Looking for a Plasterer in Adelaide?

Tell us your suburb, the rooms involved, whether the walls are stone, brick or plasterboard, the age of the house and what needs fixing or replacing. We will pass that description to local plasterers across the metropolitan area, so every quote you receive is based on the same details.

Get Free Plastering Quotes

Adelaide Plastering Price Guide

Small hole patch, up to 50 mm$50 - $100
Minimum call-out for small repairs$150 - $250
Crack repair, per lineal metre$25 - $50
Plasterboard walls, supplied and fixed$45 - $70 per m²
Plasterboard ceiling, supplied and fixed$55 - $85 per m²
Sagging ceiling re-fixed$45 - $75 per m²
Lath and plaster repair$100 - $200 per m²
Gypsum cove cornice, fitted$8 - $22 per lm
Single room, walls and ceiling$1,500 - $3,000
Period ceiling restored, per room$3,000 - $10,000

These are estimated Adelaide price ranges for 2027. Your price depends on the type of wall or ceiling, the access and the number of coats and visits needed. Fixing a roof leak, salt damp or asbestos before plastering adds to the total.

Hire a Plasterer Adelaide SA - Get Local Quotes

Adelaide has a large stock of older sandstone, bluestone and brick homes whose inside walls were finished with lime render and plaster, soft coats made from lime and sand. Many of their ceilings are lath and plaster fixed to thin timber strips. Those surfaces behave differently from the plasterboard in newer suburbs, so the right repair, and its price, depends on the age of your house. Salt damp, the local name for salty moisture rising up a stone or brick wall, can lift plaster low on old walls and must be fixed at the source before any patch will last. Reactive clay under much of the plains swells and shrinks with the seasons, which can open cracks in cornices, the mouldings where walls meet ceilings, that return after a quick fill. A sagging lath and plaster ceiling can often be re-fixed rather than replaced, which keeps original cornices and ceiling roses, the round centre mouldings, in place and can cost far less. Plastering a home counts as building work under South Australian law, so the business you hire should hold a building work contractor licence from Consumer and Business Services. Homes built before the mid-1980s can also contain asbestos cement sheeting, which should be tested before anyone cuts, drills or sands it. The prices on this page are 2027 estimates for metropolitan Adelaide, drawn from our South Australian plastering guides, and they assume normal working hours and clear access. Post your job on The Quote Yard and we will connect you with local Adelaide plasterers who can quote on it.

Adelaide Plaster Jobs We Cover

Plastering across metropolitan Adelaide ranges from a few patches before a rental inspection to a full lath and plaster ceiling repair in an old stone villa. We can connect you with local plasterers who all price the same written description of your job.

Get Free Quotes

At a Glance - Adelaide Plastering Prices, 2027 Estimates

Job Price Range How It Is Charged What Drives It In Adelaide Who Can Do It
Small hole patch $50 - $100 Per patch Size, backing and paint match Plasterer or patching specialist
Large hole patch $120 - $250 Per patch Backing board and number of coats Plasterer
Crack repair $25 - $50 per lm Per lineal metre Cause of the crack and re-cracking Plasterer
Water damaged section $300 - $800 Per section Leak fixed first, area cut out Plasterer, roofer or plumber first
Plasterboard walls $45 - $70 per m² Per square metre Board type, corners and openings Licensed plastering business
Plasterboard ceiling $55 - $85 per m² Per square metre Ceiling height and roof access Licensed plastering business
Ceiling re-fixing $45 - $75 per m² Per square metre Depth of sag and condition of laths Plasterer with ceiling experience
Lath and plaster repair $100 - $200 per m² Per square metre Lime mix, drying and cornice Heritage plasterer
Salt damp assessment $200 - $450 Fixed fee Wall length and testing Damp specialist
Salt-resistant render $80 - $150 per m² Per square metre Amount of salt and wall height Plasterer or renderer
Cornice run by hand $150 - $400 per lm Per lineal metre Shape detail and mould making Heritage plasterer
Single room, walls and ceiling $1,500 - $3,000 Fixed price Room size and cornice choice Licensed plastering business

What Pushes an Adelaide Plastering Bill Up

What is involved
Lime plaster on stone and brick walls takes longer to mix, apply and harden than modern gypsum plaster. Each coat needs drying time, so the same area can take more visits.
Salt damp has to be treated before replastering. Removing plaster full of salt and waiting for the wall to dry adds stages to the job.
Period cornices and ceiling roses can cost more than the ceiling itself. Matching an old cornice shape may mean making a new mould and running the cornice by hand in wet plaster.
Older wall and eave sheeting may need asbestos testing first. If it contains asbestos, licensed removal comes before any new board goes up.
Ask every plasterer to list labour, materials, visits, protection and waste removal on separate lines, and to name the board, cornice profile and plaster product. Quotes set out that way can be compared line by line.

Start With the Age and Walls of Your Adelaide Home

Plastering work around Adelaide ranges from a single patch behind a door handle to a full ceiling repair in a nineteenth century villa, and the trade covers very different skills. A plasterer who hangs plasterboard and fills its joints every day may have little experience with lime, and a heritage specialist may not suit a quick rental repair. For the general range of plastering services and statewide price ranges, see our page on plasterers in South Australia. Hiring in Adelaide itself brings older wall types, damp problems, heritage rules and South Australian contract law into a local plastering job. Every price here is a 2027 estimate and should be checked against written quotes for your own home.

