Looking for a Painter in Bunbury or the South West?

Tell us your town, the rooms or walls to be painted, any mould, water stains or flaking paint, and whether the property is a home, a holiday let or a business. We pass that description to painters across the region, so every quote is priced on the same details.

Get Free Painting Quotes

South West Painting Estimates

Painter, per hour$50 - $95
Room, walls only$300 - $750
Room, walls, ceiling and trim$400 - $900
Living area, walls, ceiling and trim$800 - $1,800
Whole interior, three bedrooms$3,000 - $8,000
Ceiling, flat white, two coats$8 - $16 per m²
Sealer or primer coat$8 - $14 per m²
Plasterboard repair before painting$250 - $900
Exterior repaint, single storey$4,000 - $12,000
Exterior repaint, double storey$8,000 - $20,000

These are estimated South West painting ranges for 2027. Your price depends on the preparation each surface needs, the products and coats chosen, access to the walls and the distance the painter travels.

Bunbury and South West Painting Contractors WA - Get Quotes

Painters across Bunbury and the South West work on family homes in Australind and Dalyellup, older houses in Bridgetown and Collie, and holiday houses near Dunsborough. Some repaints start with a damp problem, such as mould on a bathroom ceiling, a water stain from the roof or paint flaking off a wall that stays wet. WA Health advises scrubbing mould off hard surfaces with soapy water, drying the area and fixing the source of the moisture, and a good quote shows each of those steps. A stain blocking primer, a first coat that stops marks showing through, then goes under the mould resistant finish coats, with each maker's minimum wait between coats. Close to 200 places are on the City of Bunbury's Heritage List, where colour changes and paint types can need more thought and sometimes planning approval. Cafes, bakeries and winery kitchens must keep walls and ceilings in food areas sealed and easy to clean under the national Food Standards Code. Holiday lets add another step, because painting and drying time has to fit between guest bookings. Older houses may also have asbestos cement sheeting, which WorkSafe WA says must not be cleaned with high pressure water. Painters quote by the hour, by the square metre or as a fixed price, so the preparation lines matter as much as the total. Our 2027 estimates put one painter at $50 to $95 an hour and a single storey exterior repaint at $4,000 to $12,000. Post your job on The Quote Yard and we will connect you with local painters across Bunbury and the South West who can quote on it.

House, Shop and Holiday Let Painting in the South West

Painters work across the South West, from family homes in Greater Bunbury to cafes in Busselton and older houses in the forest towns. Every quote you receive through us is priced on the same written description of surfaces, damp problems and access.

Get Free Quotes

At a Glance - Bunbury and South West Painting Estimates for 2027

Job Estimated Band How It Is Charged What Adds Time Who Does It
Painter labour $50 - $95 an hour Per painter, per hour Unknown damage behind old paint Registered painter
Room, walls only $300 - $750 Per room Colour change and patching Painter
Room, walls, ceiling and trim $400 - $900 Per room Mould cleaning and stain blocking Painter
Living area, walls, ceiling and trim $800 - $1,800 Per area Ceiling height and windows Painter
Whole interior, three bedrooms $3,000 - $8,000 Fixed price Wet rooms and furniture Painting contractor
Feature wall $200 - $500 Per wall Strong colour needing extra coats Painter
Ceiling, flat white, two coats $8 - $16 per m² Per square metre Water stains needing a primer Painter
Interior door and frame $130 - $260 each Per door Old gloss enamel needing a primer that grips Painter
Plasterboard repair before painting $250 - $900 Per sheet area Extent of water damage Plasterer or painter
Render or texture coat $35 - $75 per m² Per square metre Cracks and drummy, hollow-sounding patches Painter or renderer
Weatherboard repaint $40 - $85 per m² Per square metre Loose paint and timber repairs Painter
Exterior, single storey $4,000 - $12,000 Fixed price Surface type and travel Painting contractor

Where Extra Cost Comes From on a South West Repaint

What is involved
Mould, water marks and soft plaster need cleaning, drying, repairs and a blocking coat before the finish coats.
Furnished holiday houses and occupied homes add time for moving and covering furniture.
Heritage places can need paint scrapes, breathable paints and a check with the council first.
Jobs far from the painter's base can carry a travel charge on each day of work.
Send every painter the same room list, photos of any mould or stains and the products you prefer, then compare the totals line by line.

Painting a Home or Business Between Australind and Augusta

South West painting jobs range from newer homes in Eaton and Dalyellup to older houses in the forest towns and holiday houses near Dunsborough. Some owners call a painter because of damp, which can show as black spots on a bathroom ceiling, a brown ring from a roof leak or paint lifting off a wet wall. Each of those faults needs a different first step, such as cleaning or a repair, and that work is done before anyone chooses a colour. The paint system, meaning the primer and finish coats used together, also differs by surface, and our guide to painting services in WA compares them for render, brick, timber and metal across the state. Every price below is a 2027 estimate, and only a written quote from a painter who has seen the job fixes what you pay.

One owner may need a single bedroom freshened before a sale, while another is repainting a cafe in Busselton or a cottage in Bridgetown after a leaking roof. WA Health calls excess moisture the key ingredient for mould growth, so a mouldy ceiling can point to a leak, a missing exhaust fan or a roof fault. The trades that deal with those faults, such as a plumber, an electrician who fits exhaust fans or a roofer, may need to come before the painter. Planning the order of trades, and giving every painter the same written brief, makes the quotes much easier to compare.

