Looking for an Air Conditioning Installer in Melbourne?

Tell us your suburb, whether the home is a house, townhouse or apartment, which rooms you want heated or cooled, and where the outdoor unit could go. Mention any gas heater being replaced, and say if the street has heritage controls or the building has an owners corporation. We will pass that description to local installers across Melbourne, so every quote prices the same job.

Get Free Air Conditioning Quotes

Melbourne Air Conditioning Price Guide

Split system, 2.0 to 2.5 kW, supplied and installed$1,200 - $2,000
Split system, 3.5 kW, supplied and installed$1,600 - $2,600
Split system, 5 to 6 kW, supplied and installed$2,200 - $3,500
Split system, 7 to 8 kW, supplied and installed$3,200 - $4,800
Back to back split (units either side of one wall), labour only$600 - $900
Multi-split, three indoor units$6,500 - $10,000
Ducted reverse cycle, three bedroom house$9,000 - $18,000
Extra pipe beyond the included length$60 - $120 per metre
Dedicated power circuit$250 - $600
Old unit removal and gas recovery$150 - $400

These are 2027 estimates for air conditioning work across metropolitan Melbourne. Your price depends on the unit size and model, the length of pipe between the indoor and outdoor units, access at height, and whether the switchboard needs electrical work.

Hire an Air Conditioning Installer Melbourne VIC - Get Local Quotes

Melbourne air conditioning jobs range from one split system, an indoor wall unit piped to an outdoor unit, to a ducted system replacing gas heating across a whole house. In Victoria, connecting pipes for refrigerant, the gas that carries heat, is plumbing work, so installers need a plumbing registration or licence in the right class from the Building and Plumbing Commission. The same person also needs a refrigerant handling licence from the Australian Refrigeration Council, and the wiring must be done by a licensed electrician. Each trade should certify its work in writing, such as with a plumbing compliance certificate and a Certificate of Electrical Safety. Apartment owners usually need approval from the owners corporation, the owners' group running the building, before an outdoor unit goes on a balcony, roof or wall. Houses under a heritage overlay, a council control on older streets, may need a planning permit for an outdoor unit seen from the street. The Victorian Energy Upgrades program can cut the price of an approved reverse cycle system, but only through an accredited provider, a program-approved business, before work starts. Rental homes face new heating and cooling standards from 1 March 2027. Ducted systems need roof access, outlets in each room and often a new switchboard circuit. A licensed gasfitter must disconnect any old gas heater. Prices on this page are 2027 estimates for metropolitan Melbourne. Post your job on The Quote Yard and we will connect you with local Melbourne installers who can quote on it.

Melbourne Air Conditioning Work Covered

Air conditioning work across Melbourne ranges from a single split system in an inner city apartment to ducted reverse cycle systems replacing gas heating in suburban houses. We can connect you with local installers who all price the same written description of your job.

Get Free Quotes

At a Glance - Melbourne Air Conditioning Installs, 2027 Estimates

Job Price Range How It Is Charged What Drives It In Melbourne Who Can Do It
Bedroom split, 2.0 to 2.5 kW $1,200 - $2,000 Supplied and installed Pipe length and wall type RAC plumber with ARC licence, plus electrician
Living room split, 5 to 6 kW $2,200 - $3,500 Supplied and installed Model and outdoor position RAC plumber with ARC licence, plus electrician
Open plan split, 7 to 8 kW $3,200 - $4,800 Supplied and installed Capacity and access RAC plumber with ARC licence, plus electrician
Back to back split, labour $600 - $900 Fixed price Wall material and height Plumber in the split system or full air conditioning class
Multi-split, two indoor units $4,500 - $7,000 Supplied and installed Pipe length to each room RAC plumber with ARC licence, plus electrician
Multi-split, four indoor units $8,500 - $13,000 Supplied and installed Apartment access and approvals RAC plumber with ARC licence, plus electrician
Ceiling cassette $3,500 - $6,500 Supplied and installed Ceiling framing and roof space RAC plumber with ARC licence, plus electrician
Ducted, home up to 150 m² $8,000 - $13,000 Quoted after a site visit Roof space height and outlets RAC plumber with ARC licence, plus electrician
Ducted, home 150 to 250 m² $12,000 - $18,000 Quoted after a site visit Zones and duct runs RAC plumber with ARC licence, plus electrician
Zone control add-on $2,000 - $4,500 Per system Number of zones Installer and electrician
Ducted changeover, ducts kept $6,000 - $11,000 Supplied and installed Condition of old ducts RAC plumber with ARC licence, plus electrician
Switchboard upgrade $800 - $2,500 Fixed after inspection Board age and space Licensed electrician
Old unit removal and gas recovery $150 - $400 Per unit Height and access Technician with an ARC refrigerant licence

What Pushes a Melbourne Air Conditioning Bill Up

What is involved
Long pipes to a hidden outdoor position add about $60 to $120 for every metre beyond the included length.
Older switchboards with no spare room or no safety switches, which cut power when there is a fault, can add $800 to $2,500 before the system is connected.
Two storey homes, roof mounted units and tight roof spaces add access charges and extra labour time.
Gas heater disconnection, asbestos checks and owners corporation conditions can each add a separate cost.
Ask every installer to list the unit models, pipe length, electrical work, removal of any old unit and any gas disconnection on separate lines, so the quotes can be compared item by item.

