Need Solar Panels Cleaned in WA?

Tell us your suburb or town, the number of panels, how many storeys the house has and what the roof is made of, and local cleaners can quote.

Get Free Solar Panel Cleaning Quotes

Solar Panel Cleaning Prices Across WA

Single-storey array, about 20 panelsPriced on quote
Two-storey or steep roof arrayPriced on quote
Large array or several roof facesPriced on quote
Rust or hard-water stain treatmentPriced on quote
Bird mesh around the arrayPriced on quote
Gutter clean, single storey$150 - $350
Gutter clean, double storey$300 - $650
Window clean, single-storey house$150 - $300
Edge protection, one side only$450 - $1,400
Roof anchor and harness line$450 - $1,200

These are 2027 estimates for typical WA homes, and the panel clean itself is priced on quote. The related roof job figures come from WA gutter, window and edge protection guides, so confirm every price in writing.

Solar Panel Cleaning Services WA - Get Local Quotes

Solar panel cleaning removes dust, salt, bird droppings, ash and mineral spots from the glass of your array, the group of panels on the roof, so more light reaches the cells. In Western Australia three sets of rules apply to the job, and householders rarely see them side by side. WorkSafe WA sets how a cleaner manages the risk of a fall, and its rules for high risk construction work, which includes work with a fall of over 2 metres, changed on 1 October 2026. Building and Energy, the state's building and electrical safety regulator, treats the array as live equipment, because panels keep producing voltage in daylight even after the main switch on your switchboard is turned off. Water matters too, since water from a garden bore, a private well, can leave rust stains, and country scheme water, the public mains supply, often carries more minerals than Perth's. Older homes may have asbestos cement roofing, often called fibro, under the array, and WA rules ban cleaning it with high pressure water. Rural homes that drink from rainwater tanks also need the rinse water kept out of the tank until the roof runs clear. The clean itself is priced on quote across Western Australia, but related roof jobs do have published 2027 estimates. Owners also need to know the shutdown steps, maker limits on water, cyclone season timing and the rules on nesting birds and doorstep selling. Post your job on The Quote Yard and we will connect you with local panel cleaners across Western Australia who can quote on it.

Solar Panel Cleaning Around Western Australia

Panel cleaners work across Perth, Peel, the South West, the Great Southern, the Wheatbelt, the Goldfields and the north of the state. Prices depend on roof access, soiling, the water supply and the distance a crew must travel to reach you.

Get Free Quotes

Solar Panel Cleaning Costs at a Glance, WA 2027

Job Price Range How It Is Charged What Moves the Price Who Can Do It
Single-storey array clean Priced on quote Per visit or per panel Panel count and soiling Panel cleaner
Two-storey array clean Priced on quote Per visit Access gear needed Panel cleaner
Rust or hard-water stain work Priced on quote Add-on per array Age of the marks Panel cleaner
Bird mesh Priced on quote Per array Array shape and roof type Panel cleaner or installer
Gutter clean, single storey $150 - $350 Per visit Leaf load and downpipes Gutter cleaner
Gutter clean, double storey $300 - $650 Per visit Height and access Gutter cleaner
Window clean, single-storey house $150 - $300 Per visit Windows and screens Window cleaner
Window clean, two-storey house $280 - $550 Per visit Height and number of windows Window cleaner
Edge protection, one side $450 - $1,400 Per installation Run length and hire time Edge protection supplier
Roof anchor and harness line $450 - $1,200 Per installation Roof structure Height safety installer
System check or wiring fault Separate quote Per visit Size of the system Licensed electrician

What Adds to a Panel Cleaning Visit

What is involved
A second storey, or a roof steep enough to need rails or a harness, a body strap clipped to a roof anchor.
Rust or hard-water marks that need soaking, careful brushing and a second rinse.
Travel to a regional town, sometimes with an overnight stay for remote jobs.
Gutters, windows and bird mesh added to the same visit as separate items.
Ask every cleaner to list the panel count, access method, water source, each extra and any travel fee on separate lines.

Panel Cleaning in WA: Glass, Wiring and a Roof to Work On

A solar panel clean is mostly glass work, but it happens on a roof beside live wiring, which sets it apart from washing windows at ground level. The cleaner removes the film of dust, salt, pollen and droppings that stops sunlight reaching the cells sealed under the glass. Most crews use soft brushes and purified water on a long pole, and some work from the roof itself when the array cannot be reached from below. Western Australian homes add their own complications, including bore water stains, hard country water, old asbestos cement roofs and long drives to regional towns. For an overview of every household cleaning trade in the state, start with the WA cleaning services hub.

Before quoting, a careful cleaner will ask how many panels you have, how many storeys the house has, what the roof is made of and how steep it is. They will also ask whether you collect rainwater from that roof, because runoff from the clean can find its way into the tank. Photos taken from the ground or from an upstairs window usually give enough detail for a first price. Many households book the panel clean alongside other outdoor jobs, so the same crew may also quote roof cleaning or gutter cleaning while their ladders are already up.