South West Room, Wall and Exterior Bands for 2027

Labour for one painter working alone costs an estimated $50 to $95 an hour in 2027, although jobs that run over several days can be quoted as a fixed price instead. Repainting the walls of a single room comes to about $300 to $750, while walls, ceiling and trim together sit at roughly $400 to $900. Living areas with walls, ceiling and trim are estimated at $800 to $1,800, depending on their size, the ceiling height and the number of doors and windows. For a whole three bedroom interior our estimates run from $3,000 to $8,000, and a four bedroom interior from $5,000 to $15,000. These bands come from the statewide figures on our WA painting pages, widened where those pages differ, so they are not specific to any one South West town. Our interior painting guide for WA compares finishes room by room, including sheen levels, meaning how glossy the dried paint looks.

Exterior repaints are estimated at $4,000 to $12,000 for a single storey home and $8,000 to $20,000 for a double storey home. Render and texture coatings, the cement-based or textured finishes laid over masonry walls, are priced at about $35 to $75 per square metre, and weatherboard repaints at $40 to $85 per square metre. Fibre cement sheeting runs at $45 to $75 per square metre, while painted face brick sits lower at $30 to $55. Eaves and fascias, the boards along the roof edge, cost an estimated $25 to $50 per linear metre, and a full exterior door with sanding, priming and gloss enamel costs $300 to $900. Where a stained or mouldy surface first needs a sealer or primer, a base coat that seals the surface and helps paint grip, that extra coat adds roughly $8 to $14 per square metre.

Damp repairs can add items that sit outside the painter's own rates. Plasterboard that has softened or been cut out after a leak costs an estimated $250 to $900 per sheet area to repair. A plasterer can quote on that repair through our plastering and gyprock repairs service before the painter starts. Flat white ceilings, where bathroom mould is easy to see, are estimated at $8 to $16 per square metre for two coats. Moving furniture and protecting floors adds about $300 to $800 when the painter handles it, which is a real cost in a fully furnished holiday house.

Job 2027 Estimate Charged By Notes for South West Jobs
Painter labour $50 - $95 an hour Per painter, per hour Suits small repairs and touch-ups
Room, walls only $300 - $750 Per room Room size and colour change
Room, walls, ceiling and trim $400 - $900 Per room Mould cleaning priced on top
Living area, walls, ceiling and trim $800 - $1,800 Per area Ceiling height and windows
Whole interior, three bedrooms $3,000 - $8,000 Fixed price Wet rooms needing extra preparation
Whole interior, four bedrooms $5,000 - $15,000 Fixed price Furniture and occupied rooms
Ceiling, flat white, two coats $8 - $16 per m² Per square metre Stain blocking coat if marked
Sealer or primer coat $8 - $14 per m² Per square metre Water marks and new plaster
Plasterboard repair before painting $250 - $900 Per sheet area Extent of water damage
Exterior, single storey $4,000 - $12,000 Fixed price Surface type and travel
Exterior, double storey $8,000 - $20,000 Fixed price Access equipment needed
Strata or commercial repaint $8,000 - $25,000+ Fixed price or tender Trading hours and food areas

How a South West Painter Builds a Price From Preparation Upward

Painters price work in three main ways, and a single quote can mix all of them. Small repairs, touch-ups and jobs where the hidden damage is unknown can be charged by the hour, so the final bill depends on the time actually spent. Wall, ceiling and cladding areas can be measured and priced per square metre, with trims and eaves priced per linear metre and doors priced one by one. Larger jobs can be turned into one fixed price after a site visit, which gives certainty as long as the scope is clearly written down. Whichever method is used, the quote should show how many coats are included and which products the painter plans to use.

Preparing a damp or mouldy surface should appear as its own line on the quote, because it can take longer than the painting itself. That line might cover washing walls with sugar soap, a mild cleaner for painted surfaces, treating mould, scraping loose paint, filling cracks and applying a stain blocker or sealer. When those steps are folded into a single room rate, two painters can quote very different totals for what looks like the same work. Travel is another separate cost on regional work, for example when a painter based in Bunbury drives to Augusta, Northcliffe or Boyup Brook each day. We do not publish a travel band for the region, so compare how each painter charges for it, whether as a flat fee, a rate per kilometre or paid travel time. Painters working far from home deal with the same question in farming districts, and our Avon Valley and Wheatbelt painter guide has more detail on travel fees and minimum charges.

Lines a South West Painting Quote Should Separate

What each line shows
Preparation, including mould cleaning, scraping, filling and sanding, listed apart from the painting labour.
Each product named by maker and product line, with the number of coats for every surface.
Any primer, sealer or stain blocking coat shown as its own item, so you can see whether it is included.
Travel, accommodation or a daily drive charge where the job sits well away from the painter's base.
Repairs to plaster, render or timber that another trade will carry out, with the cost shown separately.
A fixed price that names every item gives you the safest basis for comparing quotes, because missing preparation becomes easy to spot.