Choosing Who Installs Air Conditioning in a Melbourne Home

Melbourne households usually call an air conditioning installer for one of three jobs: a new split system, a multi-room or ducted system, or the replacement of an old heater. A single split system, one indoor wall unit piped to one outdoor unit, is the most common request for a bedroom or living area, and it is often finished in one day. Ducted reverse cycle systems, which heat and cool the whole house through hidden ducts, take longer, because the indoor unit sits in the roof space and every room needs ducts and ceiling outlets. For an overview of what installers include, see our Victorian air conditioning installation guide. Hiring in Melbourne also brings its own licences, certificates and rules for apartments, heritage streets, rentals and night time noise.

Businesses offering this work range from technicians working on their own who fit split systems to companies with crews for ducted systems, roof work and wiring. In Victoria the person who connects the refrigerant pipes, which carry the heat-moving gas, must hold a plumbing registration or licence in an air conditioning class and a national refrigerant licence. The wiring is a separate licensed job, which some installers hold themselves and others hand to an electrician. Ask early whether the person quoting will also do the install, since some businesses pass jobs to subcontractors. Knowing which licence covers which part of the job makes it much easier to read a quote and check the business behind it.

What Split, Multi-Split and Ducted Systems Cost in 2027

The figures on this page are 2027 estimates for metropolitan Melbourne, taken from the Quote Yard's Victorian pricing guides. A small split system of 2.0 to 2.5 kilowatts (kW), the usual size for a bedroom or study, costs about $1,200 to $2,000 supplied and installed. A 3.5 kW unit runs at about $1,600 to $2,600, and a 5 to 6 kW unit for a medium living area at about $2,200 to $3,500. Large open plan rooms that need 7 to 8 kW cost around $3,200 to $4,800, while units of 9 kW or more start at about $4,000. Kilowatts describe the unit's heating or cooling output, not its power use, so a bigger number means more capacity. Room by room sizing is set out in the split system installation guide.

Multi-split systems connect several indoor units to one outdoor unit, which suits apartments and townhouses with little space outside. A two head system, meaning two indoor units, costs about $4,500 to $7,000, a three head system about $6,500 to $10,000 and a four head system about $8,500 to $13,000. Ducted reverse cycle systems for a small home of up to 150 square metres cost about $8,000 to $13,000, rising to $12,000 to $18,000 for a medium home. Larger homes over 250 square metres can reach $16,000 to $28,000 or more. Ceiling cassette units, which sit flush in the ceiling and spread air in several directions, cost about $3,500 to $6,500 installed. The full comparison across system types is in the Victorian air conditioning cost guide.

Daikin makes wall split systems such as the Zena range. Mitsubishi Electric makes wall mounted, floor console, ducted and multi head split systems. Panasonic makes single room wall units and multi room systems that run several indoor units from one outdoor unit. Samsung makes split systems, ducted systems and a round ceiling unit it calls the 360 Cassette. LG makes split, multi split and ducted systems for homes. Brand choice changes the unit price, but the labour, pipe length and electrical work often explain most of the difference between two quotes.

Melbourne Area 5 kW Split, Installed Ducted, Three Bedrooms Split Install Labour
Inner Melbourne and CBD $1,900 - $3,200 $11,000 - $18,000 $900 - $1,900
Northern suburbs $1,600 - $2,600 $9,000 - $15,000 $700 - $1,400
Eastern suburbs $1,750 - $2,900 $10,000 - $16,500 $800 - $1,600
Western suburbs $1,600 - $2,600 $9,000 - $15,000 $700 - $1,400
South eastern suburbs $1,700 - $2,800 $9,500 - $15,800 $750 - $1,500

Suburb Differences and the Extras Added After a Site Visit

Installation labour varies across Melbourne, mostly because of access, parking, building age and travel time. Labour to install a split system runs at about $900 to $1,900 in inner Melbourne and the CBD, compared with about $700 to $1,400 in the northern and western suburbs. Ducted installation labour follows the same pattern, at about $4,500 to $8,000 in inner areas and $3,600 to $6,500 in the north and west. Inner city jobs often involve apartments, narrow terraces, shared walls and tight roof spaces, which all take longer. Limited street parking near inner city apartments can also slow the delivery of units and equipment on install day.

Most advertised prices include a standard installation with three to five metres of pipe between the indoor and outdoor units. A back to back install, where the two units sit on opposite sides of one wall, costs about $600 to $900 in labour. Each extra metre costs about $60 to $120, so moving the outdoor unit to a hidden spot can add several hundred dollars. A dedicated power circuit, a separate line from the switchboard for the air conditioner alone, costs about $250 to $600, and a switchboard upgrade about $800 to $2,500 if the old board has no room. Roof or height access adds about $200 to $900, and a pad or wall brackets for the outdoor unit about $150 to $450. A Melbourne concreter can pour a proper slab if the unit is going on bare ground beside the house.

Bulkheads are boxed sections of ceiling that hide ducts or an indoor unit, and they cost about $80 to $180 per linear metre. Zone control, which lets you heat or cool parts of the house separately, adds about $2,000 to $4,500 to a ducted system. Cassette indoor units on a multi-split system add about $500 to $1,200 each compared with wall units. Ask every installer to list these items separately, so you can see what the advertised price leaves out.

Extras That Often Appear on a Melbourne Quote

Extra item
Estimated cost
Pipe beyond the included 3 to 5 m
$60 - $120 per metre
Dedicated power circuit
$250 - $600
Roof or height access
$200 - $900
Outdoor unit pad or brackets
$150 - $450
Bulkhead to hide ducts
$80 - $180 per linear metre
Ceiling outlet added to ducted
$120 - $300 each

Pipework replacement on a changeover costs about $400 to $1,200 when the old pipes cannot be reused.