Why WA Solar Cleaning Is Priced on Quote for 2027

No published WA figure exists for a standard panel clean, so this guide lists solar panel cleaning as priced on quote rather than guessing a number. Each WA quote depends on the panel count, the roof height and pitch, meaning how steep it is, the type of soiling and the distance from the cleaner's base. A single-storey array of about twenty panels in a Perth suburb is a very different job from a steep two-storey roof near the coast or a farmhouse array in the Wheatbelt. Several related roof jobs do have 2027 estimates for WA, and they help you check the parts of a quote that combines several jobs. A single-storey gutter clean is about $150 to $350, and a double-storey gutter clean is about $300 to $650.

Window cleaning on a single-storey house with ten to twenty windows is about $150 to $300, and a two-storey house is about $280 to $550, based on the WA window cleaning figures. Where a steep or high roof needs guardrails, waist-high rails that stop a fall, along one side, edge protection for a gutter or solar run is about $450 to $1,400. A temporary roof anchor and harness line, which the worker clips onto, is about $450 to $1,200 when rails are not used. These 2027 estimates help you test a combined quote, but the panel clean itself should always appear as its own line. Ask each cleaner to separate the panel price from gutters, windows and access gear so you can compare the same items. Where no figure exists for your type of job, treat any number given over the phone as a rough guide until the cleaner has seen photos of the roof.

Item 2027 WA Estimate How It Is Charged What Changes the Price
Single-storey array, about 20 panels Priced on quote Per visit or per panel Roof pitch and soiling
Two-storey or steep roof array Priced on quote Per visit Access method and safety gear
Large array or several roof faces Priced on quote Per panel Number of faces to reach
Rust or hard-water stain treatment Priced on quote Add-on per array How long the marks have built up
Bird mesh around the array Priced on quote Per array Panel layout and roof type
Gutter clean, single storey $150 - $350 Per visit Leaf load and downpipes
Gutter clean, double storey $300 - $650 Per visit Height and roof access
Window clean, single-storey house $150 - $300 Per visit Number of windows and screens
Edge protection, one side only $450 - $1,400 Per installation Length of the run and hire time
Temporary roof anchor and harness line $450 - $1,200 Per installation Roof structure and fixing points

Sharing Ladders and Rails Across Several Roof Jobs

Cleaners in WA usually price panels either per visit for a typical home array or per panel for larger systems, and both methods can be fair. A per-visit price suits a single roof face that can be reached safely from one set-up point. A per-panel price suits arrays spread across several roof faces, sheds or patios, because each extra face adds set-up time and another safety check. Whichever method is used, the quote should state how many panels are included and whether any are left out because they cannot be reached safely.

Booking jobs together saves money when the crew already has ladders, rails or a harness line in place for another job. Gutters are the most common pairing, since leaves and grit from blocked gutters often blow back onto the lowest row of panels. Some homeowners add a house washing service in the same week so the whole exterior looks finished at once. Others pair the visit with indoor jobs such as an oven cleaning service when they are preparing a home for sale or a lease handover. Keep each item on a separate line so you can drop one without the other prices changing.

Line Items on a Panel Cleaning Quote

$450 to $1,400, for edge protection along one side of a roof, such as a gutter or solar run, as a 2027 estimate
Line on the quote
What to check
Panel count
Number cleaned and any left out
Access method
Ladder, rails, harness or pole from the ground
Water
Purified, filtered or tap, and where it comes from
Extras
Gutters, windows or bird mesh priced separately

Travel to regional towns should appear as its own clearly labelled line.

A per-panel rate means little until you know the exact panel count.

Ask whether the price changes if the cleaner arrives and decides the roof cannot be accessed safely on the day.

Regulation 79, Guardrails and Harnesses on a WA Home Roof

A cleaner working on or near your roof is at a workplace under safety law, and the business must manage the risk of anyone falling. Guidance from WorkSafe WA explains that the Work Health and Safety (General) Regulations 2022 require businesses with safety duties to manage fall risks under regulations 78, 79 and 80. Regulation 79 sets specific measures, and it took effect for high risk construction work in Western Australia on 1 October 2026. Until 30 September 2026 the older rule required set controls where a person could fall two metres from places such as scaffolds, or three metres from any other edge. WorkSafe notes that regulation 79 does not prescribe a height, so its measures no longer start at a set number of metres.

Regulation 79 sets an order of preference for protecting workers who cannot avoid the risk of a fall. A fall prevention device such as a guardrail comes first, then a work positioning system, ropes that keep a worker in place, and then a fall arrest system such as a harness. WorkSafe's information sheet on roofs in housing construction notes that the risk of falling increases once a roof pitch passes 26 degrees. The same sheet lists a fragile or brittle roof as a hazard, which matters on older WA homes with cement sheeting or clear roofing panels. Inspectors say they expect to find a genuine effort to manage the risk of falls from height, not paperwork alone. Harness work needs a suitable anchor point on the roof, so ask whether one already exists or must be fitted, since that changes both the price and the timing.

As the householder, you are not expected to design the cleaner's safety plan, but you can ask sensible questions before you book. Ask how the crew will reach the panels, whether anyone will walk on the roof, and what happens if wind or heat makes the roof unsafe. Many crews clean single-storey arrays from the ground or a ladder with a long water-fed pole, which avoids standing on the roof at all. For steeper or higher roofs, a cleaner may hire roof edge protection or a mobile scaffold tower, a wheeled work platform, and include that cost in the quote.

