any provider.

All Queensland tradies are required to hold appropriate QBCC licences. Verify at the Queensland Building and Construction Commission.
Prices are 2027 estimates for licensed water pipe work in Queensland. They exclude leak searches, plaster patching, tiling, painting and outdoor restoration unless a quote lists them.
Need work done? Get free quotes. Post a Job – It's Free