Gas heater disconnection by a gasfitter is priced on quote.

If a quote shows one total with no extras listed, ask what pipe length, electrical work and access it allows for.

Plumbing Classes and Refrigerant Licences for Victorian Installs

Victoria treats the refrigerant side of an air conditioning job as plumbing work, so the Building and Plumbing Commission (BPC) registers and licenses the people who do it. Under the Plumbing Regulations 2018, the refrigerated air conditioning (RAC) class covers equipment used to heat or cool a building. That includes the ductwork, roof sheeting and flashing, the metal strips that seal gaps around pipes, needed for the job. A restricted class, a narrower licence for set tasks, covers single head split systems up to 18 kW of cooling, ceiling cassette systems and add-on outdoor units for ducted systems. You can check a plumber's registration and class with the Building and Plumbing Commission before you sign anything.

Other restricted classes cover narrower tasks, such as duct fixing, so ask which class the person on your job holds. A multi-split system falls outside the restricted single head list, so it needs an installer with the full RAC class. Any plumbing work worth $750 or more, counting labour, materials and appliances, needs a plumbing compliance certificate, the plumber's written statement that the work meets plumbing standards. That certificate must go to the person who asked for the work, generally within five days of completion. The plumber must also carry insurance for certificate work, with at least $50,000 of cover per claim for domestic jobs. Keep the certificate with the house records, because it shows the work was done by a registered or licensed plumber.

On top of the plumbing class, anyone who handles refrigerant gas needs a licence from the Australian Refrigeration Council (ARC), which runs the national scheme. The full RAC01 licence covers refrigeration and air conditioning work in general. The restricted RSS03 licence covers installing and decommissioning single head split systems under 18 kW, along with some heat pump water heaters. The RDR04 licence, a restricted licence for domestic appliances, does not cover split systems at all, so it is not enough for your job. The licence type is shown on the technician's ARC licence, so ask to see it at the site visit.

Businesses that buy and handle refrigerant also need a trading authorisation, a permit to buy and store the gas, and both can be checked through the Australian Refrigeration Council Look for the Tick search. Decommissioning means safely shutting down an old unit and recovering its refrigerant gas instead of releasing it. Removal and degassing of an old split system costs about $150 to $400, depending on height and access. Testo makes heating, ventilation and air conditioning (HVAC) measuring instruments, including compact tools that connect to a smartphone.

Part of the Job Who Does It Licence or Class Document You Receive
Single head split up to 18 kW Plumber in the RAC class or restricted split system class BPC plumbing registration or licence Compliance certificate at $750 or more
Multi-split or full ducted system Plumber in the full RAC class BPC plumbing registration or licence Compliance certificate
Handling refrigerant gas Technician with an ARC licence RAC01, or RSS03 for single head splits Licence number on the paperwork
New circuit or switchboard work Licensed electrician from a registered contractor Energy Safe Victoria licence Certificate of Electrical Safety
Like for like swap, same cables Holder of a restricted electrical licence Refrigeration and air conditioning class Certificate of Electrical Safety
Gas heater disconnection Licensed gasfitter BPC gasfitting class Compliance certificate for gas work

Energy Safe Victoria Rules for the Wiring Side of the Job

Energy Safe Victoria regulates electrical work, and it tells householders to engage a registered electrical contractor, a business registered for electrical work, who sends a licensed electrician. A new air conditioner usually needs its own circuit from the switchboard, and older Melbourne switchboards may lack spare room or safety switches. Some installers hold an electrical licence themselves, while others bring in a Melbourne electrician for the circuit work. Some installers hold a restricted electrical licence in the refrigeration and air conditioning class, which only covers swapping a unit for one of the same power, in the same spot, using the existing cables. Anything beyond that, such as a new circuit or a longer cable run, needs a fully licensed electrician.

Air conditioning wiring is classed as non-prescribed electrical work, the everyday category, so it needs no independent inspection before it is switched on. The electrician must still give you a Certificate of Electrical Safety (COES), a legal record of the work, within 30 days. Work on the main switchboard is prescribed work, the higher risk category, which a licensed electrical inspector must check before it is switched on. Ask whether your job includes a switchboard upgrade, and allow time for that inspection in the schedule. Until the inspection is passed, the new board cannot be switched on, so the air conditioner cannot run on it either.

You can search Energy Safe Victoria records to see whether an electronic COES exists for your address. If the electrician will not show a licence, or no certificate arrives, Energy Safe Victoria asks you to contact it straight away. Keep the COES with the plumbing compliance certificate, because a buyer or insurer may ask for both later. Energy Safe Victoria also warns that doing your own electrical work is illegal and can be deadly.

Electrical Paperwork on a Melbourne Install

30 days, the time an electrician has to give you a copy of the COES for non-prescribed work such as air conditioning
Electrical work
What applies
New air conditioning circuit
Non-prescribed, no inspection, COES required
Main switchboard work
Prescribed, inspected before it is switched on
Like for like swap
Restricted licence holder may do it
Any certified work
COES searchable by address

A COES can only be issued by electrical workers registered or licensed by Energy Safe Victoria.

Keep the COES with the plumbing certificate for future sales and insurance claims.

An installer who says no electrical certificate is needed for a new circuit is wrong, so ask who will issue the COES before work starts.

