Need Waste Taken Away?

Tell us what the waste is and where it is stored, and we'll put you in touch with licensed operators near you.

Get Free Waste Quotes

Typical Costs

WA waste levy (metro, from July 2026)$90/tonne
Metro landfill tipping (gate) fee$217-$292/tonne
Septic waste fee at treatment plantAbout $136 per 1,000 L
Grease trap pump-out (up to 1,000 L)From about $280 + GST
Vacuum truck with driver (Perth)$165-$225/hr
Car tyre drop-off (metro)$10-$31 each
Skip bin 4 cubic metres (metro)$330-$550

These are 2027 estimates from published WA fees, and septic pump-outs, portable toilets and clinical waste are priced on quote.

Waste Management Cost WA - Get Local Quotes

Waste management cost in WA depends on what the waste is, how much there is, and where it has to go after it leaves your property. Septic tanks, grease traps, used tyres and contaminated soil are each priced in a different unit, so an hourly rate alone does not show the full cost. Households, strata managers, farms, workshops and building sites are all priced this way, even though their volumes differ. Liquid waste is charged by the litre or kilolitre, which is one thousand litres, while solid waste is weighed at the landfill gate and charged by the tonne. Controlled waste, the legal term for regulated waste such as sewage, grease, waste oil, tyres and clinical waste, must be carried by a licensed operator, and that cost is in the rate. Liquid loads also pay a receival fee, the treatment plant's charge to accept them, so no lawful pump-out can cost less than that fee. In the Perth metropolitan region, the landfill gate fee, or tipping price, includes the state waste levy, a tax on landfill waste set at $90 per tonne from 1 July 2026. Regional sites outside the levy area can charge far less for the same load, but the extra travel can wipe out the saving. The figures below are 2027 estimates built from published WA fee lists, and they show what each line of a quote should cost. Where no reliable published price exists, we say so and explain what drives the price instead of guessing. Use the tables to check the disposal and transport lines on any quote, then compare offers from licensed operators through The Quote Yard.

Waste Management Costs Across Western Australia

Pricing for liquid waste, landfill disposal, tyres, contaminated soil, asbestos, bins and vacuum trucks across Perth, the South West, the Wheatbelt, the Goldfields and the north of the state. Post one job and we can connect you with licensed waste operators across Western Australia, so you can compare up to three written quotes.

Get Free Quotes

At a Glance - WA Waste Disposal and Collection Costs

Type of Waste 2027 Estimate Charged By Controlled Waste
General waste at a metro landfill $217-$292 per tonne Weight in tonnes at the tip No
Septic waste or sewage fee at treatment plant About $136 per kL (1,000 litres) Per 1,000 litres delivered Yes
Grease trap pump-out (Perth) From about $280 + GST Litres the trap holds Yes
Vacuum truck with driver (Perth) $165-$225 per hour Hour, plus disposal Depends on load
Car tyre drop-off (metro) $10-$31 each Per tyre Yes
Contaminated soil up to Class III (metro) About $220 per tonne Tonne, after testing Yes
Asbestos at a metro landfill About $450 per tonne Tonne or small load Yes
Skip bin 4 cubic metres (metro) $330-$550 Bin size and weight No
Septic pump-out, toilet hire, clinical waste Priced on quote Visit, week or bin Yes

What Moves a Waste Management Price in WA

Nearly every waste quote is made up of three costs: the truck and crew time, the trip to an approved facility, and the fee that facility charges to accept the waste. Metro landfill fees include the state levy, and liquid waste is charged per kilolitre, or 1,000 litres, at the treatment plant. Controlled waste, the legal term for regulated waste such as septic waste, grease, oils, tyres and clinical waste, also needs a licensed carrier, which adds to the rate.

Site access, distance from the depot and how quickly you need the job done then move the price up or down within each range. Waste sitting behind the house, on a remote farm or in a spill at night will cost more than the same waste collected from a kerbside on a weekday.

Prices are 2027 estimates for Western Australia based on recent published fees and price lists. Septic pump-outs, portable toilet hire and clinical waste are priced on quote.