Tracing the Moisture Behind Mouldy or Peeling Paint

WA Health describes excess moisture as the key ingredient for mould growth, and that moisture can come from outdoors or from activities inside the home. Its list of sources includes leaking surface water, rising damp, meaning ground moisture drawn up into walls, rain entering through the roof or walls, and plumbing leaks inside the house. Showering, cooking and boiling water without an exhaust fan or open window add moisture too, as do clothes dryers and unflued gas heaters, which have no outside vent, in poorly ventilated rooms. The same advice says mould commonly grows in bathrooms, kitchens, cluttered storage areas, wall and roof spaces, and behind furniture. Signs of damp you cannot see include a musty or earthy smell, regular condensation and a home that often feels humid.

Painters can clean and coat a mouldy wall, but the mould is likely to return if the water keeps coming. Before booking the painting, find out whether the damp comes from a leak, from the roof, from the ground or from steam produced inside. For plumbing leaks WA Health suggests a plumber, and a builder or roof specialist for leaks through the structure of the house. For a leaking pipe in a wall cavity or a dripping shower, you can compare local tradespeople through our guide to hiring a plumber in Bunbury and the South West. Roof leaks that stain a ceiling need fixing before the ceiling is painted, and our roof repairs and roof painting services handle the roof itself. Once the source is fixed, give the wall or ceiling time to dry out properly before any primer goes on.

What You Can See Possible Moisture Source Trade to Call First Painting Step Afterwards
Black spots on a bathroom ceiling Steam from showers without an exhaust fan Electrician to fit or repair a fan Clean, dry, block stains, then ceiling paint
Brown ring or stain on a ceiling Rain entering through the roof Roofer Stain blocking primer, then two coats
Bubbling paint low on a masonry wall Rising damp or water from the ground Builder or damp specialist Repaint only once the wall has dried
Mould behind wardrobes and beds Poor airflow and condensation No trade, better ventilation first Clean, dry and repaint
Peeling paint near a shower or basin Plumbing leak or failed seals Plumber or waterproofer Repair plaster, seal and repaint
Musty smell but no visible mould Hidden mould in a wall or roof space Builder or mould specialist Paint only after the source is found

Bathrooms, Laundries and Kitchens That Run Wet

Rooms where water is heated or sprayed every day produce moisture that needs a way out of the house. Consumer Protection advises WA landlords to provide exhaust fans in all areas where moisture is produced, such as bathrooms, kitchens and laundries. An electrician can fit a new exhaust fan or replace one that has stopped working, and you can compare local electricians through our Bunbury and South West electrician guide. Painting a bathroom ceiling without fixing the airflow leaves the new coat exposed to the same steam every morning.

Dulux makes Wash&Wear +PLUS Kitchen & Bathroom, which it says was developed to withstand humid or damp environments. The company advertises a 10-year guarantee against mould growth for that range, and refers buyers to the product label for the full conditions. Wattyl makes I.D Advanced Anti-Mould Ceiling, a flat ceiling paint that it says will resist mould growth for five years from the date of application. Wattyl's warranty depends on the paint going onto a properly prepared surface, so the cleaning and priming steps still matter. Mould resistant topcoats, the finish coats you see, resist growth on a clean, dry surface, but they will not dry out a wall that is still wet. Shower recesses that leak into the wall behind need sealing first, and our bathroom waterproofing service handles that repair before any repaint.

Moisture Checks Before a Wet Room Is Repainted

What to check
Run the exhaust fan and hold a sheet of tissue near the grille to see whether it draws air.
Open the window fully and check that it can be left open securely while the room dries.
Look for leaks around the shower, bath and basin, including marks on the other side of the wall.
Check the ceiling for brown rings, which can mean roof water rather than steam from the shower.
Fix leaks and airflow first, then book the painter, so the new coat does not go over a wall that is still drawing in moisture.

Removing Mould From a Surface Before the First Coat

The cleaning steps published by WA Health begin with scrubbing hard surfaces with soapy water, because all the mould must be physically removed to prevent regrowth. Scrubbing should extend up to 50 centimetres past the edge of the visible mould. Residue is then wiped up with a damp cloth or collected with a vacuum cleaner fitted with a HEPA filter, a fine filter that traps very small particles. After that the area is dried, and the source of the moisture is found and fixed. WA Health says soapy water is usually enough, although commercial products or natural antifungals such as vinegar or tea-tree oil can also be used. Fungicides developed for outdoor use should not be used on indoor mould, so check the label before a product goes on a bedroom or bathroom wall.

Rubber gloves, a face mask and safety goggles are the protective gear WA Health lists for cleaning mould. 3M makes the Construction Respirator Kit 6535, a reusable half face mask fitted with P2 filters for fine particles, which the company lists for mould or lead clean-up work. Ventilate the room while you work, but avoid strong air movement, such as a fan blowing across the wall, that could spread spores into other rooms. Selleys makes Rapid Mould Killer, and like any mould product it should only go on the surfaces its label lists.

Professional help may be needed if the mould covers a large area, keeps coming back or cannot be found, according to WA Health. The same advice says mould sampling is not necessary to judge the health risk, so a laboratory test is not a step every job needs. Stubborn cases can be handed to a specialist through our bathroom mould removal and prevention service before the painter returns. Before hiring anyone to remove mould, WA Health suggests checking their experience and track record.