Single Trade Jobs, Written Quotes and Larger Renovations

Consumer Affairs Victoria says a domestic building contract is not required for a job that involves only one trade, such as plumbing or electrical work. A straight air conditioning install is usually handled as plumbing work with an electrical connection, rather than as a building project. The same guidance still says a written contract is essential for all building work, whatever its size or price. If air conditioning is part of a renovation with more than one trade worth over $10,000, you need a major domestic building contract, a formal contract with terms set by law, before work starts. Guidance on how those contracts work, and what they must contain, is published by Consumer Affairs Victoria.

For a standard install, the written quote often becomes the contract, so it should name the exact indoor and outdoor models. It should also state the pipe length included, the circuit work, the outdoor position, the removal of any old unit and the payment terms. Ask how much is due before work starts, and hold the balance until the system is commissioned and both certificates have arrived. Commissioning is the final testing step, where the installer checks the system runs correctly in heating and cooling modes.

Which Paperwork Fits Which Job

Type of job
What to have in writing
Split or multi-split install only
Detailed written quote naming the models
Install inside a larger renovation
Major domestic building contract over $10,000
Gas heater removed with the install
Gasfitter's compliance certificate
System bought with a VEU discount
Accredited provider's quote showing the discount

A written quote that lists every item protects both sides if a dispute arises later.

Payment terms should follow finished stages, not dates on a calendar.

A large deposit on a simple split system install is a warning sign, so keep most of the money until the system is running.

Claiming a Victorian Energy Upgrades Discount Before Work Starts

The Victorian Energy Upgrades (VEU) program gives discounts on approved high efficiency reverse cycle air conditioners. Reverse cycle means the same system both heats and cools, which is why it is promoted as a replacement for gas heating. Households replacing a non-ducted gas room heater with a 3 to 9 kW system can receive a discount of up to $1,610. Replacing a ducted gas heater can attract up to $2,940 for a multi-split system and up to $5,530 for a 22.4 kW ducted unit. Current amounts and conditions are published on the Victorian Government energy website, and they can change.

The discount must go through an accredited provider, a business approved under the program, or an installer working with one. If you want to use your own installer, they need to arrange this with an accredited provider before any work starts. The program says discounts typically cannot be applied after the work is done, so a system installed first and claimed later is unlikely to qualify. The product must be approved under the program and carry at least a five year warranty for homes. Where an existing system is being replaced, the property must be more than two years old. Private rentals can also qualify, and the program suggests landlords and renters work together on the upgrade.

Only products on the program's approved list qualify, so the model you choose affects whether a discount applies at all. Ask the accredited provider to show the approved model, the discount amount and the heater being replaced on the written quote. The program describes the discount as part of the provider's quote, not as a refund paid to you afterwards. Keep that paperwork, because it records which heater was decommissioned and which system replaced it.

Heater Being Replaced New System Discount Up To
Non-ducted gas room heater Reverse cycle, 3 to 9 kW Up to $1,610
Ducted gas heater Multi-split system Up to $2,940
Ducted gas heater 22.4 kW ducted reverse cycle Up to $5,530
Electric resistance or older reverse cycle Approved reverse cycle system Varies by product

Retiring a Gas Wall Furnace or Ducted Gas Heater

Many Melbourne houses still run a gas wall furnace, a heater set into a living room wall, or a ducted gas heater under the floor or in the roof. Replacing either with reverse cycle air conditioning involves two licensed jobs: disconnecting the gas appliance and installing the new system. Disconnecting a gas appliance is gasfitting, and work on gas appliances or gas piping needs a compliance certificate regardless of the price. Some air conditioning businesses employ a gasfitter, while others leave that part to you or to a Victorian gasfitter. The gas disconnection is priced on quote, so make sure one quote includes it or book it separately. Ask for the gasfitter's licence number too, and check it with the BPC before the work is booked.

Brivis makes ducted gas heaters and evaporative coolers, so its name may appear on the old unit being removed. Existing ducts from a gas heater are sometimes reused for a ducted reverse cycle system, but old floor and roof ducts are not always suitable. A ducted changeover that keeps the existing ductwork costs about $6,000 to $11,000, while new ductwork takes it to about $10,000 to $22,000. Polyaire makes flexible duct, AirTouch zoning controllers and ceiling grilles that installers fit when ducts are replaced. Whether old ducts can stay is discussed in the guide to air conditioning replacement and upgrades.

ActronAir makes ducted and wall mounted systems, along with NEO controls that offer individual zoning of rooms. Temperzone makes ducted split systems and has local factories in Australia and New Zealand. Rinnai makes inverter split systems, multi split systems and ducted reverse cycle systems for whole homes. An inverter varies the compressor speed, so the system runs steadily instead of switching fully on and off.

Before the Gas Heater Comes Out

Situation
What to arrange
Gas wall furnace in the lounge
Licensed gasfitter disconnects and certifies
Ducted gas heater
Check whether the ducts can be reused
Heater flue, or exhaust pipe, through the roof
Agree who removes it and seals the roof
VEU discount wanted
Accredited provider booked before removal

Book the gasfitter and the installer for the same week, so the house is not left without heating for long.

Keep the old heater details for the VEU paperwork.

Never let anyone seal off a gas pipe without a compliance certificate, because all gas appliance work needs one.