How Waste Jobs Are Priced in Western Australia

Waste operators in WA price each type of waste by the unit that matches how it is collected and where it ends up. Liquid waste such as septic sludge, grease trap waste and wash-down water is measured in litres or kilolitres, and one kilolitre equals one thousand litres. Solid waste going to landfill is weighed on a weighbridge, a scale the truck drives over, and charged per tonne, although some smaller regional sites charge per cubic metre instead. Tyres are counted one at a time, portable toilets are hired by the week, and vacuum trucks are billed by the hour. Knowing the unit lets you check whether a quote sits in a sensible range before you look at the total.

Every waste quote is built from the same basic parts, even when the invoice shows a single figure. First comes the labour and truck time needed to reach your site and load the waste. Next is the transport to a facility that is allowed to accept that waste, followed by the disposal or treatment fee that facility charges, called a receival fee for liquid loads. Extras are then added, such as a minimum charge, which is the least you pay however small the job, plus extra hose, after-hours work and paperwork.

Controlled waste adds extra cost that householders do not always expect. In WA, controlled waste means any waste listed in Schedule 1 of the Environmental Protection (Controlled Waste) Regulations 2004, including sewage, grease trap waste, waste oils, tyres, asbestos and clinical waste. Carriers, drivers and vehicles that move controlled waste on a road must be licensed by the Department of Water and Environmental Regulation, known as DWER. Bulk loads carried in a tank also need a tracking form, which is a record that follows the waste from your site to the receiving facility. That licensing, the specialised trucks and the record keeping are all built into the carrier's rate. If you are unsure what type of waste you have or which licence applies, start with our guide to choosing waste management services in WA and then come back for prices.

GST applies to some wastes and not others, which can make two quotes look further apart than they really are. Water Corporation, the state-owned water utility, lists its fees for accepting septic tank waste and sewage as GST free, while grease waste and vehicle wash water attract GST. Council landfill schedules for 2026-27 show their gate fees with GST already included in the published figure. Have every quote show GST as a separate line so that you compare every price on the same basis. Businesses registered for GST can then see how much of the bill they can claim back.

The WA Waste Levy and Landfill Gate Fees

The Waste Avoidance and Resource Recovery Levy is a state charge on waste that ends up in landfill. It applies to waste received at licensed landfills in the Perth metropolitan region, and to waste collected in that region and taken to a licensed landfill outside it. From 1 July 2026 the rate is $90 per tonne, or $136 per cubic metre at landfills that take only inert waste, such as rubble, and charge by volume. Landfill operators pay the levy to the state every three months and recover it through their gate fees, which are the prices charged to tip waste. The current rate and the expected rates for later years are listed in the levy rate schedule on WA.gov.au.

You never receive the levy as a separate bill, but it is built into every tonne of metro waste on your quote. One Perth metro council's 2026-27 commercial schedule charges $217 per tonne for mixed, commercial and building waste, and states that this fee includes the levy. Another metro landfill lists general waste at $291.50 per tonne including GST for the same year. At those rates the levy makes up a large share of the price of each tonne, before a carrier adds transport and labour.

Regional landfills outside the levy area can charge much less for waste generated locally. One Wheatbelt shire lists general waste at $40 per tonne for 2026-27, and remote sites we checked charge about $11 to $81 per cubic metre for commercial loads. Those lower fees are for local waste, not for loads trucked out of Perth to avoid the levy. Waste collected in the metro region still attracts the levy when it is received at a licensed landfill outside the region. Acceptance rules differ from site to site, so confirm that the landfill will take your load, and at what price, before booking a truck.

Landfill Charge 2027 Estimate Notes
WA waste levy (metro landfills) $90 per tonne $136 per cubic metre at rubble sites that charge by volume; $93 per tonne expected from 1 July 2027
General, commercial or building waste (metro gate fee) $217-$292 per tonne Levy and GST included in published council fees
Minimum charge per load (metro) $29-$100 Applies to small loads under the minimum weight
General waste (regional site outside levy area) From about $40 per tonne Some sites charge $11-$81 per cubic metre for commercial loads
Contaminated soil up to Class III (metro) About $220 per tonne $100 minimum; waste approval needed before delivery
Asbestos (metro landfill) About $450 per tonne Small loads up to 100 kg about $45

Septic Tank and Liquid Waste Pump-Out Costs

Pumping out a septic tank removes the septage, meaning the mix of sludge, scum and liquid that builds up inside the tank over time. WA Health says a septic tank needs pumping out at least every four years, or more often if the approval conditions for the system require it. The job is done with a tanker that sucks the contents through a hose into a sealed tank on the truck. Septic waste is controlled waste, so the driver, the vehicle and its tank all need DWER licences. The load must then go to a facility licensed to accept it, and that receival fee is a large part of the price. No reliable published WA price exists for a householder pump-out, so we do not give a band for the service itself.