Situation What WorkSafe Material Says Common Control Question to Ask
Single storey, low pitch Fall risks must still be managed Pole from the ground or ladder Will anyone stand on the roof?
Two-storey roof edge A 2 metre fall marks high risk construction work Edge rails or scaffold Are rails included in the price?
Pitch above 26 degrees Risk of falling increases Rails with mesh or a harness system Who fits the anchor points?
Fragile or brittle roof Listed as a roof hazard No walking on the sheeting How will they reach the far panels?
Fall of 3 metres or more Written procedures or signs alone not permitted Physical barrier or harness What equipment comes on the day?
Ladder access Ladder check listed as a risk factor Ladder tied at the top and held at the base Who secures the ladder?
Rescue planning Regulation 80 covers emergency and rescue Second person on site What happens if someone falls?

Building and Energy Shutdown Steps Before Anyone Climbs Up

Solar panels produce direct current, known as DC, whenever light falls on them, and that power runs through cables to the inverter. The inverter is the box that converts DC into the alternating current, or AC, used by the lights and appliances in your home. Building and Energy warns that panels keep generating voltage during the day even when the main power is off or the system is shut down. Its home electrical safety guidance also says that turning off the main switch at the switchboard does not cut the power in the solar cabling. That is why a cleaner should never open junction boxes, the sealed boxes on the back of each panel, unplug connectors or move cables, and why any wiring fault belongs with a licensed electrician.

The same guidance asks owners to shut a system down, using the shutdown procedure, the step-by-step list posted at the inverter or main switchboard, before anyone accesses the roof, gutters or panels. Following the posted steps in the right order matters, because getting them wrong may damage the system. If any part of the system looks damaged, do not switch it off yourself, and call a licensed electrical contractor, a business licensed to carry out electrical work, or your installer instead. Building and Energy also recommends a check of the system annually, or as the maker recommends, by an accredited installer or licensed electrician. A WA electrical safety inspection is a separate job from cleaning, but booking both in the same season keeps the roof visits close together. Note the shutdown steps and where each isolator, a switch that cuts power between parts of the system, is located so future visitors can find them.

Shutdown and Safety Checks

Item
What to check
Shutdown procedure
Posted at the inverter or switchboard
DC isolator
Brand checked against recall notices
Cracked or scorched panel
Leave it and call an electrician
Cooling vents
Clear of leaves and dust

Building and Energy lists several recalled DC isolator brands on its home safety page.

Owners can check their isolator brand and model with Product Safety Australia.

Panels still produce voltage in daylight after shutdown, so nobody should touch cables, plugs or junction boxes during a clean.

Hard Scheme Water in Country Towns and Spots on the Glass

Water Corporation explains that hardness measures the calcium and magnesium salts in water, so hard water has more of them, and they stay behind when it evaporates. On glass, hardness shows up as spots, the same marks people notice on shower screens and drinking glasses. The Perth metropolitan scheme meets national guidelines for hardness, but country customers are more likely to have hard water because their supply comes mainly from groundwater. Rinsing panels with hard water and letting it dry in strong sun can leave a fine mineral film across the glass. You can ask Water Corporation about the hardness in your own town by calling its faults line on 13 13 75.

Unger makes DI-Pure and RO-Pure water filters, the kind many panel cleaners carry to strip dissolved minerals from water before it reaches the brush. Trina Solar's user manual for its Vertex modules, the maker's word for panels, recommends soft water, meaning water low in minerals, and sets a limit of 600 milligrams per litre of calcium carbonate. The same manual asks for water with a pH, the scale of how acidic or alkaline it is, between 6 and 8, which is close to neutral. Ask each cleaner where their rinse water comes from, especially outside Perth, where Water Corporation says hard water is more common.

Water Source What It Can Leave Use on Panels? Note
Purified water with minerals removed Very little residue Preferred by most cleaners Carried in the cleaner's tank
Perth scheme water Some spotting if left to dry Possible with prompt drying Meets national hardness guidelines
Country scheme water More mineral spots Ask the cleaner to filter it Mostly supplied from groundwater
Garden bore water Rust and salt stains Avoid on panels Iron reacts with air
Rainwater tank water Leaves, grit or droppings Filter before use Tank screen and first flush matter
Water with detergent Film and streaks Only if the maker allows it Check the maker's manual
Water with solvents Damage to the module Never Trina rules out acetone and strong acids
Steam Heat stress on the glass Never Trina rules out steam cleaners

Rust Marks, Salt Crust and Other Deposits Seen in WA

Be Groundwater Wise, the state's garden bore program, explains that dissolved iron in groundwater reacts with air at the surface and leaves a red rust coat. It names paths, buildings and fences as surfaces it often stains, and a low array on a patio or garage roof can catch the same sprinkler overspray. The program says correctly installed sprinklers that avoid overspray and run-off prevent staining, and its Perth groundwater map shows iron staining risk by area. HealthyWA adds that bore water may stain surfaces because of its dissolved salts and metals. Rust marks on the roof itself are handled in the WA roof cleaning guide, so the advice here stays with the glass.

Coastal homes collect a film of salt that dries to a dull, slightly gritty layer on the panels. Salt dissolves readily in fresh water, so it is usually one of the simpler deposits for a cleaner to lift. The bigger concern near the sea is the aluminium frames and fixings, which a cleaner can check for white powdery corrosion while working. Any loose clamps or rails should be reported to your installer rather than tightened by the cleaner on the day.