Before ringing anyone, work out what your walls and ceilings are actually made of. A plasterboard wall sounds hollow between the studs, the upright frame timbers, when you knock on it, while lime plaster on stone or brick sounds solid and feels cold. A ceiling with long cracks running in parallel lines, or one that dips between the joists, the timber beams that carry it, may be lath and plaster rather than plasterboard sheet. Note the year the house was built if you know it, because that answer shapes the method, the safety checks and the price.

Tenants should not arrange plastering themselves without written agreement from the landlord or property manager. Landlords preparing a rental for new tenants often want quick patches across several rooms, which suits a plasterer who prices per visit. Owners of units in a strata or community title building should check whether a ceiling or shared wall belongs to the strata or community corporation, the owners' body that runs shared areas, before booking work. Sorting out who is responsible first avoids paying for work that someone else should fund.

What Plaster Work Costs in Adelaide in 2027

Small patch repairs are usually the cheapest plastering jobs, with a hole up to 50 millimetres across costing about $50 to $100 by our estimate. Holes between 50 and 150 millimetres run at roughly $80 to $150, and larger holes cost $120 to $250 each. Many plasterers charge a minimum call-out of $150 to $250, so grouping several small repairs into one visit usually saves money. Cracks are often priced at $25 to $50 per lineal metre, which means per metre of crack length. Water stains cost around $80 to $180 to treat once the leak is fixed, and a damaged section that has to be cut out runs at $300 to $800. Patching methods and drying times are explained in our plaster patching guide.

New plasterboard supplied and fixed to walls costs about $45 to $70 per square metre, while ceilings run a little higher at $55 to $85 because the work is overhead. Moisture resistant board, which copes with steam and splashes, costs about $55 to $80, and fire rated board, which slows a fire, costs $65 to $100 per square metre. A single room lined on walls and ceiling usually comes to $1,500 to $3,000 in total. Lath and plaster repairs are much slower, at roughly $100 to $200 per square metre, and restoring a whole period ceiling can cost $3,000 to $10,000. Use the common job prices in the table below to test each quote you receive.

Several local factors push Adelaide plastering prices toward the top of each range. Tall ceilings in older villas need trestles, which are portable work platforms, or scaffolding, which adds set-up time to every visit. Narrow inner suburb streets with no off-street parking make it slower to carry in sheets and carry out waste. Lime work, salt damp and matching an old cornice all add stages, while a new extension lined with standard board usually sits near the bottom of the range. Asking for a room by room breakdown shows where each quote is spending your money.

Job Adelaide Range How It Is Charged What Moves It
Small hole, up to 50 mm $50 - $100 Per patch Finish and paint match
Medium hole, 50 to 150 mm $80 - $150 Per patch Backing needed behind the hole
Crack repair $25 - $50 per lm Per lineal metre Cause and chance of re-cracking
Minimum call-out $150 - $250 Per visit Travel and drying visits
Plasterboard walls $45 - $70 per m² Per square metre Board type and corners
Plasterboard ceiling $55 - $85 per m² Per square metre Height and roof access
Ceiling re-fixing $45 - $75 per m² Per square metre Depth of sag
Lath and plaster repair $100 - $200 per m² Per square metre Lime mix and drying time
Salt-resistant render $80 - $150 per m² Per square metre Amount of salt in the wall
Single room, walls and ceiling $1,500 - $3,000 Fixed price Room size and cornice

Call-Out Minimums, Square Metre Rates and Whole-Room Prices

Plasterers in Adelaide price work in three main ways, and the method can change the total more than the rate itself. Small repairs are usually charged per patch or as a minimum visit, because each patch needs two or three coats with drying time between them. Sheeting work is priced per square metre of board, with extra lines for cornice, corner beads, which are metal or plastic edge strips, and the number of coats. Whole rooms and ceiling replacements are usually quoted as one fixed price after the plasterer has looked inside the roof space.

Several return visits are normal on patch work, since jointing compound, the paste used to fill joints and holes, has to dry before sanding and the next coat. Ask whether the price covers every visit or only the first one. A provisional sum, which is an allowance for a cost that cannot be known yet, often appears where old plaster may come away once work starts. Find out how the plasterer will charge if the real cost goes past that allowance, and whether a margin, an extra percentage for the business, is added. Quotes made up mostly of allowances give little idea of the final bill.

How Adelaide Plasterers Price a Job

What is involved
Per patch or minimum visit pricing suits small holes, dents and cracks in a few rooms.
Square metre rates suit new plasterboard, re-sheeting and ceiling replacements.
Fixed room prices suit a defined job once the plasterer has seen the roof space.
Provisional sums cover unknowns such as loose lime plaster hidden behind a surface that looks sound.
Ask how many visits the price includes, since patch work needs drying time between coats.

