Choosing New Taps or Mixers?

Tell us which taps you want fitted and where, and we'll connect you with licensed plumbers near you.

Get Free Plumber Quotes

Typical Costs (2027 Estimates)

Basin tap or mixer swap (labour)$100-$220
Kitchen mixer swap (labour)$150-$300
Wall-mounted basin mixer (labour)$250-$400
Laundry taps, pair (labour)$120-$250
Garden tap installed$180-$400
Boiling or filtered tap (labour)$400-$900
Call-out fee (business hours)$80-$150

These are 2027 estimates for NSW, and the tapware itself, benchtop drilling, new pipe runs and after-hours visits are extra.

Tap and Mixer Installation Services NSW - Get Local Quotes

Tap and mixer installation in NSW covers fitting new taps to basins, kitchen sinks, laundry tubs, baths, showers and outside walls. A mixer is a tap that blends hot and cold water through one spout, controlled by a single lever or twin handles. The right choice depends on the number of holes in the basin or bench, whether the tap mounts on the bench or the wall, and the water pressure at your home. Building Commission NSW requires a licence for any plumbing work regardless of the cost, so even a simple tap swap needs a licensed plumber. New tapware must carry WaterMark certification, and its Water Efficiency Labelling and Standards (WELS) label shows how much water it uses each minute. Landlords who pass water usage charges on to tenants also need kitchen and basin taps that meet a set flow limit. Homeowners, renovators and landlords should confirm that each tap suits the fixture, the supply pipes and the household before anything is ordered. This guide also covers boiling and filtered water taps, garden taps and backflow protection, and what happens on installation day. Prices are 2027 estimates for NSW, drawn from the price ranges used across our plumbing guides, with separate figures for labour and for tapware. Laundry and bath taps have their own sections, since each uses different fittings. Clear photos of the basin, bench and cupboard below help each plumber give an accurate quote. Post your job on The Quote Yard to compare quotes from licensed local plumbers for new taps and mixers.

Tap and Mixer Installers Across NSW

Licensed plumbers fit basin mixers, kitchen pull-out taps, wall-mounted bath sets, laundry taps, garden taps and boiling water units in homes across Greater Sydney, the Hunter, the Central Coast, the Illawarra and regional NSW. Describe the taps and the rooms, and we can put you in touch with up to three local plumbers for quotes you can compare.

Get Free Quotes

At a Glance - Tap and Mixer Installation in NSW (2027 Estimates)

Job 2027 Estimate (NSW) Main Price Factor Licensed Plumber Certificate of Compliance
Basin tap or mixer swap, existing holes (labour) $100-$220 Access under the vanity Required Yes
Kitchen mixer swap (labour) $150-$300 Pull-out hose and cupboard space Required Yes
Wall-mounted basin mixer (labour) $250-$400 Pipe work inside the wall Required Yes
Laundry taps, pair (labour) $120-$250 Wall or tub mounting Required Yes
Exposed shower mixer (labour) $150-$250 Existing outlet positions Required Yes
Concealed shower mixer (labour) $280-$450 Wall opening and tiling Required Yes
Garden tap, basic (installed) $180-$400 Distance from the nearest pipe Required Yes
Boiling or filtered tap (labour, Sydney) $400-$900 Under-sink unit and power point Required (plus electrician for power) Yes
Tap or mixer supplied and installed (each) $150-$600 Tapware chosen Required Yes
Flow restrictor fitted to an existing tap Quoted per job Tap model Required Yes

Cost Depth: Labour, Tapware and the Extras

Labour to swap a basin tap or mixer onto existing holes is estimated at $100 to $220 for 2027, while a kitchen mixer swap is estimated at $150 to $300. The tapware is a separate cost, from about $50 for a basic tap to $1,500 or more for premium designs. Standard kitchen mixers are estimated at $150 to $600 to buy, and pull-out spray mixers at $300 to $800.

Extra costs come in when the new tap does not match the old one. Core drilling a stone benchtop is estimated at $50 to $150 per hole for 2027, isolation valves at $60 to $150 per pair, and new flexible hoses at $30 to $60 per pair. A brand new tap position, with new pipes run to it, is estimated at $400 to $1,200.

Every job on this table is plumbing work, which needs a licence in NSW whatever its value, and each ends with a Certificate of Compliance, the plumber's signed record that the work complies. Prices are 2027 estimates and exclude tapware unless stated.

What a Tap and Mixer Installation Job Includes

A tap installation job replaces an old tap with a new one, or fits a tap where none existed before. Swapping onto the same holes and pipe positions is the simplest version, since the supply pipes and isolation valves, the small shut-off valves under the bench, are already in place. Fitting a new position, such as a second basin or a garden tap on a far wall, needs new pipe work run to the spot. The plumber also removes the old tap, connects the new one, tests for leaks and checks the hot and cold sides are the right way round.

Fixing a tap that already exists is a different job, priced around worn washers and cartridges, the parts that seal the flow inside a tap. For dripping or stiff taps, book leaking tap repairs in NSW or wider bathroom and kitchen fixture repairs first. Repair can make sense when the tap body is sound and parts are still made. Replacement suits a tap that is cracked, pitted or no longer supported by its maker, or a room that is being updated anyway. Having several taps installed in one visit spreads the call-out fee, the charge for attending, across every fitting.