What we can show is the disposal part of that price, because receival fees are public. For 2026-27 Water Corporation charges $136.21 per kilolitre for septage and sewage delivered by licensed carriers, and both fees are GST free. Council liquid waste ponds in regional WA charge from about $0.07 per litre up to $163 per kilolitre, depending on the shire and where the load comes from. Emptying a tank holding three kilolitres would therefore carry a disposal cost of roughly $410 at the metro treatment plant rate. Truck time, travel and the operator's margin are added on top, and current receival fees are listed on the Water Corporation website.

Several site details push a septic quote up or down. Hose length matters because each truck carries a set length, and a tank far from the driveway may need extra hose and a second worker. Buried or sealed lids that have to be dug out add labour before pumping can start. Tanks that have gone years without service hold thicker sludge, which takes longer to break up and remove.

Aerobic treatment units, known as ATUs, use air pumps and bacteria to treat wastewater to a higher standard before it is irrigated on the property. WA Health requires these systems to be serviced every three months, or on another schedule approved by the Chief Health Officer. Only a person approved by the Chief Health Officer may carry out that servicing. Owners carry the quarterly service charges for the life of the system, plus periodic desludging, which means pumping out the settled solids. There is no published WA fee for a quarterly ATU service, so compare written service agreements from approved service providers, whose list is kept by WA Health.

Grease traps, also called grease arrestors, are tanks that catch fats and oils from commercial kitchens before the wastewater reaches the sewer. One published Perth price list charges about $0.28 per litre of trap capacity plus GST, with a minimum of about $280 plus GST for traps up to 1,000 litres. On that basis a 2,000 litre trap would cost up to about $560 plus GST for each pump-out, before any volume discount. The treatment plant fee for grease waste is $147.18 per kilolitre including GST, which is higher than the rate for septage. Your yearly cost depends on how often the trap is emptied, so request a price for a full year of scheduled services as well as a single visit.

Liquid Waste Item 2027 Estimate Notes
Septic waste or sewage fee (metro treatment plant) About $136 per kL GST free; delivered by a licensed carrier only
Grease waste fee (metro treatment plant) About $147 per kL GST included
Car and truck wash water fee About $62 per kL GST included
Council liquid waste ponds (regional) $0.07 per litre to $163 per kL Higher rates for loads from outside the shire
Grease trap pump-out (Perth) About $0.28 per litre of trap size + GST Minimum about $280 + GST for traps up to 1,000 L
Septic tank pump-out (service) Priced on quote Driven by volume, hose length, lid access and travel
ATU quarterly service Priced on quote Required every 3 months unless the Chief Health Officer approves otherwise
Septic or ATU application to council $118-$236 Per application for a new or altered system

Reading the Disposal Line on a Liquid Waste Quote

Every liquid waste quote should show the volume pumped, the rate per kilolitre or per litre, and where the load will be emptied. If the volume is an estimate, the quote should say how a larger or smaller load will be charged on the day. The receival fee for septage at the metro treatment plant is about $136 per kilolitre, so ask about any disposal line that sits far below that figure.

Grease waste, wash water and septage each carry their own receival rate, so a quote that combines them in one line is harder to check. Listing each type on its own line lets you see whether the operator is charging the right rate for the right waste.

Receival fees change on 1 July, at the start of each financial year. Check the current figure before comparing quotes for a large or recurring job.

Vacuum Truck and Vacuum Loading Rates

Vacuum loading means using a truck-mounted vacuum pump to suck liquids, sludge or loose material through a hose into a sealed tank. It is used for pits, sumps, wash bays, spills and digging safely around buried pipes and cables without a machine bucket. Vacuum trucks in Perth are hired by the hour with an operator, which is known as wet hire. Compiled supplier rates show about $165 per hour for a 1,000 litre unit, and about $170 to $225 plus GST per hour for trucks from 3,000 to 7,000 litres. Larger trucks are priced on request, so confirm whether the hourly rate includes disposal of the load.