Rental Homes and the 1 March 2027 Heating and Cooling Standards

New minimum energy efficiency standards for Victorian rental homes start in March 2027. From 1 March 2027, when a rental's existing heater fails and cannot be repaired, it must be replaced with fixed efficient electric heating. In practice that means a reverse cycle air conditioner with an outlet in the main living area. Fixed means the system is permanently installed, not a portable unit that plugs into a power point. A cooling standard also requires a reverse cycle system in the main living area at the start of a new lease, or a move to a month to month periodic lease, from 1 March 2027. From 1 July 2030, the cooling requirement applies whether or not a new lease has been signed.

Rental providers, the Victorian term for landlords, should ask for a quote that shows the indoor unit's position in the main living area. A rental property may also qualify for the VEU discount, which can lower the cost of a system that meets the standard. Renters should not book an install themselves without the rental provider's written agreement, since the system stays with the property and involves holes in walls. Access times for the site visit and install day should be agreed with the renter well in advance. Property managers can ask installers to hand over the warranty documents and both certificates when the job is finished.

Rental homes in apartment buildings still need owners corporation approval for an outdoor unit, so rental providers should start that process early. A multi-split system can serve the main living area and bedrooms from one outdoor unit where balcony space is tight. Installers should confirm the indoor unit position in writing, because the standards name the main living area specifically. Booking the work before an old heater fails avoids a rushed replacement at a time when the home has no working heater.

Date and Trigger Requirement What It Means for the Install
1 March 2027, heater fails and cannot be repaired Reverse cycle heating with an outlet in the main living area Replace the failed heater with a fixed system
1 March 2027, new lease or move to a periodic lease Reverse cycle cooling in the main living area Install before the new lease starts
1 July 2030 Cooling standard applies with or without a new lease Plan installs for remaining rentals early
Portable or plug-in unit Not a fixed system Choose a fixed reverse cycle system

Air Conditioners on Apartment Balconies and Rooftops

An owners corporation is the body, made up of all the owners, that manages the shared parts of an apartment or unit complex. Its rules can require an owner to get prior written approval before altering the building structure or exterior. Owners corporation rules can also cover the maintenance of air conditioners and noise from them. An owner must not repair, alter or maintain common property unless the owners corporation has expressly authorised it. Common property is the shared part of the building, such as external walls, roofs and corridors, which often includes the wall where the outdoor unit would go.

Before you collect quotes, ask the building manager or owners corporation for its rules and any approval form for air conditioning. Approval requests usually need the unit model, its position, how pipes and cables will run and where the condensate drain goes. Condensate is the water an air conditioner pulls out of the air, and the drain is the small pipe that carries it away. Get the approval in writing before paying a deposit, because a refusal after the install can mean moving the unit at your cost.

The BPC's split system guidance says condensate drains must end at a safe and visible point that avoids damage to the building. Drains should not run over a balcony edge where they cause a nuisance, and should empty into the sewer or stormwater system instead. Outdoor units on a balcony should not sit close to the balustrade, the railing or low wall at the edge, because children could climb on them. On metal sheet roofs, the guidance says timber supports for a unit must not sit in the flat channels where rainwater runs. Multi-split options for apartments are compared in the multi-split installation guide.

Item What the BPC Guidance Says What to Ask the Installer
Condensate drain Safe, visible end point that avoids damage Where the drain connects
Balcony edge No discharge over the edge if it causes nuisance Drain to sewer or stormwater
Unit near a balustrade Not close, as children could climb it Distance from the balustrade
Unit mounting Level, on a bracket or base and tied down Bracket or pad type
Metal deck roof No timber supports in the roof channels Roof support method
Pipe insulation Must fully enclose the refrigerant pipe Insulation on the full run

Permit Triggers for Units Seen From the Street on Heritage Houses

A heritage overlay is a planning control that protects older buildings and streets of heritage value, and many inner Melbourne streets have one. Under a heritage overlay, a planning permit is needed to install household equipment if it is visible from a street, other than a lane, or a public park. The City of Port Phillip lists air conditioning units among the external service units that need a permit when visible in that way. The City of Melbourne explains that a heritage place appears on the planning scheme map with a reference number, such as HO21. Your planning property report, a free online summary of the planning rules for your address, shows whether an overlay applies.

Port Phillip's guidance says outdoor units must not be placed on or in front of the front facade, the main street-facing wall, of a house. It discourages rooftop and other highly visible positions and prefers ground level spots that can be screened with shrubs. Connecting cables should pass through the wall at a low level where possible, with any exposed run hidden in a painted duct cover. Because pipes can run up to 30 metres, the outdoor unit can often sit in a side passage or rear yard instead. Remember that every extra metre of pipe beyond the included run adds to the price. Ask the installer to mark the planned pipe route on a photo, so you and the council can see exactly what is proposed.

Other councils set their own heritage controls, so ask your council's planning department before buying a unit for a heritage house. Free advice may be on offer, as Port Phillip provides placement help through its sustainable design officer. Heritage guidance also warns against blocking windows or damaging original wall vents when choosing a position. Include the council's answer in the job description you send to installers, so every quote assumes the same unit position.

Placing a Unit on a Heritage House

Position
How heritage guidance treats it
On or in front of the front facade
Not allowed under Port Phillip guidance
On the roof
Strongly discouraged
Ground level, screened by shrubs
Preferred
Visible only from a rear lane
Lane views alone do not trigger the permit

Corner sites need extra care, because the side street is also a street frontage.

Paint exposed duct covers to blend with the wall.

Ask your council before buying the unit, because the permit question can change where it goes and how much pipe the job needs.