Step What WA Health Describes Who Does It Painting Note
Protect yourself Rubber gloves, a face mask and safety goggles Painter, cleaner or owner Cover floors and furniture first
Scrub Soapy water, up to 50 cm past the visible mould Painter or cleaner Paint will not hide mould left behind
Collect residue Damp cloth or a HEPA filter vacuum Painter or cleaner Removes loose spores before sanding
Dry the area Ventilate without strong air movement Owner and painter Primer goes on a dry surface only
Fix the source Find and repair the moisture problem Plumber, electrician, roofer or builder Book the painter after the repair
Get help if needed Large, recurring or hidden mould Mould specialist Painter quotes on the finish coats

Blocking Coats for Water Marks and Old Mould Shadows

Cleaning removes the mould itself, but a water mark or grey shadow can still show through ordinary paint. A stain blocking primer is a first coat that seals the mark so it does not bleed into the finish coats. Dulux makes PRECISION Stain & Mould Blocker, a water-based stain blocker that it says is formulated to inhibit mould and mildew growth. The product is listed for interior surfaces and spot exterior use, and Dulux suggests testing for bleed-through by applying the topcoat to a small section after priming. Its stated touch dry time, when the surface can be lightly touched, is 20 minutes, and its recoat time, the wait before the next coat, is two hours.

Taubmans makes Advanced Adhesion And Mould Blocker, a water-based prepcoat, meaning a coat applied before the finish coats, for blocking persistent oil, grease and mould-based stains. Taubmans says it is for inhibiting future mould growth, lists it for interior and exterior use and describes it as suited to high humidity areas. Zinsser makes Bulls Eye 1-2-3, a water-based primer and sealer for interior and exterior use, and recommends its Bulls Eye 1-2-3 PLUS for water stains. Each product suits different stains and surfaces, so the quote should name the primer the painter will use on each area. If a painter plans to skip the blocking coat on a stained ceiling, ask for the reason in writing before the job starts.

Primers only work properly on a surface that is clean, dry and sound. Dulux tells users of its stain blocker to remove as much of the stain as possible first by cleaning with sugar soap, sanding or scraping. Loose or flaking paint is scraped back, holes and cracks are filled and sanded smooth, and new render or concrete must be properly cured, meaning fully hardened, before priming. Uni-Pro makes scrapers, broad knives and patchers, the hand tools used for that scraping and filling work. Where the plaster behind a stain has gone soft, it needs repairing before any primer is applied. Sanding marked paint creates fine dust, and Festool makes random orbital sanders while Mirka makes the DEOS and DEROS sanders, so check whether the painter's sander runs with dust extraction.

Choosing a First Coat for a Marked Surface

Situation
First coat to discuss
Grey shadow left after mould cleaning
Water-based stain and mould blocker
Brown water ring from a roof leak
Stain blocking primer tested with a topcoat patch
Tannin, a natural timber stain, bleeding through trim
Primer, sealer and undercoat that blocks tannin
Old glossy enamel on doors
Primer that adheres to aged enamel
Fresh plaster patch after a leak
Sealer coat before the finish coats
Ask the painter to name the first coat for every marked area, because a quote without a blocking coat can look cheaper while leaving stains to show through.

Anti-Mould Ceiling Paint: What the Five-Year Cover Includes

Wattyl's five-year warranty on I.D Advanced Anti-Mould Ceiling covers free product to recoat the affected area, or a refund of the purchase price, at Wattyl's choice. Labour and equipment costs are not covered, so a failed ceiling still means paying a painter to do the work again. The warranty applies only where the paint went on sound, properly prepared surfaces in line with Wattyl's technical data sheets, the maker's printed instructions for each product. Claims need proof of purchase and proof of the maintenance the data sheet requires, and Wattyl may inspect the property at its own cost. It also excludes commercial or business projects, because the warranty is written for residential customers only.

That last point matters to owners of cafes, shops and other business premises, who should check whether a warranty applies to their building before choosing a product for that reason. Keep the receipt or the painter's invoice naming the product and colour, because any claim depends on that paperwork. Workmanship is a separate matter from the paint maker's warranty. Under the Australian Consumer Law a business must provide services with acceptable care and skill, and the Australian Competition and Consumer Commission (ACCC) publishes guidance on consumer guarantees and remedies. The painter's own written workmanship warranty adds a set period and a process for fixing defects, so request its length and terms with the quote. Store the product names, colours and invoices in one folder for the property, ready for the next repaint or a warranty claim.

What a Mould Resistant Paint Warranty Can Exclude

Check these points
Labour and equipment, so the cost of a painter returning is not part of the product warranty.
Failures caused by incorrect use of the product or by causes outside the maker's control.
Commercial or business projects, where the warranty is written for residential customers only.
Later owners of the property, unless the product was bought on the owner's behalf.
Read the maker's warranty terms before relying on them, and keep proof of purchase and maintenance with your property records.

Mould in a Let House: Who Pays Before the Painter Starts

The Consumer Protection bulletin for landlords on mould says a tenant is only responsible for mould they have caused. Examples it gives include not using working exhaust fans, not ventilating the home and leaving surfaces wet. A landlord cannot ask the tenant to pay for treating or removing mould caused by a structural issue with the property. The bulletin also says owners should make sure there is no mould in a property before it is rented out. If mould covers a large area or keeps coming back, it recommends treatment by a mould removal professional. Owners of let houses in Bunbury, Busselton or Collie should keep the painter's invoice and photos with the property's maintenance records.