Where disposal is charged separately, it follows the receiving facility's rate, which varies with the waste type and any contamination. Wash water from a vehicle wash bay costs much less to dispose of than grease or septage. Check whether the quote counts travel from the depot as billable time and whether there is a minimum hire period. If the problem is a blocked sewer line and not a full pit, a plumber clearing blocked drains may be a cheaper first call than a tanker.

Access has a direct effect on the hours you pay for. Large tankers need firm ground and room to park close to the pit, while a tight site may suit a smaller truck with a longer hose. Narrow laneways, low carports and soft lawns can force the operator to use a smaller unit that needs more trips to the facility. Each extra trip adds travel time, another receival fee and more hours on the invoice. Tell the operator about the access, the pit depth and the expected volume when you request a price. Photos of the driveway and the pit lid help the operator choose the right truck before arriving.

Waste Oil, Oily Water and Hydrocarbon Disposal Costs

Hydrocarbon waste, meaning oil and fuel based waste, covers used engine oil, hydraulic oil, fuel residue and mixtures of oil and water from workshops and wash-down areas. Used mineral oils that can no longer do their job, and oil and water mixtures, are both listed as controlled waste in WA. Householders can drop small amounts of used oil at council transfer stations, where recent council schedules show it free or up to about $2.50 per litre. Commercial drop-off at the council sites we checked costs about $0.30 to $3.50 per litre, and one site caps each drop-off at 20 litres. Those fees are for small containers delivered by the owner, not bulk tanks or drums collected from a business.

Bulk collection of waste oil from a workshop tank or drum store is priced on quote. The price depends on the volume, whether the oil sits in a bulk tank or in drums, and whether water or other liquids are mixed through it. Every bulk load needs a tracking form, and so does any load in drums or containers of 200 kilograms or litres or more. Mixed loads can cost more to accept, because the facility has to deal with each liquid in the mix. Keeping oil apart from coolant, solvents and wash water in labelled drums gives the carrier a cleaner load to price.

Workshops, car washes and fuel sites use oil and water separators, which hold back oil so that cleaner water can flow on to sewer or a holding tank. These units need regular pump-outs, and the waste is charged as oily water or sludge at the receiving facility. Water Corporation lists car and truck wash water at $61.82 per kilolitre including GST for 2026-27. That is less than half the rate for grease or septage, so keeping wash water separate from heavier sludge can cut disposal costs. Your carrier should tell you which waste code, a short label for the type of waste, goes on the tracking form, such as K110 for grease waste, because the receival fee depends on that code.

Used Tyre Disposal Costs

Used tyres are controlled waste in WA, even where a landfill may lawfully accept them. Carriers transporting used tyres on a road need a packaged controlled waste carrier licence, which covers waste carried in containers, even for a small load. A tracking form is needed once a load reaches 200 kilograms, which the state fact sheet puts at about 25 used car tyres. That rule matters for farms, fleets and workshops clearing a backlog, because a large pile cannot simply be carted away by anyone with a ute. Householders dropping off a few tyres at a transfer station pay a per tyre fee instead. Check the site's limit before loading the trailer, because some transfer stations cap the number of tyres per visit.

Recent council fee schedules show a wide spread across the state. Car and motorbike tyres cost about $10 to $31 each at the Perth metro sites we checked, and as little as about $3 at one remote site that charges only to cover its costs. Four-wheel drive and light truck tyres cost about $25 to $30 each, and tyres still on the rim can attract a higher fee. Truck tyres range from about $10.50 to $68 each, and one large metro facility does not accept them at all.

Tractor, loader and mining tyres cost far more to dispose of. One coastal shire in the north of the state charges about $96 for a tractor or large machinery tyre and over $1,300 for a mining haul truck tyre. Those fees cover disposal only, so collection from a farm or mine site adds truck time, travel and loading equipment. Once used tyres are recycled into a new product, that product is no longer treated as controlled waste. The controlled waste rules apply to the tyres themselves whether they are being disposed of or sent for recycling.