Tap Styles for Basins, Sinks, Baths and Laundries

Pillar taps are separate hot and cold taps, each sitting in its own hole beside the basin or sink. A three piece set has two handles and a central spout, using three holes in the bench or wall. Single lever mixers control flow and temperature with one handle, and need only one hole. Abey makes bathroom three piece tapware alongside floor mounted bath fillers, which stand beside a freestanding bath. Sussex Taps makes collections such as Voda, Scala and Circa for kitchens, bathrooms, laundries and outdoor areas, and says it has made them entirely in Australia since 1997.

Each room needs a different kind of tap, whatever the style. Basins need a spout that clears the bowl edge and does not splash, while kitchen sinks need height for pots and a reach to both bowls. Laundry tubs need a tap that can fill a bucket, and baths need a fast flow to fill the tub in reasonable time. Brodware makes ranges such as Yokato, Manhattan and City Plus for kitchens, bathrooms and laundries, and carries the Australian Made logo. Matching one range across several rooms keeps finishes consistent, though each tap still has to fit its own fixture. Note the room and fixture beside each tap on the job request, so the plumber can check each one.

Hob-Mounted or Wall-Mounted: Where the Tap Sits

Hob-mounted taps sit on the benchtop or on the basin itself, with their pipes running down into the cupboard below. Wall-mounted taps come out of the wall above the basin, bath or sink, with their pipes hidden inside the wall. Hob mounting is the easier swap, since the plumber works from the cupboard and the wall stays untouched. Wall mounting frees up bench space and suits vessel basins, the bowls that sit on top of a vanity. Labour for a wall-mounted basin mixer is estimated at $250 to $400 for 2027, against $100 to $220 for a hob-mounted basin swap.

Changing from hob to wall mounting means opening the wall, moving the pipes and rebuilding the tiled surface. That work is best done during a bathroom update, since the plumber needs access before the waterproofing and tiles go back. Caroma makes the Riviere Wall Basin/Bath Set, a wall-mounted tap set with a 210 mm spout. The spout length must suit the basin, so the water lands in the bowl and not on its rim. For larger layout changes, plan the taps as part of a bathroom renovation in NSW with the other trades.

Counting the Tap Holes Before You Buy

The number of holes in the basin, sink or bench decides which taps fit without extra work. One hole basins take a single lever mixer, and three hole basins take a three piece set or pillar taps with a spout. Fitting a mixer to a three hole basin leaves two empty holes, which need blanking plates, small caps that seal unused holes, or a cover plate from the tap maker. Check the hole diameter as well, since some taps need a larger or smaller hole than the old one.

Adding a hole to a stone or engineered benchtop needs a diamond core drill, a hollow bit that cuts a clean round hole. Core drilling is estimated at $50 to $150 per hole for 2027, separate from the plumbing labour. Ceramic basins are harder to alter, and buying a new basin can cost less than drilling the old one and risking a crack. Photograph the basin or bench from above with a tape measure in shot, and include the photos with the job request. Kitchen sinks with a tap landing, the flat area behind the bowls, may have a pre-punched hole or a pressed disc that can be knocked out.

Spout Height, Reach and Splash Around the Bowl

Spout reach is the distance from the tap body to where the water falls, and spout height is how far the outlet sits above the bowl. Spouts that are too short send water down the back of the basin, while longer ones can splash the bench. High-rise mixers, which have a tall spout, suit vessel basins and deep kitchen sinks, but can splash in a shallow basin. Compare both measurements on the maker's specification sheet with the size and depth of the bowl. Swivel spouts need clearance from windowsills, splashbacks and wall cabinets as they turn.

Kitchen taps also need room to move the handle fully without striking a window or the splashback. Measure from the tap hole to anything behind it, and compare that with how far the handle swings back on the maker's drawing. Some makers publish dimension drawings with each product, showing heights, reaches and clearances in millimetres. Send the drawing link to the plumber with the photos, so fit problems are found before the visit. Wall cabinets above the sink also limit how tall a curved gooseneck or pull-down spout can be. For new sinks and benches, sink prices sit beside tap options in our kitchen sink and tap cost guide.

Water Pressure and the Tap's Working Range

Water pressure is the force pushing water through the pipes, measured in kilopascals (kPa). Each tap is designed to work within a pressure range, which the maker lists on its specification or installation sheet. Galvin Engineering lists a working range of 30 to 500 kPa in the installation instructions for one of its sensor mixers, for example. Taps fitted outside their range may run weakly or fail to mix hot and cold properly. Ask the plumber to measure the pressure at the property if the existing taps already run weakly or bang when closed. Homes fed by a rainwater tank or a gravity supply run at lower pressure, so check the minimum working pressure before choosing a mixer.

Low flow across the whole home comes from a supply issue that a new tap will not fix. That fault needs low water pressure repairs before tapware is chosen. If only the hot taps run weakly, the cause may sit with the water heater or its valves, and a plumber diagnoses hot water pressure issues as a separate job. Makers list a maximum working pressure as well as a minimum, so high readings matter too. Share any pressure readings with the plumber, so the tap chosen suits the supply at your home.

Matching a Mixer to Your Hot Water Supply

Mixers blend hot and cold water, so they work best when both arrive at similar pressure. Galvin Engineering's instructions for the same sensor mixer say it works when one supply is up to ten times the pressure of the other (10:1), and recommend keeping the two within 10% of each other. Homes where the hot supply is much weaker than the cold may need a mixer rated for unequal pressures, or a valve to balance the two sides. Tell the plumber what type of water heater you have and where it is, since that affects which mixers will perform well. If the heater itself needs attention, arrange hot water services before new taps go in.