Plastering as Building Work Under the CBS Licence System

The Building Work Contractors Act 1995 defines building work to include altering, repairing and improving a building, which covers most plastering in a home. Consumer and Business Services (CBS), the state agency that licenses builders, says a building work contractor licence is needed to carry out building work in South Australia. Each licence carries conditions stating the type of work the holder can contract for, and contracting for work outside those conditions is an offence. A plasterer working as a subcontractor for a builder needs a licence too, although employees of a licensed business do not. Every piece of building work must also be overseen by a registered building work supervisor, a person approved by CBS to supervise work on site. The CBS guidance we read sets no dollar value below which a plastering business can work unlicensed.

You can check a licence on the Consumer and Business Services website before you sign anything. Search by the name or the licence number shown on the quote, and confirm that the conditions cover the work being priced. Contractors doing specified building work, a set of trade categories that includes bricklaying and carpentry, need at least $10,000 in net assets, what the business owns minus what it owes, or a restricted subcontractor licence. CBS lists penalties of up to $150,000 for an individual who carries on business as a building work contractor without the right licence. A larger job that moves or adds walls is usually run by a licensed builder, as set out in our guide to hiring a builder in Adelaide.

Checking an Adelaide Plasterer Before You Sign

What is involved
The name on the quote matches the name on the CBS licence register.
The licence conditions cover the plastering, sheeting or rendering being priced.
Subcontract plasterers hold their own licence, while employees work under the business licence.
A registered building work supervisor oversees the work on site.
A plastering quote with no licence number on it is a reason to ask questions before paying anything.

The $20,000 Contract Line for a Plastering Job

Most plastering jobs in Adelaide cost less than $20,000, which makes them minor domestic building work under the Building Work Contractors Act. On those jobs the deposit is capped at $1,000, according to the Law Handbook published by the Legal Services Commission. A written contract is not required by law below that figure, but a written scope and price still protects both you and the plasterer. Since 10 November 2025, the written contract rules apply to contracts above $20,000, up from the old $12,000 figure. Those contracts must show the contractor's name and licence number, be signed by both parties and come with Form 1, the notice that explains an owner's rights.

Large jobs, such as replastering a whole villa or lining a new extension, can cross the $20,000 line. The deposit is then limited to 5 per cent, and the owner has five clear business days after signing to cancel the contract in writing. Building indemnity insurance, which pays out if the contractor dies, disappears or becomes insolvent, is only required when the work also needs development approval, the formal planning and building approval. Statutory warranties, which are guarantees set by law, apply to every domestic building work contract and can be claimed for five years after the work is finished.

Plastering payments are often staged so that money follows finished work, such as sheets fixed, joints set and the final coat done. Each payment on a contract over $20,000 should be a genuine progress payment, and the Law Handbook notes that an owner need not pay one without a written request from the contractor. Where building indemnity insurance applies, ask for the certificate before paying the deposit, since work cannot start until the insurance is in place. On smaller jobs, a short written agreement listing the rooms, products, visits and price is still worth having. Keep every invoice and receipt with the quote in case a defect appears later.

Contract Value Written Contract Up-Front Limit Cancelling After Signing
Up to $20,000 Not required, still advised $1,000 deposit No cooling-off period
Over $20,000, no approval needed Required, with Form 1 5 per cent deposit Five clear business days
Over $20,000, approval needed Required, plus indemnity insurance 5 per cent deposit Five clear business days
Any domestic plastering job Five year statutory warranties Progress payments on written request Licensed contractor required

Lime Plaster and Render Inside Stone and Bluestone Villas

Older Adelaide homes built of sandstone, bluestone or brick were almost always finished inside with lime render and lime plaster. That is the view of the state's technical note on maintaining older buildings, published by the then Department for Environment and Heritage. Lime is softer than cement and can flex slightly without cracking, which suits walls that move with the seasons on clay. Cement renders and hard plasters are stronger and more brittle, and the note treats their use on old walls with caution. For repairs, it recommends a lime-based render, the thicker base coat, with a set coat, the thin smooth final layer of plaster. A plasterer who proposes gypsum compound or cement render on a stone wall should be able to explain why.

Ask any plasterer you are considering about lime work they have done on similar houses nearby. Lime mixes take longer to harden than gypsum plaster, so a lime repair is usually spread over more visits, and the price reflects that. Cement Australia makes hydrated lime, the dry powdered lime used in traditional mixes, along with a plasterers cement. Mapei makes renders, bedding mortars for laying bricks, and thin skim coats for stone and brick walls. Rockcote makes cement renders and coloured renders, so ask which product suits an old wall before work begins.

Not every wall in an old house is solid masonry, since many villas also have timber-framed internal walls lined with lath and plaster. The technical note describes these walls as hair-reinforced plaster over timber laths, and calls them generally trouble-free. Problems usually start where a wall has been knocked, a doorway has been moved or water has leaked in from above. Patching them calls for the same lime-based approach as a ceiling, with new laths or mesh where the old timber has failed.