Owners with a let house near the coast can read about repaints between tenancies, and tenant requests to paint, in our guide to Mandurah and Peel painters. For mould, the practical step is to agree in writing who arranges the clean, the repair and the repaint before a painter is booked. Tenants with questions can contact Tenancy WA or Consumer Protection, both listed by WA Health as sources of advice. If the mould keeps returning after cleaning, the moisture source is the problem to raise with the owner or property manager, not the paint.

Cause of the Mould Who Pays Under the Bulletin Painting Step Record to Keep
Roof leak or other structural fault Landlord Repair, clean, block stains and repaint Repair invoice and photos
No exhaust fan in a wet area Landlord should provide fans Repaint after the fan is fitted Electrician invoice
Tenant not using a working fan Tenant, for mould they caused Clean and repaint if marks remain Inspection report and photos
Surfaces regularly left wet by the tenant Tenant, for mould they caused Clean first, repaint only if needed Entry and exit condition reports
Large or recurring mould Treatment by a mould professional Paint only after treatment Specialist report

How Long Each Coat Needs Before the Next One Goes On

Every paint maker prints its own touch dry and recoat times on the data sheet for each product. Three coats on one wall take longer than the rolling time alone, because each coat has to wait out its recoat time. Haymes lists its NEW LOOK Exterior Low Sheen as touch dry in 30 minutes, with a recoat time of two hours. The same data sheet says not to apply it below 10°C or above 35°C, or if rain or dew is expected within 24 hours. Haymes adds that drying times are extended at cooler temperatures or higher humidity, so the printed times can stretch on some days. Exterior paint systems for render, weatherboard and fibre cement are compared in our exterior painting guide.

Exterior timber paints have their own drying figures, which matter on weatherboards, fascias and window frames. Cabot's makes Timbercolour Deck & Exterior Paint, an exterior timber paint with a touch dry time of 30 minutes and a recoat time of at least two hours. Cabot's says the temperature must stay above 10°C during application and drying, and recommends two generous coats, or three on unpainted timber. For new timber it suggests Cabot's New Timber Prep to draw out tannins and oils, followed by a wash and at least an hour of drying before coating. Rotten or split boards should be replaced before any coating, and our cladding repairs service can arrange that work. Decks have their own coatings and cure times, and our guide to Mandurah and Peel painters looks at them in more depth.

Recoat time is not the same as the time before a room can be used normally, so check with the painter when furniture, rugs and pictures can go back. For a holiday let or a cafe, that answer decides how many days the property stays closed. Write the agreed drying period into the quote along with the products, so the booking calendar or trading roster can be planned around it. Where a painter suggests a faster drying primer to fit a short gap, confirm that it suits both the surface and the topcoat.

Product and Maker Touch Dry Recoat Conditions the Maker States
NEW LOOK Exterior Low Sheen, Haymes 30 minutes 2 hours 10°C to 35°C, no rain or dew expected within 24 hours
Timbercolour Deck & Exterior Paint, Cabot's 30 minutes 2 hours minimum Above 10°C during application and drying
PRECISION Stain & Mould Blocker, Dulux 20 minutes 2 hours Interior and spot exterior use

Colour Evidence and Paint Types for Bunbury Listed Places

Close to 200 places appear on the City of Bunbury Heritage List, and the City has one heritage area, in East Bunbury. The City says heritage listings do not prohibit development, but in most circumstances development at these places requires planning approval. Its Local Heritage Survey is different, because it only records information and has no legal effect on what you can do with the land. WA planning regulations exempt maintenance and repair works from approval, but at heritage-protected places the exemption only covers works of the kinds listed in the Heritage Regulations 2019. Talk to the City's planning team early, before a painter changes the colours of a listed house or shopfront. Masonry repairs on the same buildings bring their own questions, which our guide to hiring a bricklayer in Bunbury and the South West describes.

For places on the State Register of Heritage Places, the Heritage Council of WA has a Policy and Practice Note for Painting Heritage Places, published on wa.gov.au. It favours colour schemes based on evidence of original or early colours, and says paint scrapes should be done to inform decisions about repainting. A paint scrape is a small test area, taken in an inconspicuous spot, that reveals the layers of earlier colours underneath. The policy says scrapes are preferably done by professionals experienced in the technique, with the results recorded, and it names historical photographs as another source of colour evidence. Its principles can also guide decisions about places on local heritage lists, such as Bunbury's.

The same policy says all previously unpainted surfaces should remain unpainted, noting that face brick and stonework were often chosen for their contribution to the overall design of a place. Breathability, meaning how easily moisture vapour passes through a coating, is treated as the most important factor in choosing a paint. For lime and early cement render, its choices are traditional limewash, a coating of lime mixed with water, then clay-based paint or a mineral paint with similar breathability. Metalwork suits gloss enamel or a modern acrylic equivalent, and the policy warns that water-based paints can cause iron to rust. Care is also called for when stripping oil-based paints from buildings constructed before 1970 because of possible lead, and our Perth painter guide explains the WA lead paint advice. Solver makes Trims High Gloss Enamel, an oil-based enamel topcoat for interior and exterior use, which matches the oil-based gloss enamel the policy lists for exterior timber doors and windows.