Inland and northern homes face fine red dust, while farming districts see chaff, grain dust and soil lifted by machinery and wind. Fine dust tends to settle evenly and may partly wash away in heavy rain, whereas pollen mixed with morning dew can dry hard onto the glass. Bird droppings are the most stubborn spot deposit, because a single dropping shades part of a cell instead of spreading thinly. Lichen and moss can grow along the lower frame edge on shaded or damp roofs in the South West. Each deposit calls for a different amount of soaking and brushing, which is why cleaners ask for close photos before quoting.

Huawei makes SUN2000 inverters and the FusionSolar app, and an inverter's monitoring app is the most reliable way to tell whether dirt is costing you power. Compare production on two similar clear days, one before the clean and one after, so cloud cover does not distort the result. Fronius makes the GEN24 and GEN24 Plus inverters, along with the Reserva battery for storing solar power. SMA makes solar and battery inverters and runs Sunny Portal, its website where owners can check how a system is performing. Enphase makes IQ9 microinverters, which sit beneath individual panels, and offers the Enphase App for owners. GoodWe makes home inverters that connect to the power grid and offers the SEMS Monitoring Portal for its systems.

Deposit Where It Is Common Cleaning Approach Note
Red rust staining Homes using garden bores Stain treatment, priced on quote Fix sprinkler overspray first
Salt film Coastal suburbs and towns Purified water rinse and soft brush Check frames for corrosion
Fine red dust Inland and northern regions Soak, then brush gently Can return quickly after wind
Farm and harvest dust Grain growing districts Soak and brush Timing after harvest helps
Bird droppings Arrays with perches nearby Soak before brushing Never scrape with a blade
Lichen and moss Shaded, damp South West roofs Soft brush along frame edges Check the maker's manual first
Mineral spots Hard-water areas Purified water rinse Left by tap water drying

What Panel Makers' Manuals Say About Cleaning

Panel makers publish cleaning limits in their installation or user manuals, and a careful cleaner follows the manual for your brand. Trina Solar makes the Vertex S+ and Vertex N series modules, and its Vertex user manual sets out detailed cleaning rules. It allows a dry or wet soft cloth, sponge or soft bristled brush, and asks for tools that are non-conductive and will not scratch the glass or frame. It recommends a maximum water pressure of 4 MPa (a pressure unit), also written as 40 bar, and keeps the gap between water temperature and module temperature within minus 5 to plus 10 degrees. The manual also says not to clean during the hottest part of the day, to avoid stress on the glass from a sudden change in temperature.

The same manual rules out steam cleaners, alkaline cleaners, strong acids and solvents such as acetone, and it forbids stepping or standing on the modules. LONGi makes the Hi-MO 7, Hi-MO 9 and Hi-MO X10 modules, so owners of those panels should read LONGi's own manual rather than assume the rules match. Gerni makes high pressure washers, and any pressure washer setting should be checked against the limit in your panel manual before it goes near the glass. Kärcher makes a Window Vacuum for household glass, which is handy for doors and windows but is no substitute for a panel clean. Keep a copy of the manual with your solar paperwork so you can send it to cleaners when you ask for quotes. If the manual is lost, the brand and model are normally printed on a label on the back of each panel, and the installer's handover pack may hold a copy.

Limits From One Maker's Manual

4 MPa, the recommended maximum water pressure in Trina Solar's Vertex series user manual, also written as 40 bar
Manual point
Stated position
Water pH
Between 6 and 8
Water hardness
Up to 600 mg/L of calcium carbonate
Tools
Soft cloth, sponge or soft bristled brush
Steam cleaner
Not to be used
Standing on modules
Forbidden during cleaning
Read the manual for your own panel brand, because cleaning limits differ between makers and between product series.

The WA Ban on Pressure Water Over Asbestos Cement

Many older WA houses have roofs or patio covers made from asbestos cement sheeting, often called fibro, and some of them now carry solar panels. WorkSafe WA has issued a safety alert stating that high pressure water cleaning of asbestos cement material is prohibited. The alert cites the Occupational Safety and Health Regulations 1996 and the Health (Asbestos) Regulations 1992, which local governments administer. WA Health guidance adds that pressure water or air equipment on asbestos cement sheeting is also prohibited under the Work Health and Safety (General) Regulations 2022. Runoff from a panel clean lands on the sheeting below, so the cleaning method must suit the roof as well as the glass.

The WorkSafe alert notes that asbestos cement roofing may be prepared with non-abrasive methods, which do not scrub or wear the surface, such as cleaning solutions washed off with low-pressure water. For a panel clean, that points to a soft brush and a gentle rinse, with no high pressure nozzle aimed at the sheeting and nobody walking on brittle sheets. If the roof is in poor condition, ask an installer whether the panels should come off first, and get advice on asbestos roof removal before any roof work starts. Where a roof has already been pressure cleaned, WA Health guidance says affected areas should be kept wet, left alone and closed off, and local government can direct a clean-up.