Finish Where You Find It Usual Repair Avoid
Lime render and set coat Inside stone, bluestone and brick walls Lime-based render and set coat Hard cement render over old lime
Hair-reinforced lath and plaster Timber stud walls and ceilings Re-fix with screws, patch on laths Filling cracks before finding the cause
Cornice run in wet plaster Period ceilings and roses Repair with a matched profile Swapping in a plain stock profile
Fibrous plaster Prefabricated ceilings, cornices and panels Re-support and patch Leaving it damp or poorly supported
Plasterboard Newer homes and extensions Patch or replace sheets Heavy new sheet under a failed old ceiling

Lath and Plaster Ceilings: Re-Fix, Patch or Replace

A lath and plaster ceiling is made by pushing wet plaster, reinforced with animal hair or natural fibres, up between thin timber strips called laths so it grips them as it sets. Over a century that grip, called the key, can break along a line, and the ceiling starts to sag between the joists. The technical note lists repairs that keep the original ceiling, including re-securing it with screws, filling broken keys with epoxy or new plaster, and patching on existing or new laths. Rust-proofed steel mesh can replace timber laths where keeping the original detail matters less. Each option keeps the cornice and rose in place, which can save far more than the repair costs.

One shortcut is to fix new plasterboard straight under a damaged old ceiling, but the note advises against it because the extra weight can overload the joists. Fibrous plaster, a prefabricated sheet reinforced with natural fibres, is weakened by damp and can sag where its supporting timbers are spaced too widely. A ceiling that has dropped suddenly, cracked across its width or bulged after rain should be kept clear until a plasterer has checked it. Stabilising a failing ceiling costs about $300 to $600 by our estimate, and the repair methods are set out in our sagging ceiling repair guide.

Water stains on a ceiling usually trace back to the roof, so the leak has to be found and fixed before any plaster is replaced. Roofing repairs on older homes are covered in our guide to hiring a roofer in Adelaide. Old plaster coming down can expose termite damage in battens, the timber strips holding a ceiling, which needs inspecting as set out in our guide to hiring a pest controller in Adelaide. Ceiling replacement fills a room with dust and debris, so plan where the furniture will go for a few days. If whole rooms must be emptied, short-term moving help is covered in our guide to hiring a removalist in Adelaide.

Ceiling work in Adelaide often means time in the roof space, which gets very hot on summer afternoons. Ask whether the plasterer prefers early starts for roof space work in summer, since that can affect start dates and the length of each visit. Check whether the price allows for lifting insulation out of the way and putting it back after the work. Downlights and ceiling fans may need an electrician to disconnect them before the old ceiling comes down. A clear path to the manhole, the hatch into the roof space, and somewhere to stack old plaster and laths, also saves labour time.

Approach What It Involves Estimated Price When It Suits
Re-fixing Screws pull the plaster back up to the laths $45 - $75 per m² Sag with sound plaster
Patching on laths Broken areas cut out and replastered $100 - $200 per m² Local damage in a period ceiling
Emergency stabilisation Props or temporary fixings $300 - $600 Sudden drop or bulge
Section replacement Damaged area replaced with new board $65 - $100 per m² Large damaged area in a plain ceiling
Full ceiling restoration Ceiling repaired with cornice and rose kept $3,000 - $10,000 per room Significant period interiors
Full ceiling replacement Old ceiling removed and new board fitted $55 - $90 per m² Ceiling beyond repair

Salt Damp Behind Flaking Plaster on Old Walls

Salt damp is the name South Australians give to moisture rising through a stone or brick wall and carrying salts that form crystals as the wall dries. The technical note describes the signs as a white powdery deposit on the wall and bubbling or powdering of the plaster, usually low on the wall. Plastering over the damage without dealing with the moisture simply gives the salts a fresh surface to destroy. Most older walls were built with a damp proof course, a barrier layer near the base of the wall, often a tar and sand course that shows as a dark line. The repair plan should start with why that barrier is no longer working. Chemical injection methods and full treatment prices are set out in our salt damp treatment guide.

A fact sheet from the City of Norwood Payneham and St Peters warns against a plinth, a strip of strong cement render at the base of an old wall, since it only traps moisture inside. It also advises against painting old masonry, and suggests keeping at least 100 millimetres of wall exposed below the original damp course. One approach it describes is a sacrificial render, a very weak lime coat that draws salts out of the wall and is then thrown away and replaced. Salt damp work is often split between a damp specialist and the plasterer, with a chemical damp proof course, a water-repelling liquid injected into the wall, costing about $120 to $250 per lineal metre. Paving and garden beds built up against the wall can undo the work, so outside levels matter as much as the plaster, as our guide to hiring a concreter in Adelaide explains.

Before Replastering a Damp Wall

What is involved
Find the original damp proof course and check whether soil or paving now sits above it.
Look for leaking downpipes, drains or garden watering systems near the wall.
Ask how far above the visible damage the old plaster will be removed, and why.
Ask whether a sacrificial render stage is planned before the final coat.
Replastering a salt damp wall before the cause is fixed can mean paying for the same repair twice.

Cracks That Come Back on Adelaide's Reactive Clay

Much of Adelaide sits on reactive clay that swells when wet and shrinks when dry, and the technical note mentions footings, the concrete base under the walls, developed to cope with that movement. When footings move, cracks tend to open at the corners of doors and windows, along cornices and where walls meet ceilings. Many of these cracks open in summer and partly close again in winter, so a crack filled in one season may return in the next. The note warns against the temptation to fill and paint over cracks as soon as they appear, and asks owners to find the cause first.