EPA Victoria Night Hours for Running an Air Conditioner

Residential noise in Victoria is controlled through prohibited times set by EPA Victoria. An air conditioner used for cooling should not be heard in a neighbour's habitable room, meaning a living space such as a bedroom or lounge, on weekdays before 7 am or after 11 pm. On weekends and public holidays, the cooling restriction runs from 11 pm until 9 am the next morning. Air conditioners used for heating, and heat pumps, fall into a different group with the evening cut off at 10 pm instead. A garage or laundry next door does not count as a habitable room.

During a heat health warning, an official public health alert from the Victorian Department of Health, EPA Victoria says you can use your air conditioner for cooling at any time. Noise is unreasonable when it occurs during prohibited times and someone in a habitable room of another home can hear it. The EPA does not investigate residential noise, so complaints go to the local council. Placement matters most on narrow blocks, where the outdoor unit may sit close to a neighbour's bedroom window. Inner suburban terraces with shared side walls and small courtyards leave few positions far from the house next door.

Ask installers to include the outdoor unit's published sound level in their quote, so you can compare models. Mitsubishi Heavy Industries makes split, ducted and multi-split systems, including the Ciara wall split range. Toshiba makes single split, multi split, inverter ducted and ceiling cassette systems. Comparing the published sound figures for similar models is more useful than relying on a brand name. If the only workable position faces a neighbour's window, ask whether a different wall or a sound-blocking screen is possible. Brackets fixed to a shared wall can carry vibration into the next house, so ask whether a concrete pad on the ground would suit better.

Use Weekdays Weekends and Public Holidays Exception or Note
Cooling Before 7 am and after 11 pm Before 9 am and after 11 pm Any time during a heat health warning
Heating, including heat pumps Before 7 am and after 10 pm Before 9 am and after 10 pm Council handles complaints

Asbestos Cement Eaves and Fibro Where Pipes Pass Through

Many Melbourne houses built before 1990 contain asbestos cement, sheeting made with asbestos fibres, especially in the eaves, the roof overhang above the outside walls, and in wall cladding and bathroom and laundry ceilings. Air conditioning installs often drill through exactly those materials, for pipe holes, cable runs and roof access. Victoria's official asbestos guidance says that if a suspect material was installed before 1990, it is safest to assume it contains asbestos. Testing gives certainty, and asbestos testing and inspection can be booked before the installer arrives. The Victorian asbestos website explains where the material is found and how to identify it safely.

Tell each installer the year your house was built and point out any fibro sheeting where pipes would pass. Fibro is the common name for flat or ribbed cement sheeting used on older houses for eaves, walls and ceilings. An installer may suggest another pipe route, such as through brickwork or a newer wall, to avoid disturbing it. Holes left in plaster when an old unit is moved can be patched by a Melbourne plasterer. Where pipes must pass through a tiled wall or balcony, a Melbourne tiler can replace any cracked tiles.

Ducted installs need safe access to the roof space, where installers may also find old insulation, loose cables or signs of rodents. A Melbourne pest controller can deal with rats or mice before new ducts and cables go in. Roofs with a shallow slope leave little room for a ducted indoor unit, which can push the job toward a multi-split system. Where ceiling insulation is missing or disturbed, ceiling insulation installation can follow once the ducts are in place.

Before Anyone Drills or Climbs Into the Roof

Check
Why it matters
Year the house was built
Pre-1990 materials may contain asbestos
Eaves and wall sheeting
Common places for asbestos cement
Roof space condition
Rodent damage and old cables need attention
Insulation in the roof
May need replacing after ducts go in

Testing a sample before work starts is far simpler than dealing with a disturbed sheet afterwards.

Choose a pipe route through brick where possible.

If an installer starts cutting suspect sheeting without checking, stop the work and arrange testing.

Warranty Registration, Servicing and the Install Paperwork

Two certificates should arrive after a typical Melbourne install, one for the plumbing side and one for the electrical side. The plumbing compliance certificate covers the refrigerant installation when the work is worth $750 or more. The Certificate of Electrical Safety covers the new circuit or connection, and it should reach you within 30 days. If a gas heater was disconnected, the gasfitter's compliance certificate is a third document to keep. Ask for the ARC licence number of the technician who handled the refrigerant, and file it with the others.

Read the warranty terms, because some manufacturers set conditions about who installs the system and when it must be registered. Register the system as soon as it is running, and keep the invoice that shows the installation date. Book regular cleaning and checks through air conditioning servicing, and keep each service record with the certificates. Annual servicing of a multi-head system costs about $200 to $400. Clean the indoor filters as often as the owner's manual directs, especially during long runs of heating or cooling. Keep the outdoor unit clear of leaves, pot plants and stored items, so air can flow freely around it.

Item Who Provides It Why It Matters
Plumbing compliance certificate Plumber Proof the refrigerant work meets plumbing standards
Certificate of Electrical Safety Electrician Legal record of the electrical work
Gasfitter's compliance certificate Gasfitter Shows the old heater was safely disconnected
ARC licence number Installer Lets you check who handled the refrigerant
Warranty registration Owner or installer Keeps manufacturer cover in place
Owners corporation approval Owners corporation Shows the unit position was approved
VEU paperwork Accredited provider Confirms the discount was applied

Faults, Refunds and Where to Take a Complaint

Start with the business that sold or installed the system, in writing, with photos, dates and the model numbers. Keep copies of every message, because they form the record if the matter goes any further. Under the Australian Consumer Law, services must be done with acceptable care and skill and do the job you told the business you needed. Products must be of acceptable quality, and these consumer guarantees apply automatically on top of any manufacturer's warranty. A business cannot refuse to help by telling you to contact the manufacturer instead. Remedies described by the ACCC can include repair, replacement, refund, cancellation or compensation.