Surface Heritage Council Policy Approach Question for the Painter Who Else to Contact
Face brick or stone never painted Leave it unpainted Has painting it been suggested, and why City planning team
Lime or early cement render Limewash, clay paint or breathable mineral paint Which breathable product will you use Heritage adviser if listed
Timber joinery Oil-based enamel or primer, or compatible acrylic Which primer goes under the topcoat None for like-for-like work
Iron and other metalwork Gloss enamel or a modern acrylic equivalent How will rust be treated first Heritage adviser if listed
Old oil-based layers before 1970 Strip with care because of possible lead How will paint be tested and dust controlled Lead testing service

Holiday Houses Near Dunsborough and Margaret River: Painting While Nobody Is Staying

If you own a holiday house around Dunsborough, Yallingup or Margaret River but live in Perth or further away, the painter may be working with nobody on site. The cleaner who already looks after the house can be a useful contact, and our South West cleaner guide deals with keys, lockboxes and changeover cleans. Book the final clean after the paint has passed its drying time, so dust and cleaning products do not land on fresh paint. Furnished houses also need beds, sofas and artwork moved and covered, so confirm whether that work is included in the price.

Choose a gap between bookings that covers the painter's days on site as well as the drying figures for the chosen products. If the property is let through a manager, agree who lets the painter in, who checks the work and who signs off before guests return. Photos taken before and after each room help settle any later question about marks on furniture, floors or fittings. Ask the painter to cover anything that stays in place, such as fixed beds, built-in furniture and timber floors. If the house has developed mould while closed up between visits, deal with it using the cleaning steps above before the painter quotes on the finish coats.

Briefing a Painter for a House You Are Not Visiting

What to send
A floor plan or photo of each room, with the walls, ceilings and trims to be painted marked clearly.
The booking calendar for the next few months, showing the longest gap available for the work.
Who holds the keys, the alarm details and the name of the person who will check the finished job.
Colour names, makers and sheen levels for any surfaces that must match the existing paint.
A list of furniture and fittings that must not be moved, with photos showing where each item sits.
Agree in writing that the painter will send photos of each finished room before the final invoice, so you can check the work from a distance.

Cafes, Bakeries and Winery Kitchens: Surface Rules in Food Areas

Commercial painting in the region ranges from shopfronts in central Bunbury to kitchens and tasting rooms around Margaret River. Where food is handled, the national Food Standards Code applies, and Standard 3.2.3 sets rules for the walls and ceilings of food premises. Walls and ceilings provided to protect food must be sealed to keep out dirt, dust and pests, and must be unable to absorb grease, food particles or water. They must also be able to be easily and effectively cleaned and, as far as practicable, unable to provide harbourage for pests, meaning places where pests can hide or breed. A commercial kitchen therefore needs a paint system that stands up to regular cleaning, and flaking paint above a food preparation area needs fixing promptly.

Councils in WA have environmental health officers who deal with food premises, so check with your local council if you are unsure what finish suits a food area. Painting a working cafe also means planning around trading hours, deliveries and the smell of fresh paint near food. Some owners stage the work over closed days or nights, with food stored away and benches covered before the painter starts. The quote should name the product for each area, because kitchen walls, dining rooms and toilets may each need a different finish. For larger premises, line marking or a multi-storey building, you can compare specialists through our commercial painting service for WA. Repaints of strata buildings, where owners share the common areas, and of commercial premises are estimated at $8,000 to $25,000 or more in 2027, depending on the building and the access needed.

Area What Standard 3.2.3 Requires Painting Point Timing
Kitchen walls Sealed, non-absorbent and easily cleaned Washable finish over a sound, sealed base Closed days or overnight
Kitchen ceiling Sealed against dirt, dust and pests Fill gaps and cracks before painting Before the walls
Dry storeroom No pest harbourage, as far as practicable Seal gaps at joints and pipe openings When stock can be moved
Food preparation area in a bar or tasting room Sealed and easily cleaned where walls protect food Choose a finish that suits regular wiping Outside service hours

Keeping the Price Fair When Local Painters Are Booked Out

A fair price is easier to judge when every painter quotes the same scope, with the same products and a similar start window. Send each painter the same written brief, photos of each wall or room, and a note of any mould, stains or soft plaster. Request a fixed price that stays valid for a stated number of days, and a start date written into the quote. If one quote is much higher, compare the preparation lines, coats and products before deciding it is overpriced. If one quote is much lower, check whether it leaves out mould treatment, a blocking primer or the extra coat that a strong colour change can need.

WA rules on painter registration, written contracts and deposits apply in the South West as well, and our guide to house painters in Perth goes through them. Under the Building Services (Registration) Act 2011 and its regulations, paid painting work valued at $1,000 or more must be contracted by a registered painting contractor. Choosing a painter who cannot start for some weeks can still make sense, as long as the price is held in writing until the start date. Be wary of any request to pay the full amount before work begins, and pay progress amounts only for work you can see has been done. Keep every quote and message in writing, along with any variation, meaning a change to the job such as new products or colours agreed on site. If a dispute cannot be settled with the painter, a complaint about a registered painter's work can be lodged with the Building Commissioner at Building and Energy.