Roof Material Risk During a Clean Suitable Method Who Helps
Steel sheet roofing Slippery when wet Pole or harness, soft brush Panel cleaner
Concrete or terracotta tile Cracked tiles underfoot Avoid walking on tiles Panel cleaner, roofer for repairs
Asbestos cement sheeting Fibres released by pressure or impact Low-pressure rinse, no walking Licensed asbestos removalist if damaged
Asbestos cement patio cover Brittle and hard to judge from above Clean from a ladder or below Panel cleaner
Clear roofing or skylights Cannot bear a person's weight Mark and avoid Panel cleaner
Low-pitch steel deck Water pooling near the panels Slow rinse and a squeegee on the glass Panel cleaner
Damaged or sagging roof Unsafe access No clean until repaired Roofer or builder

Drinking Water Tanks and HealthyWA Roof Catchment Advice

Rural and semi-rural WA homes often use water from tanks filled by the same roof the panels sit on. HealthyWA advises keeping roof catchments (the roof areas that feed rain into the tank), gutters and downpipes clean and clear of leaves, and fitting a first flush device. A first flush device diverts the first portion of roof runoff, which carries most of the dirt, away from the tank. HealthyWA also asks owners to follow correct procedures so that work on the roof does not contaminate the rainwater. For roof-mounted hot water work it says to disconnect the pipe to the tank, and asking for the same step during a panel clean is a sensible precaution.

Bird and small animal droppings are among the contaminants HealthyWA lists for roof catchments, and they are also the deposit panel cleaners spend most time on. Removing overhanging branches and potential bird perches helps both the tank and the panels. Ask the cleaner to use plain water on a tank-fed roof, and ask for the Safety Data Sheet, the supplier's hazard document, for any product they still want to use. Clean the gutters in the same visit so dislodged grit does not wash into the tank screen at the next rain. A gutter guard installation can reduce leaf build-up, but it does nothing about dust settling on the glass. Where the tank supplies drinking water, ask the cleaner to wait until the downpipe is disconnected before wetting any part of the roof.

After a bushfire, HealthyWA says tank water can be contaminated by ash, smoke and fire suppressant water landing on the roof. Its advice is not to reconnect the downpipes until the roof and gutters have been cleaned. It also says the first good rainfall after a fire should be left to drain away rather than collected. A panel clean after a nearby fire is a good time to plan that sequence with the cleaner, so the rinse water and the first rains both bypass the tank.

Tank-Fed Roof Checklist

First good rain, the rainfall HealthyWA says should drain away after a fire before tank collection resumes
Step
When
Disconnect the tank downpipe
Before the rinse starts
Clean gutters and screens
Same visit as the panels
Check the first flush device
After the clean
Reconnect the downpipe
Once runoff runs clear
Ask for plain water on a tank-fed roof unless the cleaner can show a product is suitable for a drinking water catchment.

Pilbara and Kimberley Arrays Around Cyclone Season

Building and Energy's cyclone safety guide says cyclone season in North West Australia typically runs from November to April. Homes in towns such as Karratha, Port Hedland and Broome therefore have limited time for routine roof work each year. Cleaning before November lets the crew look over frames, clamps and roof fixings while conditions are calmer and access is easier. Any loose rail, cracked glass or lifted clamp spotted during the clean should go straight to your installer rather than being patched by the cleaner. The Shire of Broome reminds residents that installing panels there needs a building permit, which shows how closely mounting work is controlled.

After a cyclone, the guide warns people to avoid contact with exposed electrical items, including solar panels, and to stay at least 8 metres from fallen power lines. Storm-damaged panels can still produce voltage in daylight, so clearing debris off a damaged array is not a job for a cleaner. Have a licensed electrician or your installer inspect the system first, and book the clean only once they confirm it is safe. Red dust that settles after a storm is easier to remove once the roof has dried and the wind has dropped. Northern call-outs often involve long travel, so ask whether a quote shows travel and any accommodation as separate lines. Owners who are away for part of the year can ask a neighbour or property manager to photograph the array after a storm, so the electrician knows what to expect.

North West Season Plan

November to April, the months Building and Energy says cyclone season typically runs in North West Australia
Item
What to check
Pre-season clean
Booked before November
Frames and clamps
Reported to the installer if loose
After a cyclone
Electrician checks before any clean
Travel
Shown as its own line on the quote
Stay clear of damaged panels after a storm, because they can still produce dangerous voltage whenever light reaches them.

Cracked Glass, Scorch Marks and Panels Not to Clean

A panel clean also gives the cleaner a close look at the array, and some findings mean the cleaning should stop. Trina Solar's manual warns that cracked or broken modules carry a risk of electric shock from leakage current, electricity escaping through the damage, and that wet modules increase the risk. Scorch marks, melted plastic near cables, brown discolouring under the glass and a burning smell are all reasons to stop and call an electrician. Building and Energy lists water seepage, worn cable insulation, corrosion and damage from vermin and storms among the common problems with solar systems. A good cleaner photographs anything unusual and sends the photos to you rather than trying to fix it.

Vermin such as rats can chew cable insulation under the array, and droppings or nest material often show where they have been. If the cleaner finds chewed cables, the next call is to an emergency electrician or your installer, not a pest controller first. Once the wiring is made safe, pest control can deal with any rodents in the roof space, and sticking with this order protects everyone who later works near the array. Building and Energy's advice never to attempt electrical repairs yourself applies to cleaners just as much as to owners.