Faulty plumbing work, such as leaking condensate drains or poor pipe insulation, should be raised with the plumber and then with the BPC. The plumber's insurance covers fixing defective work, and unfinished work where the plumber has died, disappeared or become insolvent, meaning unable to pay their debts. Electrical concerns, including a missing COES, go to Energy Safe Victoria. Consumer Affairs Victoria can advise on contract disputes, and claims that stay unresolved can go to a tribunal.

What to Look Out For in Licences, Models and Discounts

A quote that names no models makes it impossible to compare prices, sound levels or warranties. Look for a plumbing registration or licence number, an ARC licence or authorisation, and a named electrician or electrical licence. Be wary of a price that shows no pipe length, no circuit work and no plan for draining the condensate. Offers of free or nearly free systems deserve care, because VEU discounts only flow through accredited providers with set conditions. Check that nobody plans to claim a discount after the install, since claims made after the work are typically not possible. Insist on the quote in writing, even for a small job, so every promise made at the site visit is recorded.

Ask who removes the old unit and recovers its gas, as some quotes leave this out. Check whether the installer has allowed for roof or height access, which can add several hundred dollars on a two storey home. For apartments, the quote should say the work depends on owners corporation approval. For heritage houses, it should show the agreed unit position and allow for any extra pipe.

Red Flags on a Melbourne Air Conditioning Quote

On the quote
Why it matters
No plumbing registration number
Refrigerant work in Victoria is plumbing work
No ARC licence
Only licensed technicians may handle refrigerant
No models named
You cannot compare price, sound or warranty
Discount promised after install
VEU discounts are applied before work starts

A quote with no electrical line may leave you to find and pay an electrician later.

A price far below the others may leave out pipe, circuit work or removal of the old unit.

If an installer cannot name the person who will sign the plumbing certificate and the COES, keep looking.

Getting Air Conditioning Quotes Built on One Room List

Comparable quotes start with every installer pricing the same rooms, the same unit sizes and the same outdoor position. Send each one your suburb, the type of home, the rooms to be heated or cooled and rough room measurements. Add photos of the inside wall for each indoor unit, the outdoor spot, the switchboard and any existing heater. Note whether you live in an apartment, a heritage overlay or a rental, because each changes the approvals needed. If you are unsure about the system type, ask for prices on two options, such as separate split systems and a multi-split.

Ask for each quote to list the indoor and outdoor models, the pipe length included, the electrical work and any removal or gas disconnection. Request the plumbing class, ARC licence and electrical licence details with the quote. Check how long each price holds, the expected start date and how any VEU discount is shown. For ducted options, compare the outlets per room and the zone layout using the ducted installation guide.

Relocating an existing split system means recovering its refrigerant, so it needs the same licences as a new install. If you are moving house, book a Melbourne removalist for the furniture and leave any air conditioner to a licensed installer. Trees close to the outdoor position can drop leaves into the unit and block airflow over time. A Melbourne arborist can advise on pruning before the unit goes in, especially where council tree rules apply. Three written quotes on the same job description usually show what a fair price looks like.

Air Conditioning Installers Across Melbourne

Installers we work with cover metropolitan Melbourne, from CBD apartments and inner suburban terraces to houses in the newer outer suburbs. Ask about any travel charge when you book the site visit, so it appears on the written quote.

▶ Melbourne 32 areas
Melbourne CBD Carlton Fitzroy Richmond South Yarra Prahran St Kilda Brighton Bentleigh Caulfield Malvern Camberwell Hawthorn Box Hill Doncaster Ringwood Glen Waverley Clayton Dandenong Springvale Frankston Werribee Point Cook Footscray Sunshine Essendon Moonee Ponds Coburg Preston Reservoir Epping Craigieburn
▶ Geelong & Surf Coast 24 areas
Geelong Newtown Belmont Highton Waurn Ponds Grovedale Corio Lara Leopold Drysdale Clifton Springs Portarlington Queenscliff Point Lonsdale Ocean Grove Barwon Heads Torquay Jan Juc Anglesea Aireys Inlet Lorne Winchelsea Bannockburn Armstrong Creek
▶ Mornington Peninsula 26 areas
Mornington Mount Eliza Mount Martha Safety Beach Dromana McCrae Rosebud Rye Blairgowrie Sorrento Portsea Tootgarook Capel Sound Red Hill Main Ridge Arthurs Seat Balnarring Merricks Somers Flinders Shoreham Hastings Bittern Crib Point Somerville Tyabb
▶ Yarra Valley & Dandenongs 26 areas
Lilydale Mooroolbark Chirnside Park Coldstream Yarra Glen Healesville Badger Creek Launching Place Yarra Junction Warburton Wandin North Seville Silvan Monbulk Olinda Sassafras Kallista Belgrave Tecoma Upwey Ferntree Gully Upper Ferntree Gully Emerald Cockatoo Gembrook Macclesfield
▶ Ballarat, Bendigo & Goldfields 26 areas
Ballarat Wendouree Alfredton Delacombe Sebastopol Buninyong Creswick Clunes Daylesford Hepburn Springs Trentham Kyneton Castlemaine Maldon Harcourt Bendigo Kangaroo Flat Strathdale Eaglehawk Epsom Heathcote Maryborough Avoca Beaufort Talbot Dunolly