Under the NSW variation to the Plumbing Code of Australia, hot water used for washing and bathing must come out of each outlet at no more than 50 degrees Celsius in homes. A lower limit of 45 degrees applies in aged care homes, health care patient areas, early childhood centres, the parts of schools children use and disability facilities. These temperature rules apply to every new hot water system and whenever a water heater is replaced, whatever its type or location. Tempering valves and thermostatic mixing valves blend cold into the hot supply to hold that limit, and each is a separate device from the tap. For those valves, book thermostatic mixing valve installation or tempering valve installation. Supply and install for 2027 is estimated at $250 to $450 for a tempering valve and $350 to $600 for a thermostatic mixing valve in Sydney.

Pull-Out, Pull-Down and Gooseneck Kitchen Mixers

A pull-out mixer has a spray head on a hose that draws out of the spout toward you. Pull-down mixers have a tall, arched spout with a spray head that pulls straight down into the sink. Gooseneck mixers have a high curved spout without a hose, which suits filling tall pots. Caroma makes the Riviere Pull Out Sink Mixer, and pull-out spray mixers are estimated at $300 to $800 to buy in NSW for 2027.

Hose mixers need clear space in the cupboard below, since the hose and its counterweight drop down when the head is pulled. Bins, filters and shelves under the sink can block that movement and stop the head from returning. Clear the cupboard before the visit, and point out anything fixed in place that the plumber should work around. Labour for a kitchen mixer swap is estimated at $150 to $300 for 2027, and pull-out models sit toward the upper end when the hose needs routing. For full sink, bench and dishwasher changes, plan the tap with kitchen plumbing in NSW.

Boiling, Chilled and Filtered Water Taps

Boiling and chilled water taps dispense water from a unit fitted in the cupboard under the sink. Zip Water makes the HydroTap range, which delivers boiling, chilled and sparkling water from one tap. InSinkErator makes steaming hot water taps, including the Multitap 4N1, Multitap 3N1 and Hottap models. These units need cupboard space, a water connection and a power point, and the power point is a job for a licensed electrician. Plan the electrical side with power point installation before the plumber arrives. Labour to install a filtered or boiling tap is estimated at $400 to $900 in Sydney for 2027, with the unit itself estimated at $1,200 to $2,500.

Filtered water taps pass cold water through a cartridge before it reaches a separate spout or a dedicated outlet on the mixer. Puretec makes three-way mixer taps with filter kits, and kitchen undersink filters with optional tap and filter kits. Three-way mixers have one spout with separate channels for hot, cold and filtered water. Filter cartridges need replacing on the maker's schedule, so check the cartridge cost and access before you buy. For fridge lines and under-sink filters, see water filter and fridge water line installation.

Choosing Taps During a Kitchen or Bathroom Renovation

In a renovation, the tap is chosen before the benchtop is cut and the walls are closed. Stone benchtops are cut and drilled to a plan, so the fabricator needs the tap hole size and position. Wall-mounted taps need their in-wall bodies, the valve parts hidden inside the wall, fitted before the wall lining goes on, so the brand must be chosen early. Changing the tap after the bench is cut can leave an unused hole or one in the wrong place. Share the tap specification sheet with the benchtop maker and the plumber at the same time. Where the whole room is changing, the tap belongs in the schedule for a kitchen renovation in NSW.

Renovations also bring the chance to add isolation valves, move a tap or fit a filtered water outlet. Rough-in is the stage when pipes are run to their final positions before walls and benches are finished. The rough-in positions must match the chosen taps, so order the tapware before the plumber starts that stage. Delivery delays on imported tapware can hold up the whole job, so confirm stock and delivery dates early. Once the tap holes are set, the benchtop installer can go ahead with kitchen benchtop installation alongside the plumbing.

Laundry Taps and Washing Machine Stops

Laundry taps fill the tub, and washing machine stops supply the two hoses at the back of the machine. Meir makes laundry mixers and taps, along with wall taps and mixers, and its Lavello kitchen sinks. Wall-mounted laundry sets leave the tub edge clear, while a tub-mounted mixer needs a tap hole in the tub itself. Labour for a pair of laundry taps is estimated at $120 to $250 for 2027.

Washing machine stops should turn off fully, since the machine hoses stay under pressure whenever the stops are open. Fit new stops with the laundry taps if the old ones are stiff or leak slowly around the handle shaft. Laundry tubs and taps are exempt from the NSW rental flow limit, so landlords can choose a faster laundry tap. Full laundry updates with new cabinets and a new tub belong with laundry renovation in NSW. For new laundry waste and supply points, book laundry plumbing at the same time.

Bath Fillers and Shower Mixers in a Renovation

Shower mixers and wall bath mixers sit on a body fitted inside the wall, with only the lever and plate showing. Methven makes shower mixers with a diverter and wall bath mixers in ranges such as Glide, Minimalist and Blaze. A diverter is a valve that sends water to either the shower head or the bath spout. Swapping an exposed shower mixer is estimated at $150 to $250 in labour for 2027, while a concealed mixer is estimated at $280 to $450. The in-wall body must be set at the right depth before the wall lining and tiles go on. Record the brand and range of any in-wall body on the invoice, so a matching lever or trim can be found later.

Replacing a concealed body in a tiled wall means removing tiles, which disturbs the waterproofing behind them. The maker of the existing body may still sell a matching trim or lever, which can avoid that work. Check the existing body's brand before you order, and ask the plumber whether a matching trim exists. For new shower layouts, plan mixer positions with walk-in shower installation so the plumbing and tiling run in order. Where grout cracks or loose tiles show around an old mixer, the plumber can quote on shower leak repairs separately.