Render, Washing and Asbestos Checks Around a Damp Repair

Damp repairs can involve several trades, and the painter's work comes after the others have finished. Cracked render can be repaired and recoated through our render and texture coating service before the painter returns. Pressure washing before an exterior repaint can be booked separately through our pressure cleaning service, but some materials must never be water blasted. WorkSafe WA states that high pressure water must not be used on asbestos cement material, and that preparation for painting it can only use non-abrasive methods that do not scratch the surface. WorkSafe WA also says replacement is recommended over painting where asbestos cement is in poor condition.

If you are unsure whether a sheet in the eaves, a wet area or an old extension contains asbestos, arrange asbestos testing and inspection before preparation starts. Removal, where it is needed, is a separate job that you can arrange through our asbestos removal service. Older farmhouses and asbestos cement sheds raise the same questions, and our guide to Avon Valley and Wheatbelt painters goes into them further. Keep any test results with the brief, so every painter prices the same preparation method.

Trades That May Need to Finish Before the Painter

Problem
Trade to book first
Leaking pipe, tap or shower
Plumber or waterproofer
Missing or broken exhaust fan
Electrician
Roof leak staining a ceiling
Roofer
Soft or cut-out plasterboard
Plasterer
Cracked or drummy render
Renderer
Sheeting that may contain asbestos
Asbestos testing service
Book the trades in order and give the painter the finish date of the last one, so the quote can include drying time before the first coat.

What to Look Out For When South West Painting Quotes Arrive

Look first at whether the quote mentions the damp at all, because a price for painting a mouldy ceiling should include cleaning, drying and a blocking coat. Vague wording such as 'prepare surfaces as needed' leaves room for argument later about what was included. Check that each product is named by maker and product line, so you can look up its data sheet and any warranty. Count the coats listed for each surface, and confirm whether the primer is counted as one of them. On heritage places, look for a note about paint scrapes, original colours and any approval the City needs. For holiday lets and food businesses, the quote should state the days the property must stay closed and when it can reopen.

Be cautious of a quote that promises the mould will not return without mentioning the source of the moisture. No paint system can make up for a leak, and the maker warranties described above rely on properly prepared surfaces. Check that the business name on the quote matches the registration and insurance details the painter provides. Low prices may also leave out travel, furniture moving or repairs to soft plaster, so read the exclusions before you compare totals.

Warning Signs to Check Before You Sign

Look for
No line for mould cleaning or stain blocking on a job where you reported mould or water marks.
Paint described only as premium or quality, with no maker, product line or sheen level.
A promise that a new coat will fix damp, with no question about leaks, fans or the roof.
Full payment requested before work starts, or a deposit with no written contract.
No drying period stated for a holiday let, rental changeover or food business.
Put any question about the quote to the painter in writing, and keep the answer with the quote you accept.

Sending One Brief to Several South West Painters

Write one brief and send the same version to every painter you contact. List each room or wall, the surfaces involved, the current colour and the new colour, and mark any mould, water stains or flaking paint on a simple floor plan. Include photos taken in daylight, the age of the house if you know it, and any heritage listing. Say whether the house is lived in, let to tenants, used as a holiday let or run as a business, because that changes how the work is timed. Mention the town as well, since a painter based in Bunbury may price a job in Pemberton differently from one in Eaton because of travel. Brush washing and leftover paint need a plan too, and our Swan Valley and Perth Hills painter guide covers disposal on blocks with tanks and septic systems, plus ladder safety on steep ground.

When the quotes come back, set them side by side and compare preparation, products, coats, travel, exclusions and the start date. Ask any painter who left something out to add it, so every quote prices the same work. Request the workmanship warranty terms and the name of each product, so you can check the maker's own conditions too. If the garden, paths or walls also need work, our guides to South West landscapers and South West concreters can help you plan the order of trades. For whole-house repaints inside and out, our house painting guide for WA compares interior and exterior work across the state. Allow enough time between accepting a quote and the start date to fix any leaks or airflow problems first.

Painters Across Bunbury and the South West

Painting prices on this page apply across Bunbury and the South West, from Australind and Busselton to Bridgetown. Travel is a real cost on regional work, so a job a long drive from the painter's base may carry a travel charge on the quote.

▶ Greater Bunbury 7 areas
Bunbury Leschenault Australind Eaton Dalyellup Gelorup Capel
▶ Busselton & Geographe Bay 6 areas
Busselton Abbey Broadwater Vasse Dunsborough Yallingup
▶ Margaret River Region 5 areas
Cowaramup Gracetown Margaret River Witchcliffe Augusta
▶ Harvey & Collie 4 areas
Harvey Yarloop Brunswick Junction Collie
▶ Blackwood & Southern Forests 8 areas
Donnybrook Balingup Nannup Bridgetown Boyup Brook Manjimup Pemberton Northcliffe