Ask the plasterer whether a crack looks cosmetic or whether it points to movement in the building. Wide cracks, cracks wider at one end, or doors that suddenly stick should be checked by a building inspector or structural engineer before anyone patches them. Leaking pipes and stormwater pooling against the house can make clay movement worse, and a plumber may need to fix those first. Flexible fillers are useful where small seasonal movement is expected. Selleys makes Spakfilla wall filler and No More Gaps gap filler, which are common choices for small cracks around cornices and trims.

Timing can matter as much as method when cracks follow the seasons. Some owners watch a crack through a full summer and winter before deciding on a repair, so they can see how far it moves. If a crack is still moving, a flexible sealant at the cornice joint may outlast a rigid plaster patch. Ask the plasterer which approach they recommend for each crack and how long they expect it to last. Write the answer on the quote, so a crack that reopens early can be raised with the business.

Telling a Cosmetic Crack From a Warning Sign

What is involved
Hairline cracks at cornice joints often follow seasonal movement and suit a flexible filler.
Cracks wider than a few millimetres, or wider at one end, need a structural check first.
Doors and windows that start to stick point to movement in the frame or footings.
Damp patches near a crack suggest a leak that has to be fixed before patching.
Photograph each crack with a ruler beside it and date the photo, so any movement can be tracked over a season.

State Heritage Places, Local Listings and Interior Plaster

Listed heritage homes are common in the inner suburbs, and the listing can decide whether plaster work needs approval. A State Heritage Place, one on the state heritage register, has the tightest control, and the state guide to developing such places lists plaster, masonry, salt damp, damp course and crack repairs as needing approval. The same guide includes interior work that affects original building materials, and even changes to interior colour schemes. Routine maintenance that involves no repair or replacement does not count as development needing approval. Local Heritage Places, homes listed by the council rather than the state, are handled by the local council, so ask the council before original plaster inside a locally listed home is removed. The PlanSA portal hosts the Planning and Design Code, where each heritage listing appears as an overlay, a mapped layer of extra planning rules.

In the city itself, the City of Adelaide notes that internal fit-out, meaning new fittings and finishes inside, or building works may need planning consent where they affect a heritage place. Council suggests checking each job through PlanSA or by contacting its development assessment team before work starts. It also holds technical specifications on request, including salt damp management, damp proof injection and masonry conservation, for use in a development application. Council's heritage incentives can cover part of the cost of conservation work, and how that scheme works is outlined in our guide to hiring a painter in Adelaide. A free first meeting with the heritage team can be arranged through the City of Adelaide website.

State heritage guidance and grant information are published by the state environment department. Restoring ornate original plaster is specialist work, and prices for roses, panels and period ceilings are set out in our heritage plaster restoration guide. A heritage assessment report costs about $400 to $800 by our estimate, and it can support both the approval and the quotes. Keep any approval with the job records, because a future buyer or their conveyancer, who handles the legal side of a sale, may ask for it.

Listing Plaster Work Inside Who to Ask First Note
State Heritage Place Plaster, salt damp and crack repair listed as needing approval Council and the state heritage unit Interior colour changes are included
Local Heritage Place Check before removing original plaster Local council Internal works can need consent in the city
Historic or Character Area Overlay protects the look of the street Local council Ask whether interior work is affected
Unlisted home No heritage approval for interior plaster CBS for licensing questions Building work rules still apply

Cornices, Ceiling Roses and Matching Old Profiles

A cornice is the moulding that covers the joint between wall and ceiling, and in older Adelaide homes it can be the most expensive part of a room to replace. Plain gypsum cove cornice, the simple curved profile in most newer homes, costs about $8 to $22 per lineal metre fitted by our estimate. Decorative gypsum cornices of 125 to 150 millimetres cost about $20 to $45, and plaster heritage replicas run at $40 to $120. A cornice run by hand in wet plaster to match an original shape can cost $150 to $400 per lineal metre. Prices for each profile and fitting method are compared in our cornice installation guide.

Matching a profile starts with a sample, often a short length cut from a hidden spot or a section that is already damaged. Creating a new profile mould costs roughly $300 to $800, and that cost is spread across every metre run from it. Ceiling roses, the round mouldings at the centre of a ceiling, cost $180 to $400 supplied and fitted for a standard design, while restoring an original one runs at $400 to $1,200. CSR makes Gyprock plasterboard and a range of gypsum cornices, from plain cove to ornamental profiles, which suit rooms where an exact match is not needed. Panels, arches and other decorative work are covered in our ornate plastering guide.