Lever Taps for Older or Less Mobile Users

Lever handles can be pushed with a wrist or the back of a hand, which helps people with arthritis or a weak grip. Twin-handle taps that need a firm twist can be harder for the same people to use. Brodware lists a DDA compliant range beside its kitchen and bathroom ranges, and Astra Walker also lists DDA compliant bathroom and kitchen products. DDA stands for the Disability Discrimination Act 1992, the federal law behind Australian accessible design standards. Users who move slowly may not pull away quickly from hot water, so check the tempering valve setting when fitting accessible taps.

Tap height and position count as much as the handle. A tap set within easy reach from a seated position suits wheelchair users at a basin or kitchen sink. Mixers with the lever on the side, away from the spout, keep the hand clear of the water stream. Describe the user's needs in the job request, so the plumber can suggest suitable models and positions.

Sensor and Touch-Free Taps at Home

Sensor taps turn the water on when hands move under the spout and off when they move away. They run on batteries or a mains power supply, depending on the model, so check which type before you buy. Mains-powered sensor taps need a power point or a hardwired supply, a cable wired straight into the home's circuits, installed by a licensed electrician. Battery models avoid that wiring, though the batteries need replacing on the maker's schedule. Some sensor taps deliver water at a preset temperature, set by a mixing valve under the bench. Touch-free taps suit kitchens where hands are coated in food or dough during cooking.

Look for an adjustable sensor range and run time, since a long run time wastes water. Sensor taps need the same WaterMark certification and WELS labelling as other taps. Check that spare parts are sold for the sensor and the solenoid valve, the electrically operated valve that opens and closes the water. Hold on to the maker's manual, as resetting a sensor after a battery change can need a set sequence of steps.

Garden and Outdoor Taps and Backflow Protection

A garden tap, also called a hose tap or hose cock, is a tap for a hose, fixed to an outside wall or to a standpipe, an upright pipe rising from the ground. Installing a basic garden tap close to an existing pipe is estimated at $180 to $400 for 2027. Remote taps that need a new pipe run across the yard are estimated at $400 to $800 or more. Holman makes hose fittings and tap timers, including the BX1 Bluetooth Tap Timer, which fits onto a garden tap. Digging for a new underground pipe can strike other buried pipes and cables, so ask the plumber how these will be located first.

Backflow is the unintended flow of water from a possibly polluted source back into the drinking water supply. Hoses left in ponds, chemical sprayers and irrigation systems can draw dirty water back through a garden tap. On low hazard sites, Sydney Water says its 20 mm and 25 mm water meters already have a built-in backflow prevention device. A hose tap vacuum breaker, a small valve on the outlet that lets air in so dirty water cannot be sucked back, is estimated at $60 to $180 for 2027. Where the tap links to irrigation, rainwater or greywater, the used water from showers, basins and laundries, book backflow prevention device installation with the tap work. Sydney Water rates greywater and stormwater as a high hazard, while a rainwater tank on a property with a 20 mm or 25 mm meter needs no extra device.

Isolation Valves and Flexible Hoses on a New Tap

Each fixture can have its own isolation valve, a small shut-off valve in its supply pipe that stops water to that fixture alone. Braided flexible hoses run from a hob-mounted tap down to those valves under the bench. AS/NZS 3500.1, the national water services standard, limits flexible hose assemblies to accessible locations, so they cannot be buried inside a wall or floor. New taps come with their own hoses, and the plumber connects each hose to its own isolation valve.

For 2027, isolation valves are estimated at $60 to $150 per pair, and spare flexible hoses at $30 to $60 per pair. In homes without isolation valves, every tap change means closing the main tap at the meter. Fitting valves during the installation saves time on later work and lets a failed hose be shut off at the cupboard. Request the hose brand and length on the invoice, so a matching replacement can be ordered later. If water has already damaged the cupboard floor, arrange water leak detection to check for hidden damage first.

Confirming a New Tap Is WaterMark Certified

WaterMark is the national certification scheme for plumbing and drainage products, run under the Plumbing Code of Australia. The Australian Building Codes Board states that a product type listed on the WaterMark Schedule of Products must be certified before it can be installed. It also states that a licensed plumber cannot install a listed product that is not WaterMark certified. Each certified product carries the WaterMark trademark, a licence number and the product specification. The same rule applies to tapware bought through online stores.

Search the WaterMark product database by brand, model or licence number before paying for new tapware. If an online listing gives no licence number, ask the seller for it and keep the reply. Returning an uncertified tap is simpler before it is installed than after. Kohler makes the Components Basin Mixer, and models like it from any brand can be checked in the same database. Send the plumber the model details and licence number with the job request, so they can confirm it before the visit.

WELS Stars and Flow Rates for New Tapware

Taps, showers and toilets are rated for water efficiency under the Water Efficiency Labelling and Standards (WELS) scheme. Each WELS label carries a star rating, and a higher number of stars means lower water use. For taps, the label also shows the water use in litres per minute. WELS testing of tapware includes 50,000 on and off cycles, watertightness and water consumption.

Lower flow saves water at basins, where hands are washed under a running tap. Kitchen taps used to fill pots may suit a higher flow, which earns fewer stars on the label. Compare the litres per minute on each label, not only the star count, when choosing between models. Astra Walker makes the Icon Axial tapware collection, and says its products are designed and manufactured in Australia. Have the plumber note the WELS rating of each tap on the invoice for your records.