Finding What It May Mean Clean Today? Who to Call
Cracked or shattered glass Shock risk when wet No Installer or electrician
Scorch or burn marks Overheating at a cell or connection No Licensed electrician
Chewed cable insulation Vermin damage No Electrician, then pest controller
Loose clamps or rails Mounting fault Only around it, if safe Installer
Water inside a panel Seal failure No Installer
Discoloured cells Possible ageing or fault Yes, then report it Installer for warranty advice
Heavy, even dust Normal soiling Yes Panel cleaner
Native bird nest Protected fauna Not near the nest DBCA wildlife licensing

Native Birds Under the Array and the Take or Disturb Rule

The gap under a panel array gives birds shade and shelter, and nests there bring droppings, nest material and noise. Before anyone removes a nest, find out what kind of bird is using it, because native birds are protected in Western Australia. Guidance from the Department of Biodiversity, Conservation and Attractions states that a person must not take or disturb native fauna, meaning kill, catch or interfere with native animals, without lawful authority. The same guidance asks for careful consideration during breeding and nesting seasons when birds are being moved on. If a native bird is nesting under your panels, contact DBCA through its wildlife licensing team before the cleaner touches the nest.

Mesh fitted around the edge of an array is the usual way to keep birds out once any nest has been dealt with lawfully. Bird mesh is priced on quote in WA, because no published state figure exists and the cost depends on the array's shape and the roof type. Ask whether the mesh clips to the panel frames or is fixed some other way, and check your panel manual before agreeing to any drilling. Gorilla makes industrial-grade ladders and height safety gear for trade use, so ask which access equipment the crew will bring. Bailey makes extension ladders and platform stepladders, and a crew using either should tie the ladder at the top and have someone steady its base before climbing. Mesh also needs a look at later cleans, because leaves and droppings can build up behind it and hold moisture against the frame.

Before Anyone Moves a Nest

Step
Why
Identify the bird
Native species are protected
Check for eggs or chicks
Nesting season needs care
Contact DBCA if native
Lawful authority may be needed
Fit mesh once clear
Stops birds returning

DBCA's wildlife licensing team answers questions about protected fauna by email.

Droppings under the array should be cleaned off before any mesh is fitted.

Do not let anyone pull out a nest with eggs or chicks until you know the species and the rules that apply.

Booking a Clean From Perth to Esperance and Kununurra

Western Australia's size makes travel one of the biggest factors in a panel cleaning quote outside Perth. Crews based in Perth often group regional jobs into one trip, so a town visit may cost less when several homes book in the same week. In the South West, many trades are based locally, and the Bunbury and South West electrician guide shows where electricians are based across that region. In the Great Southern and Goldfields, ask whether the crew will travel the day before, since an overnight stay may appear on the quote. Ask whether the cleaner brings purified water, because filling a tank from a hard local supply can leave the very spots the rinse is meant to remove.

Timing matters as much as distance for most WA panel cleans. Afternoon heat makes roofs hazardous and Trina's manual advises against cleaning in the hottest part of the day, so many summer jobs start early. Farming districts may get the best result once harvest dust has settled, while coastal homes may prefer a clean after a run of strong onshore winds. In the north, cleaning before cyclone season leaves time for an installer to follow up anything the cleaner reports. Perth homes with garden bores may want the clean booked after the sprinklers have been adjusted, so fresh rust marks do not appear straight away. Coastal holiday homes are often empty for long stretches, so a clean booked just before the busiest months means the panels are clear when the house is in use.

Area Common Deposits Timing Tip Quote Note
Perth and Peel Dust, pollen and bore staining Early morning in summer Bore overspray fixed first
South West Pollen and lichen on shaded roofs Dry spell after winter Check frames for moss
Great Southern Salt and pollen After windy spells Travel listed separately
Wheatbelt Farm and harvest dust After harvest Group bookings may lower travel
Goldfields Fine red dust Calm weather after wind Overnight stay may be charged
Mid West coast Salt and dust After onshore wind spells Ask about purified water
Esperance and the south coast Salt and wind-blown sand After a run of strong winds Travel and overnight stay listed
Pilbara and Kimberley Red dust after storms Before November Electrician check after cyclones

Damage, Refunds and Consumer Protection WA

Cleaning is not a licensed trade in Western Australia, so there is no cleaning licence number to check, but the consumer guarantees, rights the law gives every customer, still apply. Consumer Protection WA explains that a service provider guarantees to perform services with due care and skill, fit for a particular purpose and within a reasonable time. If a clean leaves the panels streaked or misses part of the array, ask the business to come back and put it right first. Electrical work on the system is different, because it must be done by a licensed electrician working for a licensed electrical contractor. A cleaner who offers to reconnect plugs or replace an isolator is offering electrical work, and needs those licences to do it.

Damage beyond the panels, such as cracked roof tiles, a bent gutter or water through the ceiling, is a separate claim against the cleaning business. Take photos before the crew leaves if you notice anything, and send a written list of the damage promptly. Ask the business for its public liability insurance details, since that cover usually pays for damage to your property. Keep the quote, invoice and any messages together, and if the business offers a repair, agree in writing on who will carry it out and by when.