Item Estimated Price How It Is Charged Suits
Gypsum cove, 55 mm $8 - $14 per lm Per lineal metre Newer homes and extensions
Gypsum cove, 90 to 100 mm $12 - $22 per lm Per lineal metre Larger rooms
Decorative gypsum, 125 to 150 mm $20 - $45 per lm Per lineal metre Later period homes
Polystyrene heritage replica $15 - $40 per lm Per lineal metre A period look on a budget
Plaster heritage replica $40 - $120 per lm Per lineal metre Villas with stock profiles
Hand-run plaster $150 - $400 per lm Per lineal metre Exact match in listed homes
Standard ceiling rose $180 - $400 Supply and fit Plain or reproduction rooms
Original rose restored $400 - $1,200 Per rose Period ceilings

Choosing Board for Wet Areas, Ceilings and Fire Resistance

Plasterboard comes in several types, and the right sheet depends on the room and the building rules. Standard board suits dry walls, moisture resistant board is made for wet areas such as bathrooms and laundries, and fire rated board is used where fire resistance is required. Acoustic board has a denser core that can reduce noise between bedrooms and living areas, and costs about $70 to $110 per square metre. Rondo makes steel wall and ceiling framing, along with plaster beads, thin edge strips that give a clean line on corners and curves. Cemintel makes fibre cement internal linings and ceiling sheets. Ask the plasterer to name the board and its thickness on the quote, since cheaper sheets look the same once painted.

Walls behind tiles in a wet area need a waterproofing membrane, and that step is usually done by a tiler or waterproofer rather than the plasterer. Membrane rules and the floor slope to the drain are set out in our guide to hiring a tiler in Adelaide, and board choice is compared in our wet area plastering guide. James Hardie makes fibre cement linings, including Hardie Groove Lining for kitchens, laundries and bathrooms outside the shower. Ardex makes waterproofing membranes and patching compounds used in wet areas. Bostik makes Dampfix waterproofing membranes for use under tiles. Sika makes sheet and liquid applied waterproofing membranes as well as renders.

Square set ceilings, where the ceiling meets the wall in a crisp corner with no cornice, need straighter framing and more finishing time than cornice work. Expect a higher price for square set rooms, and ask how the plasterer will deal with any cracking along that joint. Shadow line details, a small recessed gap at the ceiling edge, are another modern option that suits extensions. They also depend on careful framing, so raise them with the builder before the frame goes up.

Board Typical Use Estimated Price Ask About
Standard board Dry walls $45 - $70 per m² Thickness and stud spacing
Ceiling board Ceilings $55 - $85 per m² Batten spacing and sag resistance
Moisture resistant Bathrooms and laundries $55 - $80 per m² Who installs the membrane
Fire rated Where fire resistance is required $65 - $100 per m² The tested system being followed
Acoustic Bedrooms and media rooms $70 - $110 per m² Insulation in the wall cavity

Asbestos and Silica Dust When Old Linings Come Out

Homes built before the mid-1980s can contain asbestos cement sheeting, and the state's asbestos advice asks for extra care when working on them. Painted flat sheeting in eaves and older additions can be hard to tell apart from other linings by eye. A sample tested by a laboratory is the only reliable answer, and collection plus analysis of one to three samples costs about $200 to $450 by our estimate. Builders and tradespeople must not remove more than 10 square metres of non-friable asbestos, the bonded kind set in cement, without a licence. Larger areas need a removalist with a Class B licence, which covers bonded asbestos, and friable asbestos, which crumbles easily and releases fibres, needs a Class A licensed removalist. Licence types are explained on the SafeWork SA website.

Testing should come before the plasterer cuts, drills or sands anything that might contain asbestos, and sampling is explained in our asbestos testing guide. The state advice is to avoid power tools, abrasive discs and sanding on asbestos cement altogether. Silica dust is a separate hazard, since SafeWork SA treats any material with at least one per cent crystalline silica as a crystalline silica substance, whose fine dust can scar the lungs. That includes mortar, cement products and fibre cement sheeting, so cutting or grinding old render can produce it. Since 1 September 2024, high risk work with these materials needs a silica risk control plan, a written dust control plan, which a safe work method statement (SWMS) for risky building tasks can satisfy.

Fine gypsum dust from sanding new joints is less dangerous, but it spreads through a house quickly. Festool makes M Class dust extractors, rated for fine hazardous dust, which capture it when connected to sanding and cutting tools. Ask how the plasterer will seal off doorways, cover floors and clean up at the end of each day. Vacuuming with a suitable filter traps more dust than sweeping, which simply lifts it back into the air.

Dust and Fibre Checks Before Old Plaster Comes Off

What is involved
Ask whether any sheeting to be removed has been tested for asbestos.
Confirm who will remove any asbestos and which licence class they hold.
Ask how dust from sanding and cutting will be captured at the tool.
Ask for the silica risk control plan or safe work method statement on high risk jobs.
Keep children and pets out of the work area until the dust has been cleaned up properly.

Painters, Electricians and Waterproofers Around a Plastering Job

Plastering rarely happens on its own, and the order of trades affects both the finish and the price. Electricians usually move or add power points and lights before new board goes up, as described in our guide to hiring an electrician in Adelaide. Insulation is easiest to add while a ceiling or wall is open, so ask whether it is included or needs another trade. Painters follow once the final coat has dried, and the first sealer coat shows up any flaws in the plastering. Older paint layers on walls being patched may contain lead, so testing and safe preparation are covered in our guide to hiring a painter in Adelaide.