Before You Order: Five Checks

Count the holes in the basin, sink or bench and measure the gap from the tap hole to the wall or splashback. Check whether the tap is hob-mounted or wall-mounted, and whether its spout reach suits the bowl. Read the working pressure range on the specification sheet.

Search the WaterMark product database for the model and keep the licence number. Note the WELS stars and the litres per minute for rental kitchens and basins, where a 9 litre per minute limit applies for landlords passing on water usage charges.

Send photos, the model number and the product link to the plumber before the visit. Boiling and filtered water units also need cupboard space, and powered units need a power point.

Water Efficiency Rules for Rented Homes

NSW landlords who pass water usage charges on to tenants must meet set water efficiency measures, and the toilet rule in that list has applied since 23 March 2025. Cold water taps and single mixer taps at internal kitchen sinks and bathroom hand basins must have a maximum flow rate of 9 litres per minute. Taps for the bathtub, laundry sink, washing machine, dishwasher and outdoor taps are exempt from that limit. Shower heads must also flow at no more than 9 litres per minute, and toilets need dual flush and at least three WELS stars. The property must have no leaking taps or toilets at the start of the tenancy, or after any of these measures is installed, repaired or upgraded. Landlords who do not pass on water usage charges are not bound by these flow limits.

Landlords can show they comply with a written statement or report from a licensed plumber who has checked the taps, shower heads and toilets. Replacing kitchen and basin taps with lower-flow models during a tap installation visit can meet the tap requirement. Ask the plumber to include the water efficiency check in the same quote, and to list each tap's flow rate. For toilets in the same check, see toilet installation. Landlords managing several repairs can plan them with rental property maintenance.

What Happens on Installation Day

On the day, the plumber shuts off the water at the isolation valves, or at the main tap if no valves are fitted. The old tap is disconnected and removed, and the bench or basin surface is cleaned where the new tap will sit. Galvin Engineering's instructions say pipework should be thoroughly flushed with clean water before a valve is installed, which clears grit that can damage cartridges. The new tap is fitted, tightened from below, and connected through its hoses to the valves. Water is turned back on slowly, and every joint is checked for drips with the tap open and closed.

Hot and cold sides are tested to confirm the lever turns the right way for each. Spout aerators, the small mesh screens at the outlet, may be removed and rinsed after the first flush. Allow time to clear the cupboard and remove items from the bench before the plumber arrives. Keep the tap's box, instructions and warranty card until the plumber has finished and you have registered the product if the maker asks.

Tap and Mixer Installation Price Estimates for 2027

Prices below are 2027 estimates for NSW, taken from the price ranges used across our NSW plumbing guides. Labour figures assume a tap fitted to existing holes and pipes unless the row says otherwise. Tapware is extra, from about $50 for a basic tap up to $1,500 or more for premium designs. Business-hours call-out fees are estimated at $80 to $150, and hourly rates at $90 to $180. For a broader view of plumbing rates, see the plumber pricing guide for NSW.

Tap Job 2027 Estimate (NSW) Notes
Basin tap or mixer swap (labour) $100-$220 Existing holes and valves
Kitchen mixer swap (labour) $150-$300 Pull-out hoses toward the upper end
Kitchen tap swap, existing holes (Sydney) $180-$350 Sydney figure
Wall-mounted basin mixer (labour) $250-$400 Pipes inside the wall
Laundry taps, pair (labour) $120-$250 Wall or tub mounted
Exposed shower mixer (labour) $150-$250 Existing outlets
Concealed shower mixer (labour) $280-$450 Tiling extra
Garden tap, basic (installed) $180-$400 Close to an existing pipe
Remote garden tap $400-$800+ New pipe run
Filtered water tap, basic (installed) $300-$800 Cartridge replacements extra
Boiling or filtered tap (labour, Sydney) $400-$900 Unit $1,200-$2,500
Instant boiling water system (installed) $2,000-$6,000 Unit and labour
Isolation valves (pair) $60-$150 Added when missing
Core drilling a stone benchtop (per hole) $50-$150 New tap holes
Hose tap vacuum breaker $60-$180 Backflow protection at the tap
New tap position $400-$1,200 Fresh pipe runs

Tap and mixer replacement with the plumber supplying a standard tap is estimated at $150 to $600 per tap for 2027. After-hours rates are estimated at $150 to $250 an hour, so book planned tap upgrades in business hours. Minimum charges of about one hour of labour are common, so grouping several taps into one visit makes better use of that time. Rental flow checks and flow restrictors have no published band, so ask for them to be quoted per job.

What Pushes an Installation Price Up or Down

Access under the vanity or sink has a large effect on labour time. A cramped cupboard, a fixed drawer unit or a corroded old tap nut can double the time spent removing the old tap. Changing from pillar taps to a mixer may need blanking plates or a new basin, which adds parts and labour. Wall-mounted taps cost more because the plumber works inside the wall, and tiling or patching follows. Pipe sizes that do not match the new tap's hoses need adaptors, and old galvanised pipe can crack when disturbed. Removing old silicone and mounting nuts from a stone bench takes care, since the surface can chip.

Travel distance and the home's location also change the final price. For 2027, Sydney call-out fees are estimated at $80 to $180, and regional call-out fees at $60 to $120 for business hours. Rural visits can carry travel charges on top, so ask whether travel is included in the call-out fee. Fixed prices for a set list of taps give more certainty than an hourly rate when access is unknown. Ask what happens to the price if a seized valve or a cracked pipe is found during the work.