If the business does not respond, Consumer Protection WA can help you ask for a repair, refund or compensation. Its consumer guarantees pages explain that the remedy depends on whether the problem is minor or major. The ACCC publishes plain guides to consumer guarantees for services, which help when you are wording a complaint. Before going that far, a calm written request that names the problem and the fix you want often settles the matter.

What to Look Out For With Doorstep Solar Cleaning Offers

Door-to-door offers to clean solar panels are common, and the unsolicited selling rules, which cover sales you did not ask for, give you strong protection. The ACCC says door-to-door sellers may visit only between 9am and 6pm on weekdays and until 5pm on Saturdays, and never on Sundays or public holidays. An agreement worth $100 or more made at your door carries a cooling-off period, time to cancel without penalty, of ten business days. Consumer Protection WA explains that during that period the supplier must not provide any services or accept payment. A seller who offers to start the clean straight away, or asks for cash on the spot, is ignoring those rules.

Consumer Protection WA supplies Do Not Knock stickers, which tell sellers not to knock, and a salesperson must leave immediately when asked by the person who lives there. Stickers can be ordered on 1300 304 054 or collected from its Perth office or regional offices in Albany, Bunbury, Broome, Geraldton, Kalgoorlie and Karratha. Be wary of any quote that promises a fixed percentage boost in output, because results depend on how dirty the panels were to begin with. Question any claim that a clean is needed to keep your warranty valid unless the cleaner can point to the clause in your own paperwork. A genuine business will give a written quote with its name, Australian Business Number (ABN) and contact details, and will not pressure you to decide on the spot. If you feel pressured at the door, close it, note the business name and look the company up before agreeing to anything.

Panel Cleaning Quote Checks

Check each quote for
The business name, ABN and a phone number or address you can verify.
The number of panels included and any the crew cannot reach safely.
How the crew will reach the roof and which safety gear comes on the day.
The water used, where it comes from and whether any product is added.
Gutters, windows, bird mesh and travel each priced on separate lines.
No start date inside the cooling-off period after a doorstep sale.

A quoted output gain is only a guess unless it is based on your monitoring data.

Any demand for full payment before work starts deserves extra caution.

Never let a door-to-door seller onto your roof on the day of the visit, however attractive the price sounds.

Getting Quotes From WA Panel Cleaners on One Written Brief

Send every cleaner the same short brief so the prices can be compared. Give the suburb or town, the number of panels, the number of storeys, the roof material and a rough idea of the pitch. Add photos of the array from the ground and from any upstairs window, plus a close photo of the worst marks. Mention a garden bore, a rainwater tank or an asbestos cement roof, because each one changes the method. Say which extras you want priced, such as gutters, windows or bird mesh, and ask for each as a separate line.

Collecting three written quotes gives a fair comparison, and a short call about water, roof access and damage tells you a lot about how each cleaner works. Battery owners should mention their system too, since Building and Energy's checklist covers battery storage alongside the panels. Tesla makes the Powerwall 3P home battery, and Sigenergy makes the SigenStor energy storage system, so name your battery brand in the brief. A cleaner does not service batteries, but knowing the layout helps them plan the shutdown with you.

If you are in Perth and want help with other household jobs at the same time, regular and one-off cleaning help is set out in the Perth cleaner hiring guide. For array changes, extra panels or a new inverter, talk to a solar panel installation business rather than a cleaner. Businesses with larger rooftop systems can read the commercial solar installation guide, since big arrays need their own access planning. After the clean, check your monitoring on a clear day and compare it with a similar day before the visit. Keep the cleaner's report and photos with your solar paperwork for the next time the panels need attention.

Solar Panel Cleaners Across WA

Solar panel cleaning advice on this page applies across Western Australia. Jobs near Perth and the larger regional centres usually have more cleaners available, while remote towns may need a crew to travel and group several homes into one trip.

▶ Perth 28 areas
Perth CBD Joondalup Wanneroo Butler Alkimos Stirling Scarborough Hillarys Karrinyup Morley Bayswater Bassendean Belmont Victoria Park South Perth Melville Applecross Canning Vale Willetton Cannington Fremantle Cockburn Rockingham Baldivis Gosnells Armadale Byford Ellenbrook
▶ Mandurah & Peel 20 areas
Mandurah Halls Head Dawesville Falcon Erskine Silver Sands Madora Bay San Remo Greenfields Meadow Springs Lakelands Coodanup Pinjarra Ravenswood Waroona Dwellingup North Dandalup Serpentine Jarrahdale Boddington
▶ Bunbury & South West 24 areas
Bunbury Australind Eaton Dalyellup Gelorup Capel Busselton Vasse Dunsborough Yallingup Margaret River Cowaramup Augusta Harvey Brunswick Junction Collie Donnybrook Balingup Nannup Bridgetown Boyup Brook Manjimup Pemberton Northcliffe
▶ Swan Valley & Perth Hills 24 areas
Guildford Midland Herne Hill Middle Swan West Swan Upper Swan Caversham Baskerville Henley Brook Swan View Helena Valley Kalamunda Gooseberry Hill Lesmurdie Walliston Carmel Pickering Brook Mundaring Glen Forrest Darlington Parkerville Chidlow Roleystone Bedfordale
▶ Avon Valley & Wheatbelt 22 areas
Northam York Toodyay Beverley Bakers Hill Clackline Wundowie Goomalling Dowerin Wongan Hills Cunderdin Tammin Kellerberrin Merredin Wyalkatchem Trayning Nungarin Quairading Brookton Corrigin Bruce Rock Narrogin