A plumber is needed if pipes are moved in walls being relined, and the plumbing should be finished and tested before the board closes it in. Dulux makes Acratex render and texture coatings, which can be used on feature walls and older textured surfaces. Ask who books and pays each trade, and who is responsible if one trade damages another's work. Patched walls often need a second visit after the electrician has cut in new outlets, so allow for it in the timing.

Wet area work brings the most trades together, since the plasterer, plumber, waterproofer and tiler all work in the same small room. Ask who checks that each layer is finished before the next trade covers it. A missed step, such as a membrane laid over unprepared board, can stay hidden behind tiles for years. Clear handover points between trades make any later dispute much easier to sort out.

A Sensible Order Around Plastering

What is involved
Roof leaks, plumbing faults and damp problems are fixed first.
Electrical cabling, plumbing and insulation go in while walls and ceilings are open.
Sheeting, setting and cornice follow, with drying time between coats.
Painting comes last, once the plasterer has signed off the final coat.
Agree in writing who patches holes made by other trades after the plasterer has finished.

Putting Right Cracked or Failed Plasterwork

Faults in new plastering often show up within weeks, as joints crack, screw heads show through or patches appear under the paint. Raise each problem with the business in writing, with photos, the quote and the date you first noticed it. Statutory warranties under the Building Work Contractors Act let owners claim for defective domestic building work for five years after it was finished, and that period cannot be extended. Consumer and Business Services can help with advice and conciliation, a meeting that aims to settle the dispute without a court. Claims that cannot be settled can go to the Magistrates Court or District Court, depending on the amount, and the Law Handbook explains the process in plain English.

Some faults point to a problem outside the plasterer's work. Cracks that return after a repair may come from footing movement, a roof leak or salt damp rather than poor workmanship. A plasterer who repairs the same crack twice without asking about the cause may be treating the symptom. Keep records of each repair, since a pattern of returning cracks helps a building inspector or engineer find the cause. Prices for repairing water damage and corner beads are listed in our plaster repairs guide.

What to Look Out For in an Adelaide Plastering Quote

Start with what each quote leaves out, since the lowest total can hide missing work. A patch quote should state the number of patches, the number of visits and whether sanding and a sealer coat are included. Sheeting quotes should name the board type and thickness, the cornice profile, the number of coats and how smooth the final surface will be. For older homes, the quote should say whether lime or gypsum products will be used on masonry walls, and why. Waste removal, protection of floors and furniture, and cleaning up dust each belong on their own line. Check whether moving furniture is included or left to you.

Some warning signs should make you stop and check before signing. A quote to replaster a damp wall that says nothing about the cause of the damp is likely to fail. Plans to fix new board under a sagging lath and plaster ceiling should come with advice on the joists, given the state's warning about extra weight. Missing licence numbers, or a request for more than $1,000 before a job under $20,000 starts, are both reasons not to sign. Plans to cut or sand old sheeting with no mention of asbestos testing put everyone in the house at risk.

Items Every Adelaide Plastering Quote Should Show

What is involved
Board type, thickness, cornice profile and number of coats named in writing.
Lime or gypsum products specified for any work on old masonry walls.
The number of visits included and the drying time allowed between coats.
Protection, dust control, cleaning and waste removal shown on separate lines.
The licence number of the business, matching the CBS register.
Asbestos test results, or a note that no suspect material is affected.

Damp walls priced for replastering with no cause identified.

Requests for more than $1,000 up front on work under $20,000.

An Adelaide plastering quote far below the others may leave out coats, drying visits, waste or the cause of a crack.

Getting Like-for-Like Plastering Quotes Across Adelaide

Each plasterer needs the same description of the job for their quotes to be comparable. List each room, its rough size, the ceiling height and what needs doing, from patches to full replacement. Add photos of every crack, stain and sag, taken with a ruler or tape measure in the frame for scale. Mention the age of the house, whether the walls are stone, brick or timber frame, and any heritage listing you know of. Note any asbestos test results and whether the roof has been checked for leaks.

Three quotes give a useful spread of prices for most plastering work. Ask how long each price holds, when the plasterer can start and how many days the house will be affected by dust. For heritage homes, ask whether the plasterer has worked with lime before and can describe a recent job on a similar house. Staged prices, room by room, make it easier to delay part of the work if the budget runs short.

Keep the quote, contract, receipts and any approvals together once the work is finished. Ask the plasterer to note the products used, including the board, cornice profile and any lime or render mix. Those records make later repairs much easier to match, especially in older homes with several kinds of wall. Paint the new work only after the plasterer confirms it is dry, since moisture trapped under paint can cause bubbling. Cracked render on the outside of the house is a separate job, priced in our render repair guide.

Plasterers Across Adelaide

Plastering prices on this page apply across Adelaide. Jobs close to the main centres rarely carry a travel charge, while outer suburbs and fringe areas sometimes do, especially for small repairs that need several visits.