Tyre Type 2027 Estimate (Drop-Off) Notes
Car or motorbike tyre $3-$31 each Metro sites about $10-$31; some sites limit numbers per visit
4WD or light truck tyre $25-$30 each Fee rises when left on the rim
Truck tyre $10.50-$68 each Not accepted at some metro facilities
Tractor or large machinery tyre About $96 each Regional site example
Haul truck tyre Over $1,300 each Mining tyres priced individually
Collection from a farm, fleet or site Priced on quote Licensed carrier needed; tracking form at 200 kg or more

Contaminated Soil Testing and Disposal Costs

Contaminated soil is soil holding fuel, chemicals, asbestos fragments or other material above the levels a standard landfill can accept. Soils contaminated with a controlled waste are themselves listed as controlled waste in WA. Landfills assess this soil against the state's Landfill Waste Classification and Waste Definitions 1996, which sets acceptance criteria for each class of landfill. Classification, which decides the class of landfill that can take the soil, relies on lab tests of soil samples. No published WA price list for sampling and lab analysis could be found, so that part of the job is priced on quote. The number of samples, the chemicals tested for and how fast you need results all affect that price.

Disposal fees are easier to estimate once the soil has been classified. One Perth metro council charges about $220 per tonne including GST for contaminated soil accepted at its Class III landfill, with a $100 minimum per load. Class III is one of the state's landfill classes for putrescible waste, meaning waste that rots, and the soil must meet that class's limits. The site requires a waste approval application before the load arrives, so build that lead time into your project. Excavation, loading and trucking are quoted separately from disposal, so compare each line on its own.

Site owners have reporting duties as well as disposal costs. Under the Contaminated Sites Act 2003, an owner, occupier or person who caused the contamination must report a known contaminated site to DWER within 21 days of becoming aware of it. Building and demolition projects that uncover stained or strong-smelling soil should pause and arrange testing before the material leaves the site. Once the soil class is known, an excavation and earthmoving contractor can price the digging and loading alongside the disposal.

Asbestos Disposal and Removal Costs

Asbestos is controlled waste, but the state fact sheet on asbestos says a carrier licence and tracking form are not required to transport it. It must still be wrapped, labelled and taken only to a licensed facility that accepts asbestos, and not every landfill does. Gate fees for 2026-27 range from about $45 for a small load up to 100 kilograms at a metro landfill, to $450 per tonne for larger metro loads. Regional sites charge from about $100 per tonne, or about $105 to $148 per cubic metre. Some regional sites take only small residential quantities and need notice before you arrive.

Removal labour, sealing off the work area and the final safety check are charged on top of the disposal fee. WorkSafe WA requires a Class B licence to remove more than 10 square metres of bonded, or non-friable, asbestos, and a Class A licence for friable asbestos. Friable asbestos is material that is powdery or can be crumbled by hand when dry. Licensed removal of a small bonded area runs from about $400 to $1,200, and an asbestos fence from about $1,500 to $5,000. An asbestos cement roof costs from about $5,000 to $15,000 or more, and friable removal starts at about $3,000. Before paying for removal, book asbestos testing and inspection to confirm the material, then compare quotes for asbestos removal or asbestos roof removal.

Portable Toilet Hire and Servicing Costs

Portable toilets are hired for building sites, farm field days, weddings and community events where there are no permanent toilets. Hire is charged per unit per week or per event, with servicing visits either built into the hire or charged as extra pump-outs. No published WA price list we could rely on was found, so we have not set a band and each job is priced on quote. The waste pumped from a portable toilet is sewage, which is controlled waste, so the service truck and driver need DWER licences. The disposal part of each service follows the sewage receival rate, which the metro treatment plant sets at $136.21 per kilolitre. Delivery distance, the number of units and the servicing schedule have the biggest effect on the total.

Event organisers need to plan for how heavily the toilets will be used, not just the headcount. The Chief Health Officer guideline for temporary toilets says they must be kept sanitary and working, with servicing set by the supplier's advice and the level of use. Local governments regulate temporary toilets at events, so your council may set conditions as part of the event approval. For building sites, the guideline refers builders to the state's codes of practice on construction work and workplace facilities.