Supplying Your Own Tap or Letting the Plumber Supply It

Buying the tap yourself lets you choose any brand, finish or style and compare prices directly. Plumbers who supply the tap add a materials margin, estimated at 10% to 30% over the trade price. When the plumber supplies the tap, the plumber is responsible for the product as well as the fitting. If you supply the tap, confirm the model with the plumber before buying, so it suits the holes, pressure and pipes.

Under the Australian Consumer Law, products must be of acceptable quality and fit for the purpose they were sold for. Services must also be provided with due care and skill, as the Australian Competition and Consumer Commission (ACCC) sets out. When a tap you bought fails, you claim for the product from the seller, while a faulty connection is a claim against the plumber. Keep the receipt, the box label and photos of the installed tap in one place. Read the warranty terms for any installation conditions, and keep the plumber's invoice with the receipt.

Delivery timing matters when you supply the tap yourself. Have the tap delivered and unpacked before the visit, so missing parts are found early. Look inside the box for the hoses, mounting hardware and any blanking plates shown in the instructions. If a part is missing, tell the plumber before the day to avoid a wasted call-out fee.

Who Can Legally Fit a Tap in NSW

Building Commission NSW states that a licence is needed for any plumbing, draining or gasfitting work, regardless of the cost. Tap and mixer installation connects to the water supply, so it is plumbing work under that rule. Unlicensed plumbing work breaches the Home Building Act 1989, with fines of $22,000 for an individual or $110,000 for a company. Check a plumber's licence using the NSW Government's online licence check, which shows the licence categories, expiry date and any conditions. For licence questions, Building Commission NSW can be reached by phone on 13 27 00. Plumbers can hold different licence types, such as contractor licences and tradesperson certificates, and the licence check shows which apply.

Electrical work for boiling water units, sensor taps or under-sink appliances needs a licensed electrician. Some plumbers also hold an electrical licence, but ask to see both licences before relying on that. Gasfitting is a separate licence again, and a plumber who holds it can quote on gas heater servicing while on site. Written contracts are required for residential work over $5,000 including goods and services tax (GST), with a deposit capped at 10%. Statutory warranties, the protections set by law, apply to residential building work, covering major defects for six years and other defects for two.

Certificate of Compliance and Other Paperwork

Every plumbing and drainage job in NSW ends with a Certificate of Compliance, which Building Commission NSW requires once the work is complete. The plumber fills it in as the person responsible, then gives a copy to whoever arranged the job. A Notice of Work, the form that tells the regulator before work starts, is not needed for minor works such as replacing tap ware, so a like-for-like swap starts without one. New tap positions that extend the pipe work may need the full notification process, so ask the plumber how the job is classed.

Keep the certificate with the invoice, the WaterMark licence number and the WELS rating of each tap. These records help when selling the home, claiming on a warranty or proving a rental's water efficiency. Having the certificate emailed makes it easy to find later. If a quote leaves the certificate out, ask whether it is included before you accept. Certificates that arrive without the tap models listed can be returned to the plumber for completion.

Older Homes, Asbestos and Hidden Pipe Problems

Asbestos can be present in homes built before the late 1980s, in wall sheeting behind tiles and in kitchens and bathrooms. SafeWork NSW warns that cutting or drilling these materials can release fibres. Wall-mounted tap work and new tap positions can disturb that sheeting, so test before any cutting starts. Asbestos testing is estimated at $50 to $150 per sample for 2027, and asbestos testing and inspection can be booked before the plumber. SafeWork NSW recommends a licensed asbestos professional to assess or remove any amount of asbestos.

Older homes also hide galvanised steel pipes, which corrode inside and can crack when a tap is unscrewed. Replacing a short section of pipe behind the tap while the wall is open may be suggested in the quote. If old pipes keep leaking after a tap change, the problem may be the pipe and not the new tap. For a failed pipe behind a wall, call for burst pipe repairs and turn off the main tap. Have the pipe material noted on the invoice for future reference. When several fixtures drain slowly at once, the fault may lie in the drain, which a drainer handles as sewer line repairs.

Apartments and Strata Buildings

In an apartment, the plumber may need to shut off water to a riser, the upright supply pipe that serves several units. Strata schemes can set rules on working hours, lift use and notice for shut-offs. Check the by-laws and contact the building manager before booking the work. Fixtures inside a lot, the part of the building you own, are yours to replace, while shared pipes and valves can be common property, the parts all owners share.

Plumbers working in strata buildings may need to show insurance details to the building manager. Find out whether the plumber needs access to a plant room, where the building's pumps and equipment sit, or a shared valve cupboard. The best booking time is one when the shut-off will affect the fewest residents. For shared pipe work and riser valves, the owners corporation can arrange strata plumbing services. Keep a copy of any approval from the strata committee with the Certificate of Compliance. Give neighbours written notice of the shut-off time if the by-laws require it.

Getting Comparable Quotes for New Taps

To get quotes you can compare, send the same job description to each plumber. List each tap, the room, the fixture, the mounting style and whether you or the plumber will supply it. Include photos of the old taps, the cupboard below and the tap holes, plus the model number of any new tap. Note whether isolation valves are fitted and whether the hot water heater is gas, electric, solar or a heat pump. Post the job on plumbing services in NSW to reach licensed plumbers in your area.

Each quote should list labour, parts and call-out fees separately. Look for removal of the old taps, new flexible hoses and isolation valves in the price. A fixed price covering the whole list of taps is easier to compare than an hourly estimate. Ask how long the work will take and whether the water will be off for the whole visit.