▶ Inner Adelaide & CBD 10 areas
Adelaide CBD North Adelaide Prospect Walkerville Medindie Kent Town Unley Parkside Hyde Park Thebarton
▶ Eastern Suburbs 10 areas
Norwood Kensington Burnside Glenside Magill Campbelltown Payneham St Peters Rostrevor Athelstone
▶ Southern Suburbs 10 areas
Mitcham Goodwood Blackwood Marion Happy Valley Morphett Vale Noarlunga Centre Hallett Cove Seaford Aldinga Beach
▶ Western Suburbs & Beaches 10 areas
Glenelg Brighton Plympton Henley Beach Grange Findon Woodville West Lakes Port Adelaide Semaphore
▶ Northern Suburbs 10 areas
Enfield Para Hills Modbury Tea Tree Gully Golden Grove Mawson Lakes Salisbury Paralowie Elizabeth Munno Para

Adelaide Plasterer FAQ

Does a plasterer subcontracting to my builder need a licence of their own?
Yes, a plasterer who subcontracts to a licensed builder needs their own building work contractor licence. Consumer and Business Services says employees of a licensed business do not need one. The licence conditions should cover the plastering work being done. You can check the register on the Consumer and Business Services website.
Can gypsum compound or cement render go on the inside of an old stone villa?
The state technical note on older buildings recommends a lime-based render and set coat for repairs to old masonry walls. Cement renders and hard plasters are stronger but more brittle, and the note treats their use with caution. Lime can flex slightly as walls move on clay. Ask the plasterer to explain the product choice in writing.
Should a sagging lath and plaster ceiling be screwed back up or replaced?
Many sagging lath and plaster ceilings can be re-fixed with screws, which costs about $45 to $75 per square metre by our estimate. Broken areas can be patched on new or existing laths at roughly $100 to $200 per square metre. Replacement suits a ceiling that is beyond repair. Keeping the original ceiling also keeps the cornice and rose.
Is it safe to fix new plasterboard under an old ceiling?
The state technical note advises against fixing a new plasterboard ceiling under a damaged old one. The added weight of both layers can overload the ceiling joists. A plasterer should check the joists and the old ceiling before suggesting it. Removing or repairing the old ceiling is usually the safer path.
Why is the plaster bubbling and powdering low on my bluestone walls?
A white powder and bubbling plaster near the base of an old wall are classic signs of salt damp. Moisture rising through the wall carries salts that crystallise as the surface dries. The cause, such as a failed damp proof course or soil above it, needs fixing before replastering. Otherwise the new plaster will usually fail in the same way.
Do I need approval to replaster inside a State Heritage Place?
The state guide to developing State Heritage Places lists plaster repair, salt damp repair and crack repair as work needing approval. Interior work that affects original building materials is included too. Routine maintenance with no repair or replacement does not need approval. Check with your council and the state heritage unit before work starts.
Can a damaged period cornice be matched instead of replaced?
Most period cornices can be matched by taking a sample from a hidden or already damaged section. Making a new profile mould costs roughly $300 to $800 by our estimate. A cornice run by hand from that mould costs about $150 to $400 per lineal metre. Stock plaster replicas at $40 to $120 suit rooms where an exact match is not needed.
Could the sheeting in my 1960s Adelaide home contain asbestos?
Homes built before the mid-1980s can contain asbestos cement sheeting, so a laboratory test is the safe first step. Collection and analysis of one to three samples costs about $200 to $450 by our estimate. Tradespeople may not remove more than 10 square metres of non-friable asbestos without a licence. Friable asbestos always needs a Class A licensed removalist.
What can a plasterer ask for up front on a large renovation?
On domestic building work worth more than $20,000, the deposit is limited to 5 per cent of the contract price. Smaller jobs carry a deposit limit of $1,000. Later payments should be progress payments for work done, requested in writing. Contracts over $20,000 must also be in writing and include Form 1.
How long do I have to claim for faulty plastering work?
Statutory warranties let owners claim for defective domestic building work for five years after the work is finished. That time limit cannot be extended, so raise problems early and in writing. Consumer and Business Services can help with conciliation if the business will not fix the fault. Unresolved claims go to the Magistrates Court or the District Court.

Adelaide Plastering Specialists

For Trades & Contractors - SA

Plastering in Adelaide often relies on other trades for the parts a plasterer cannot do. New power points and lights need a licensed electrician, wet area membranes usually go to a tiler or waterproofer, and asbestos sheeting needs testing and, above 10 square metres, a licensed removalist. These services can be booked alongside a plastering job across the metropolitan area.

Compare Adelaide Plastering Quotes

Tell us your suburb, the rooms involved, what the walls and ceilings are made of and what needs fixing, and compare quotes from local Adelaide plasterers all pricing the same job.

Get Free Plastering Quotes

About This Guide

This page provides guidance information only. Details may change, always verify with the relevant authorities and seek independent professional advice where needed.

Reviewed by The Quote Yard Editorial Team

Published 20 November 2026 ·

How The Quote Yard Works

We connect you with independent local tradies and service providers, we don't perform any trade work ourselves. Tradies provide their own quotes directly to you. Always confirm licensing, insurance, and scope of work before engaging any provider.

All SA tradies are required to hold appropriate licences. Verify at Consumer and Business Services SA.
Prices are 2027 estimates based on typical Adelaide plastering rates. Your final price will depend on the age of the walls and ceilings, the access and the products chosen, so compare written quotes that list labour, materials, visits and waste removal separately.
Need work done? Get free quotes. Post a Job – It's Free