Clinical, Sharps and Chemical Waste Costs

Clinical waste from medical centres, dental surgeries, vets, funeral homes and home healthcare providers is controlled waste. The carrier must be licensed, and the waste must be unloaded only at a facility permitted to accept it. Collection quotes depend on bin size, collection frequency and travel distance. We found no published WA price list for clinical bin collection, so there is no band here. Practices comparing quotes should check that the price includes bin supply, liners and a disposal record for each collection.

Households have cheaper options for small amounts of sharps and chemicals. HealthyWA advises keeping used needles and syringes in a rigid, puncture-resistant plastic container with a screw-top lid. The container can then go back to a needle and syringe program, or into a disposal unit provided by some councils and businesses. Never put sharps in a recycling bin or flush them down a toilet. Household paints, solvents, pesticides, small barbecue or camping gas cylinders and household batteries can go to a Household Hazardous Waste Program facility at no charge. The program accepts up to 20 kilograms or 20 litres of each material type, and it takes domestic waste only.

Commercial, farm, laboratory and veterinary chemicals are excluded from the household program and must go through a licensed carrier. Pricing depends on how many products there are, whether they are labelled, and whether unknown containers must be identified before transport. Containers or drums contaminated with residues of a controlled waste are also listed as controlled waste, so empty chemical drums with residue still need a licensed carrier. Make an inventory with product names, volumes and container sizes before you request quotes, because unlabelled items add identification costs. No published WA rate for commercial chemical collection was found, so expect a quote after the operator reviews your list.

General Rubbish, Skip Bins and Commercial Bin Lifts

General rubbish is simpler to price because it goes to a standard landfill or recycling facility without controlled waste paperwork. In metro Perth a 2 cubic metre skip costs about $220 to $380, and a 6 cubic metre bin about $420 to $700. Extra hire days add about $15 to $40 per day, and overweight bins attract about $150 to $400 per tonne. Heavy loads such as soil, concrete and bricks reach the weight limit well before the bin looks full. For bin sizes, verge permits and banned items, see our guide to skip bin hire in WA.

Hiring a crew with a truck can cost less than a skip when the pile is small, or bulky but light. Single items run about $120 to $280, and a small load of one to two cubic metres runs about $240 to $450. Medium loads of three to five cubic metres sit around $420 to $850. You can compare both options on our rubbish removal page, and green waste from land clearing is priced as its own stream.

Businesses with regular general waste pay for bin lifts, which is the charge each time a truck empties a wheelie bin or bulk bin. The price per lift depends on the bin size, how often it is emptied and how much of the contents can be recycled. No per-lift price we could rely on was published for WA commercial collection, so lifts are priced on quote. Strata managers and business owners can compare one large bin against two smaller ones, because fewer lifts can mean a lower yearly bill. Recycling and food or garden waste bins are priced separately, so sorting takes weight out of the general bin that pays the landfill levy.

Bin or Pickup 2027 Estimate Notes
Skip bin 2 cubic metres (metro) $220-$380 Mini skip for small clean-ups
Skip bin 4 cubic metres (metro) $330-$550 Common size for home clean-ups
Skip bin 6 cubic metres (metro) $420-$700 Renovation and clear-out size
Skip bin 8 cubic metres (metro) $520-$850 Weight limits apply
Skip bin 10 cubic metres (metro) $650-$1,000 Large clear-outs and building waste
Extra hire day $15-$40 per day Agree the hire period up front
Overweight surcharge $150-$400 per tonne Heavy materials fill the weight limit first
Single item pickup $120-$280 Couch or mattress
Commercial bin lift Priced on quote Depends on bin size, frequency and recycling split

Travel and Mobilisation Costs in Regional and Remote WA

Distance has a large effect on waste pricing in WA. Liquid waste trucks may need to travel a long way to reach the nearest facility licensed to accept the load. Water Corporation's plants at Bunbury, Busselton, Dunsborough, Margaret River and Bridgetown accept sewage waste only, so grease or oily loads from the South West need another destination. Some shires run their own liquid waste ponds, but they can charge more for loads from outside the shire boundary. One Wheatbelt shire charges $83 per 2,000 litres for septic waste from inside the shire, and $355 for the same volume from outside it. Before booking, confirm where the carrier will empty the load and whether that facility charges a local or out-of-area rate.