South West Painting Questions

Can a mould resistant ceiling paint fix a bathroom without an exhaust fan?
Mould resistant paint is made to resist growth on a clean, dry surface, but it does not remove the moisture that feeds mould. Showering without an exhaust fan or open window is one source of indoor moisture listed by WA Health. Consumer Protection advises WA landlords to provide exhaust fans wherever moisture is produced, including bathrooms. Fit or repair the fan first, then clean, prime and repaint the ceiling. Without that step, the new paint faces the same steam every day.
Should mould be tested in a laboratory before a painter quotes on the cleanup?
WA Health says mould sampling is not necessary to determine the health risk. Its advice is to treat any mould or dampness as a potential health risk and deal with it promptly. Professional help may be needed if the problem is large, keeps coming back or cannot be found. In those cases a mould specialist can assess the source before the painter quotes on the finish coats.
What protective gear should be worn when scrubbing mould off a wall?
For cleaning mould, WA Health lists rubber gloves, a face mask and safety goggles. 3M makes a reusable half face respirator kit with P2 particle filters that it lists for mould or lead remediation. Ventilate the room while you work, but avoid strong air movement that could spread spores to other areas. Cover nearby furniture and floors before scrubbing starts. Wash the gear and your hands once the job is finished.
How long should I wait between a stain blocking primer and the first topcoat?
Follow the recoat time printed by the maker of the primer you are using. Dulux lists a 20 minute touch dry time and a two hour recoat for PRECISION Stain & Mould Blocker. The topcoat has its own figures too, such as two hours for Haymes NEW LOOK Exterior Low Sheen. Drying can take longer in cool or humid conditions, so check the data sheet before the next coat.
Who pays to fix mould in a rental house in Bunbury?
Consumer Protection's landlord bulletin says a tenant is only responsible for mould they have caused. Examples include not using working exhaust fans, not ventilating the home and leaving surfaces wet. Landlords cannot ask the tenant to pay for treating mould caused by a structural issue. If mould covers a large area or keeps returning, the bulletin recommends a mould removal professional. Agree in writing who arranges the clean and the repaint before the painter is booked.
What is a paint scrape and why would a heritage adviser want one?
It is a small test area, taken in an out-of-sight spot, that shows the layers of earlier colours on a surface. The Heritage Council of WA's painting policy says scrapes should be done to inform decisions about repainting places on the State Register. It also says they are preferably done by professionals experienced in the technique, with the results recorded. The findings can support a colour scheme based on original or early colours. Historical photographs can add further evidence of how the building once looked.
Which paints suit old lime render on a listed building?
The Heritage Council of WA's painting policy names traditional limewash and clay-based paint for lime and early cement render. A mineral-based paint can be considered if it has similar breathability and porosity. Breathability, meaning how easily moisture vapour passes through a coating, is the factor the policy treats as most important. The policy applies to places on the State Register, and its principles can guide decisions on local heritage lists. For a place on the City of Bunbury's Heritage List, speak to the City's planning team before any work.
What finish do walls in a cafe kitchen need under the Food Standards Code?
Standard 3.2.3 says walls and ceilings provided to protect food must be sealed to keep out dirt, dust and pests. They must be unable to absorb grease, food particles or water, and able to be easily and effectively cleaned. As far as practicable, they must also be unable to provide harbourage for pests, meaning places where pests can hide or breed. The painter should name a washable product for each area and confirm the base coats it needs. Your council's environmental health officers can advise if you are unsure.
Does an anti-mould paint warranty apply to a cafe or other business?
The Wattyl warranty for I.D Advanced Anti-Mould Ceiling excludes commercial or business projects, because it is written for residential customers only. It also leaves out labour and equipment costs, offering free product or a refund of the purchase price instead. Other makers set their own terms, so read the warranty for the exact product before choosing it for a business. In a cafe kitchen, the Food Standards Code rules on sealed and cleanable walls apply whatever paint is used. The painter's own workmanship warranty is a separate promise, so request its terms in writing.
How do I hold a painter to a price if they cannot start for several weeks?
Request a written fixed price that states how long it stays valid and the agreed start date. Check that the quote names each product, the coats and the preparation, so the scope cannot shrink later. Avoid paying the full amount before work begins, and pay progress amounts only for work you can see. Keep every message, variation and receipt in writing with the quote. If a dispute cannot be settled with the business, a complaint about a registered painter's work can go to the Building Commissioner.

Painting and Surface Specialists in WA

For Trades & Contractors - WA

Preparing walls for paint can uncover work for other trades, such as a leaking pipe, a broken exhaust fan, damaged render or sheeting that needs an asbestos test. Trades that take on that kind of work in Western Australia are listed below, along with job leads for painters looking for new clients.

Compare South West Painting Quotes

Tell us your town, the rooms or walls to be painted and any damp or access issues, and local painters can send written quotes.

Get Free Painting Quotes

About This Guide

This page provides guidance information only. Details may change, always verify with the relevant authorities and seek independent professional advice where needed.

Reviewed by The Quote Yard Editorial Team

Published 16 November 2026 ·

How The Quote Yard Works

We connect you with independent local tradies and service providers, we don't perform any trade work ourselves. Tradies provide their own quotes directly to you. Always confirm licensing, insurance, and scope of work before engaging any provider.

Service availability may vary in regional WA. Verify licences at WA Building and Energy.
Prices are estimates based on typical Bunbury and South West painting rates in 2027. Your final price will depend on the size of the job, surface condition, access and paint system, so compare written quotes that list preparation, coats, paint brand and any travel fee separately.
Need work done? Get free quotes. Post a Job – It's Free