Melbourne Air Conditioning Installer FAQ

Does a split system installer in Melbourne need a plumbing licence?
Yes, in Victoria the refrigerant side of an air conditioning install is plumbing work regulated by the Building and Plumbing Commission. The installer needs a plumbing registration or licence in the refrigerated air conditioning class, or a restricted class for single head split systems. That restricted class covers single head splits up to 18 kW, ceiling cassettes and add-on outdoor units for ducted systems. Ask for the registration number and check it with the BPC before you pay a deposit.
Which refrigerant licence should the technician on my job hold?
The technician needs a licence from the Australian Refrigeration Council to handle refrigerant gas. The full RAC01 licence covers air conditioning work generally, and RSS03 covers single head split systems under 18 kW. The RDR04 domestic appliance licence does not cover split systems, so it is not enough. You can check both technicians and businesses through the Look for the Tick search.
How do I check that the wiring for my new air conditioner was certified?
The electrician must give you a Certificate of Electrical Safety, and for air conditioning work that should arrive within 30 days. You can search Energy Safe Victoria records to see whether an electronic certificate exists for your address. Air conditioning circuits are non-prescribed work, the everyday category, so no independent inspection is needed unless the switchboard is also changed. If no certificate arrives, contact Energy Safe Victoria.
Can I claim the Victorian Energy Upgrades discount after the system is installed?
Usually not, because the program says discounts typically cannot be applied after the work is done. The discount is applied through an accredited provider, or an installer working with one, before the work starts. The system must be an approved high efficiency reverse cycle product with at least a five year warranty for homes. Talk to an accredited provider before you buy anything if you want the discount.
What does the 1 March 2027 rental standard mean for a broken heater?
From 1 March 2027, a rental heater that fails and cannot be repaired must be replaced with fixed efficient electric heating. In practice that is a reverse cycle air conditioner with an outlet in the main living area. A separate cooling standard applies at the start of a new or periodic lease from the same date. From 1 July 2030, the cooling standard applies whether or not a new lease has started.
Until what time can my air conditioner run without breaching noise rules?
For cooling, it should not be heard in a neighbour's habitable room after 11 pm, or before 7 am on weekdays and 9 am on weekends and public holidays. When used for heating, the evening cut off is 10 pm instead of 11 pm. During a heat health warning, EPA Victoria says you can use your air conditioner for cooling at any time. Complaints about neighbourhood noise are handled by your local council.
Can an outdoor unit go on the front wall of a heritage house?
Port Phillip's heritage guidance says outdoor units must not be placed on or in front of the front facade, the main street-facing wall, of a dwelling. Under a heritage overlay, a permit is needed for household equipment that is visible from a street, other than a lane, or a public park. A unit that cannot be seen from a street or public park falls outside that trigger, although other zone rules can still apply. Check your planning property report and ask your council before you buy the unit.
Do I need owners corporation approval to put a split system on my balcony?
Usually yes, because owners corporation rules can require prior written approval for changes to the building's exterior or structure. An owner must not alter common property, the shared parts such as external walls, unless the owners corporation has authorised it. Ask for the building's rules and approval form before collecting quotes. Get the approval in writing before any deposit is paid.
Who disconnects the old gas heater when reverse cycle goes in?
Disconnecting a gas appliance is gasfitting work, so it needs a licensed gasfitter. Any work on a gas appliance or gas piping needs a compliance certificate, whatever the job costs. Some air conditioning businesses have a gasfitter on staff, while others expect you to book one separately. Check which arrangement applies before you compare the quotes you receive.
Who is responsible for a condensate leak after the install?
Turn the system off and contact the installer in writing, with photos of the leak and the date it started. Leaks often come from the condensate drain, which the BPC says must end at a safe point that avoids damage to the building. The work is covered by the consumer guarantees, so the business should fix it within a reasonable time. If it is not fixed, you can raise the problem with the BPC or seek advice from Consumer Affairs Victoria.

Melbourne Air Conditioning Specialists

For Trades & Contractors - VIC

Melbourne air conditioning jobs often need other licensed trades for the parts an installer cannot legally do. New circuits and switchboard work need an electrician, gas heaters need a licensed gasfitter to disconnect them, and ducted systems can need bulkheads or new ceiling insulation. These trades can be booked alongside an install anywhere across the metro area.

Compare Melbourne Air Conditioning Quotes

Tell us your suburb, the type of home and the rooms you want heated or cooled, and compare quotes from local Melbourne installers who are all pricing the same job.

Get Free Air Conditioning Quotes

About This Guide

This page provides guidance information only. Details may change, always verify with the relevant authorities and seek independent professional advice where needed.

Reviewed by The Quote Yard Editorial Team

Published 20 November 2026 ·

How The Quote Yard Works

We connect you with independent local tradies and service providers, we don't perform any trade work ourselves. Tradies provide their own quotes directly to you. Always confirm licensing, insurance, and scope of work before engaging any provider.

All Victorian tradies are required to hold appropriate licences. Verify at the Building and Plumbing Commission.
Prices are 2027 estimates based on typical metropolitan Melbourne air conditioning rates. Your final price will depend on the units chosen, the pipe length, access at height and any electrical work, so compare written quotes that list units, extras and electrical work separately.
Need work done? Get free quotes. Post a Job – It's Free