Mobilisation is the cost of getting a crew and equipment to a remote site and back again. For mine sites, pastoral stations and remote communities it can include fuel, driver hours, accommodation, meals and the return trip. Safety inductions, medical checks and access permits on mine sites also take paid time before any work begins. We found no published WA mobilisation rates, so these jobs are quoted case by case. Grouping several properties or pump-outs into one trip is a direct way to share that cost.

Regional landfill gate fees can be lower than metro fees, partly because the levy does not apply to waste generated and disposed of outside the metro region. That saving can disappear once travel is added, so compare the total delivered price. If a pump-out reveals a cracked tank or a blocked leach drain, you can find plumbers in the Avon Valley and Wheatbelt or plumbers in Albany and the Great Southern to quote the repair. Leach drains are the buried chambers or pipes that spread treated water into the soil, and repairing one is separate from the pump-out price.

After-Hours Callouts and Emergency Spill Costs

Emergency waste work costs more because a crew and truck must leave other jobs or come out outside normal hours. Overflowing septic tanks, flooded grease traps, fuel spills and burst sewer lines are the typical urgent calls. Expect an after-hours callout fee on top of the hourly or per-litre rate, and confirm the amount by phone before the truck leaves. Receival facilities also keep set hours, and Water Corporation charges $132.62 per hour for a supervisor at weekend special openings in 2026-27. If the problem can safely wait until business hours, booking a daytime visit avoids that surcharge.

Chemical and fuel spills need containment first, then clean-up and disposal of the used absorbent material. Spill kits hold absorbent pads, socks and granules that soak up liquids and stop them reaching drains. Used absorbents must be disposed of according to what they soaked up, so ask the carrier how they will classify the load. Serious spills that threaten people, waterways or property need an emergency response, so call 000 first. Clean-up afterwards is priced on the hours worked, the volume of waste collected and the receival fee. Oil stains left on paving can then be treated by pressure cleaning once the spill itself has been removed.

Service Frequency and Contract Pricing

Regular servicing turns an unpredictable bill into a fixed cost that you can budget for. Commercial kitchens, workshops, strata complexes and farms with ATUs can arrange a schedule of visits at an agreed rate per service. Any contract should set the frequency, the volume included in each visit, the charge if that volume is exceeded and how the price changes each year. Read the part on yearly price rises carefully, because some agreements tie increases to the levy or to facility disposal fees.

The levy itself rises on a published schedule, from $90 per tonne in 2026-27 to an anticipated $93 in 2027-28 and $94 in 2028-29. Contracts that pass on only the actual levy rise are easier to check than ones that allow any increase. Treatment plant receival fees are also published for each financial year, so you can match any increase to the official rate. Keep each year's fee notices with the contract so the figures are easy to compare at renewal. Getting a one-off price for the same service shows you what the contract is saving.

Waste services sold to consumers come with consumer guarantees under the Australian Consumer Law. Services must be supplied with acceptable care and skill, be fit for any purpose you stated, and be supplied within a reasonable time if none was agreed. If a pump-out is done poorly or a bin service keeps missing lifts, those guarantees give you a basis to ask for the problem to be fixed. You can read the full guarantees on the ACCC website before raising a complaint. Keep the quote, the invoice and any tracking form receipt, because together they show what was agreed and what was delivered. Waste holders, meaning whoever hands the waste over, must keep the driver's receipt for controlled waste for at least three years.

Equipment Choices That Change Your Waste Costs

The tank, trap or bin you install shapes what you pay for servicing in the years that follow. Taylex makes advanced secondary treatment systems and septic systems for homes and commercial sites. Fuji Clean makes the ACE1200 and ACE3000 residential wastewater treatment units. Envirocycle makes wastewater treatment systems for sewage and sullage, which is the greywater from sinks, showers and laundries. Rapid Plas makes a 3,000 litre underground septic tank for homes off the sewer. Only onsite wastewater systems approved by the WA Department of Health can be installed, so check the approved list before buying any unit.