Plumbers can still build up their totals in different ways. Some plumbers price a group of taps as one job, while others list each tap with its own labour line. Add up each quote's total for the full list of taps before comparing them. Confirm how long each price is valid, since tapware prices and plumber rates can change. Note the earliest start date offered, which matters when the tap is part of a larger renovation schedule. Keep every quote in writing, including any changes agreed by phone or text message.

What to Look Out For in Tap and Mixer Installation Quotes

A quote that does not name the tap model or WaterMark licence number makes it hard to check what will be fitted. Check that the quote shows the plumber's licence number and the business name that matches the licence. Be cautious of a price well below the others that leaves out hoses, valves or the Certificate of Compliance. Plumbers who will not confirm the tap suits your holes and pressure before ordering may leave you with a product that does not fit. Large upfront deposits for small tap jobs are a warning sign, and NSW caps deposits at 10% for contracted residential work.

A good quote states what happens if the old tap nut is seized or a pipe cracks. Check whether the quote includes a test of the hot and cold sides and a leak check after the water is turned on. Confirm who is responsible for patching walls or replacing tiles after wall-mounted work. Some plumbers register the tap's warranty for you, while others leave that task to the owner. If a problem arises after the work, raise it with the plumber in writing and keep copies of every message.

After Installation: Records, Warranties and First Weeks of Use

Run each new tap for a minute in the first days to flush out any remaining grit. Drips on the cupboard floor in the first week can mean a loose joint, so call the plumber back if any appear. Register the product with the maker if the warranty asks for registration. Spare parts that came with the tap, such as cartridge tools and blanking plates, are worth storing with the manual. Check the maker's cleaning instructions before using any product on brushed or coloured finishes. Clean the spout aerator if the flow becomes uneven, following the maker's instructions.

If a new tap drips, runs weakly or will not turn smoothly, contact the plumber who fitted it first. Fitting faults found in the first weeks can be corrected by the installer on a return visit. Find out whether a return visit for a fitting fault carries a call-out fee. For problems that appear later, the tap's warranty and your consumer guarantee rights both apply. Emergencies such as a burst hose need the water shut off first, then an emergency plumber if the leak continues.

Tap and Mixer Installers Across Sydney and Regional NSW

Plumbers across Sydney fit new taps in homes, units and townhouses, and homeowners can compare plumbers in Sydney for tap upgrades. In Newcastle and the Hunter, households can post jobs for plumbers in Newcastle and the Hunter. On the Illawarra coast, homeowners can request quotes from plumbers in the Illawarra. Regional call-out fees are estimated at $60 to $120 for business hours in 2027, with travel charges possible on rural visits. Regional plumbers may need to order your tap brand in, so check stock when booking.

Port Macquarie and Coffs Harbour homeowners can find tap installers among Mid North Coast plumbers. Around Wagga Wagga and Griffith, tap jobs can be posted for Riverina plumbers to quote on. Rural homes that are not connected to the town sewer can ask the same plumber to quote on septic tank services. Group several taps into one visit, since the call-out and travel are charged once. Confirm the tap model, delivery date and plumber's arrival window before the day. Order tapware early and check it on arrival, so a missing part does not hold up the visit.

Tap and Mixer Installers in Every NSW Region

We connect homeowners with licensed plumbers throughout New South Wales for basin mixers, kitchen taps, laundry sets, garden taps and boiling water units. Post your job once and compare quotes from plumbers who work in your area.

▶ Sydney Inner City 18 areas
Sydney CBD Surry Hills Darlinghurst Potts Point Paddington Redfern Newtown Glebe Balmain Pyrmont Ultimo Chippendale Alexandria Waterloo Zetland Erskineville Rozelle Leichhardt
▶ Greater Sydney 25 areas

Western Sydney

Parramatta Penrith Blacktown Mount Druitt Seven Hills Wetherill Park Auburn Fairfield Cabramatta St Marys

South Western Sydney

Liverpool Campbelltown Bankstown Revesby

Northern Sydney

Hornsby Chatswood Epping Macquarie Park Eastwood

The Hills District

Castle Hill Baulkham Hills

Inner West

Ryde Strathfield Burwood

St George

Hurstville Kogarah
▶ Sydney Coastal 23 areas

Northern Beaches

Manly Dee Why Curl Curl Freshwater Brookvale Collaroy Narrabeen Mona Vale Newport Avalon Palm Beach

Eastern Suburbs

Bondi Tamarama Bronte Coogee Maroubra Randwick

Harbour Suburbs

Double Bay Rose Bay Watsons Bay

Sutherland Shire

Cronulla Miranda Sutherland
▶ Hunter & Central Coast 19 areas

Central Coast

Gosford Terrigal Wyong The Entrance Tuggerah Erina Woy Woy

Hunter Valley

Newcastle Maitland Lake Macquarie Charlestown Belmont Raymond Terrace Cessnock Singleton Muswellbrook

Port Stephens

Nelson Bay Salamander Bay Shoal Bay
▶ Illawarra & South Coast 18 areas

Illawarra

Wollongong Shellharbour Kiama Dapto Corrimal Thirroul Gerringong

Shoalhaven

Nowra Berry Ulladulla Huskisson Vincentia

Sapphire Coast

Batemans Bay Moruya Narooma Bega Merimbula Eden
▶ North Coast 19 areas

Mid North Coast

Port Macquarie Forster Taree Kempsey Laurieton

Coffs Coast

Coffs Harbour Bellingen Sawtell Grafton Yamba

Northern Rivers

Byron Bay Tweed Heads Ballina Lismore Bangalow Lennox Head Brunswick Heads Mullumbimby
▶ Blue Mountains & Highlands 17 areas