Solar Panel Cleaning FAQ

Is there a standard WA price for cleaning a home solar array?
No published WA figure exists for a standard panel clean, so this guide does not invent one. Each quote depends on the number of panels, the roof height and pitch, the soiling and the travel involved. Related roof jobs do have 2027 estimates, such as about $150 to $350 for a single-storey gutter clean. Ask each cleaner to list the panel clean separately from gutters, windows and access gear so the totals compare fairly.
Should my system be shut down before the cleaner starts?
Building and Energy says to shut the system down, using the posted procedure, before anyone accesses the roof, gutters or panels. Follow the steps in the order shown at the inverter or switchboard, because the wrong order may damage the system. Panels keep producing voltage in daylight even after shutdown, so nobody should touch cables or connectors. If anything looks damaged, leave the system as it is and call a licensed electrician or your installer.
Can bore water from my garden be used to rinse the panels?
Garden bore water is best kept off the glass of your solar panels. Be Groundwater Wise explains that dissolved iron in groundwater reacts with air and leaves a red rust coat on surfaces. HealthyWA also notes that bore water may cause staining because of its dissolved salts and metals. Ask the cleaner to bring purified water, and adjust any sprinklers that spray onto low panels or patio roofs.
Our town's tap water leaves white spots, is it fine for rinsing panels?
Water Corporation says country customers are more likely to have hard water because most of their supply comes from groundwater. Hard water leaves calcium and magnesium spots behind as it dries, which can dull the glass. Trina Solar's manual recommends soft water with no more than 600 milligrams per litre of calcium carbonate. Ask whether the cleaner purifies the water, and call Water Corporation on 13 13 75 to ask about your local hardness.
Is a pressure washer ever allowed near panels on a fibro roof?
No, because WorkSafe WA states that high pressure water cleaning of asbestos cement material is prohibited. Its safety alert describes cleaning solutions washed off with low-pressure water as a non-abrasive method for roof sheeting. For panels, that means a soft brush and a gentle rinse, with nobody walking on the brittle sheets. If the roof has already been pressure cleaned or damaged, keep the area wet and undisturbed and contact your local government for advice.
We drink tank water from this roof, what should happen on cleaning day?
Disconnecting the tank downpipe is a sensible step when you collect water from the same roof as the panels. HealthyWA asks owners to follow correct procedures so that roof work does not contaminate tank water. Disconnect the downpipe before the rinse and reconnect it once the runoff runs clear. Check the first flush device and the tank screen afterwards, since grit from the panels and gutters can collect there.
Which WA licence should I ask a panel cleaner to show me?
None, because WA has no licence for cleaning panels, so check the business name, ABN and insurance instead. Electrical work on the system is different and must be done by a licensed electrician working for a licensed electrical contractor. A cleaner should not open junction boxes, unplug connectors or replace isolators. Ask for a certificate of currency, the insurer's proof that public liability cover is active, before anyone goes up on the roof.
What changed for roof work in WA on 1 October 2026?
From that date, regulation 79 of the Work Health and Safety (General) Regulations 2022 applies to high risk construction work in WA. It sets an order of controls, starting with fall prevention devices such as guardrails. Unlike the older rule, regulation 79 does not prescribe a height at which it starts to apply. WorkSafe WA says inspectors expect to see a genuine effort to manage the risk of falls from height.
A door knocker offered to clean my panels today, can they start straight away?
Not if the agreement is worth $100 or more and was made at your door. Consumer Protection WA says the supplier must not provide services or accept payment during the ten business day cooling-off period. The salesperson must also leave immediately if you ask them to go. Get written quotes from other cleaners and compare them before you agree to anything.
Is it legal to pull a native bird's nest out from under the array?
Not without checking first, because native birds are protected in Western Australia. DBCA guidance says a person must not take or disturb native fauna without lawful authority. If a native bird is nesting there, contact DBCA's wildlife licensing team before anything is moved. Once the space is clear, mesh around the array can stop birds returning, and it is priced on quote.

Roof and Solar Specialists WA

For Trades & Contractors - WA

Solar panel cleaning often connects with other roof and electrical work. Electricians handle shutdowns, faults and isolators, roofers repair tiles and sheeting, and scaffold suppliers provide safe access for higher roofs.

Compare Solar Panel Cleaning Quotes

Tell us your suburb or town, the number of panels and your roof type, then compare quotes from local solar panel cleaners.

Get Free Solar Panel Cleaning Quotes

About This Guide

This page provides guidance information only. Details may change, always verify with the relevant authorities and seek independent professional advice where needed.

Reviewed by The Quote Yard Editorial Team

Published 20 November 2026 ·

How The Quote Yard Works

We connect you with independent local tradies and service providers, we don't perform any trade work ourselves. Tradies provide their own quotes directly to you. Always confirm licensing, insurance, and scope of work before engaging any provider.

Service availability may vary in regional WA. Verify licences at WA Building and Energy.
Prices are 2027 estimates for typical WA homes. Solar panel cleaning itself is priced on quote, so compare written quotes that list the panel count, access method, water source, travel and each extra separately.
Need work done? Get free quotes. Post a Job – It's Free