Blue Mountains

Katoomba Leura Wentworth Falls Blackheath Springwood Hazelbrook Glenbrook Faulconbridge Lawson Blaxland Lithgow

Southern Highlands

Bowral Moss Vale Mittagong Bundanoon Robertson Berrima
▶ Regional NSW 21 areas

Central West

Orange Bathurst Dubbo Mudgee Parkes Forbes Cowra Young

Riverina

Wagga Wagga Albury Griffith Leeton Goulburn Queanbeyan

New England

Tamworth Armidale Inverell Moree Narrabri

Far West

Broken Hill Cobar

Tap and Mixer Installation FAQs

How much does it cost to install a new mixer tap in NSW?
Labour for a basin mixer swap onto existing holes is estimated at $100 to $220 for 2027. A kitchen mixer swap is estimated at $150 to $300 in labour. The tapware is extra, from about $50 for a basic tap to $1,500 or more. With a standard tap supplied by the plumber, replacement is estimated at $150 to $600 per tap.
Can I fit a mixer tap to a basin with three holes?
Yes, but two holes are left empty when a single lever mixer goes in. Those holes need blanking plates or a cover plate from the tap maker. Another option is a three piece set, which uses all three holes. Check the hole diameter as well before ordering the new tap.
Can I swap a basin tap myself in NSW?
No, because Building Commission NSW states that a licence is needed for any plumbing work, regardless of the cost. Replacing a tap connects to the water supply, so it counts as plumbing work. Check the plumber's licence using the NSW Government's online licence check. Call Building Commission NSW on 13 27 00 if you are unsure about a task.
What flow rate do rental kitchen and basin taps need?
Landlords who pass water usage charges on to tenants need kitchen sink and basin taps with a flow of no more than 9 litres per minute. The limit covers cold water taps and single mixer taps, and since 23 March 2025 toilets must also be dual flush with at least three WELS stars. Bath, laundry, washing machine, dishwasher and outdoor taps are exempt. A written statement from a licensed plumber can serve as evidence that the taps comply.
Does a boiling water tap need a power point?
Boiling and chilled water taps run from a unit in the cupboard under the sink. These units need a water connection, cupboard space and a power supply. The power point must be installed by a licensed electrician. Check the maker's installation guide for the cupboard size and power needs before buying.
How do I check whether a tap bought online is WaterMark certified?
Search the WaterMark product database by brand, model or licence number. Certified products are marked with the WaterMark trademark, a licence number and the product specification. If the listing gives no licence number, ask the seller for it before buying. A licensed plumber cannot install a listed product that is not certified.
Will a new mixer fix weak water pressure at my basin?
A new mixer will not fix low pressure that affects the whole home. Check whether other taps are also weak, and whether only the hot side is affected. Weak flow through the whole home is a supply problem that needs diagnosis first. If only one tap is weak, a blocked aerator or an old cartridge may be the cause, and a plumber can check before quoting.
Do outdoor garden taps in NSW need backflow protection?
Backflow is dirty water flowing back into the drinking supply, for example from a hose left in a pond. For low hazard sites, Sydney Water says its 20 mm and 25 mm meters already have a built-in backflow prevention device. A hose tap vacuum breaker, a small valve on the outlet that lets air in so dirty water cannot be sucked back, is estimated at $60 to $180 for 2027. Sydney Water rates greywater as a high hazard, so ask a plumber which device suits any greywater or irrigation link.
Should I buy the tap myself or let the plumber supply it?
Buying it yourself gives a wider choice and lets you compare prices directly. A plumber who supplies the tap adds a margin, estimated at 10% to 30% over trade price. Plumber supply puts responsibility for the product and the fitting with one business. Either way, confirm the model with the plumber before ordering.
How long does a tap installation visit take?
A like-for-like swap onto existing holes and valves is the quickest job. Pull-out kitchen mixers take longer, as the hose and weight need routing in the cupboard. Wall-mounted taps and new positions take longest, since the wall has to be opened and the pipes moved. Ask each plumber for a time estimate in the quote, so you can plan the water shut-off.

More Tap, Valve and Outdoor Water Services

For Trades & Contractors - NSW

Licensed plumbers who fit basin mixers, kitchen taps and outdoor taps can find current work on the NSW job leads board, along with plumber jobs in NSW and bathroom renovation plumber jobs.

Need New Taps or Mixers Fitted in NSW?

Post your job and compare quotes from licensed NSW plumbers for basin mixers, kitchen taps, laundry sets, garden taps and boiling water units.

Get Free Plumber Quotes

About This Guide

This guide is general information only, and NSW rules, product details and prices can change. Confirm requirements with Building Commission NSW, your water authority, the tap maker and a licensed plumber before work starts.

Reviewed by The Quote Yard Editorial Team

Published 17 November 2026 ·

How The Quote Yard Works

We connect you with independent local tradies and service providers, we don't perform any trade work ourselves. Tradies provide their own quotes directly to you. Always confirm licensing, insurance, and scope of work before engaging any provider.

All NSW tradies are required to hold appropriate licences. Verify at NSW Fair Trading.
Prices are 2027 estimates for New South Wales and exclude tapware, benchtop drilling, tiling and electrical work unless stated. Rental flow checks and flow restrictors have no published band and are quoted per job.
Need work done? Get free quotes. Post a Job – It's Free