For businesses, the right trap or separator keeps each waste in the cheapest stream to dispose of. SPEL makes the Puraceptor oil and water separator, now sold under the Spillceptor name, for capturing hydrocarbons on high-risk sites. Humes makes concrete pipes, pits and access chambers, along with sewage storage tanks. Coerco makes wastewater systems, effluent disposal systems and underground storage tanks from its head office in Malaga. Polymaster makes grease arrestors of 2,000 to 4,000 litres and septic tanks, plus enclosed bunds that catch leaks from intermediate bulk containers, known as IBCs.

Bin choice matters for anyone paying per lift. SULO makes wheelie bins in Australia that are tested to the AS 4123 standard for mobile waste containers. Mastec makes two-wheeled bins from 80 to 360 litres and four-wheeled bins of 660 and 1,100 litres. Satellite Industries makes the Tufway portable restroom, along with portable handwash stations and urinals. Vermeer makes vacuum excavators for construction, utility and pipeline work, which dig around buried services by sucking up soil instead of using a bucket.

What to Look Out For in a Waste Management Quote

A price well below the published disposal fee is a warning sign, because the receival fee is a fixed cost that every lawful load must pay. If a carrier offers to empty a 3,000 litre septic tank for less than the metro treatment plant charges to accept that load, ask where the waste is going. Waste holders must not let an unlicensed carrier transport controlled waste, so the responsibility does not rest only with the operator. Request the carrier's licence details and confirm them with the controlled waste team at DWER. Keep the receipt the driver gives you before the load leaves, because it shows the waste entered the tracking system.

Watch for quotes that leave out the disposal fee or say it will be passed on at cost without giving a figure. Vague disposal lines make offers hard to compare, and the final bill can arrive far higher than expected. Look for a stated volume or weight in each line, such as kilolitres pumped or tonnes tipped. Check whether travel, minimum charges and extra hose are included in the price or listed as extras.

Be wary of a single all-in price for mixed waste that includes asbestos, chemicals or tyres. Those items need different handling and different facilities, and a carrier who prices them as general rubbish may not be taking them to the right place. Asbestos must go to a facility licensed to accept it, and tyres need a licensed carrier. If the quote does not mention these items separately, find out how each one will be handled. A renovation can uncover hidden asbestos, so price the kitchen demolition and strip-out and its waste together after testing.

Paperwork You Should Receive After a Controlled Waste Job

For bulk liquid loads and larger packaged loads, the driver should give you a receipt before the waste leaves your site. Waste holders must keep that receipt for at least three years, so file it with the invoice. The invoice itself should list the volume or weight, the waste type and the disposal charge as separate lines.

For general rubbish and skip bins there is no tracking form, but a tip receipt or weighbridge ticket shows the weight that was charged. Ask for a copy whenever an overweight fee appears on the bill.

Missing paperwork makes it hard to dispute a charge later. Collect it at the time of the job, not weeks afterwards.

How to Get and Compare Waste Quotes Line by Line

Start by describing the waste in plain terms, including what it is, how much there is, how it is stored and where it sits on the property. Photos of the tank lid, pit, drums or pile help operators price access and volume without a site visit. For liquid waste, give the tank size in litres if you know it, along with the date of the last pump-out. For solid waste, give rough measurements in metres so the operator can estimate cubic metres or tonnes. Mention any slope, gate width, overhead wires or soft ground that the truck will need to cross.

When the quotes arrive, line them up side by side and split each one into the same parts. Those parts are the callout or minimum charge, labour or truck hours, travel, volume or weight, the disposal fee, the levy where it applies, extras and GST. Multiply each operator's unit rate by your estimated volume to see how the total was built. A quote with a lower hourly rate but an extra trip can cost more once disposal is counted. Check that each operator names the type of facility the waste will go to. Get every price in writing, including what happens if the volume turns out larger than expected.

Get at least three quotes for any waste job worth more than a few hundred dollars. Through The Quote Yard you can post a waste job once and hear from licensed operators who service your area. Describing the waste correctly leads to more accurate prices, and our guide to WA waste management services can help you name it. Compare the written quotes against the tables on this page before you accept one.

Ways to Lower Your Waste Bill

Sorting is one of the simplest ways to save. Keep green waste, clean fill, metal and recyclables out of the general bin, because general waste pays the full landfill rate including the levy in metro Perth. Clean concrete, bricks and soil can go in dedicated bins that cost less than mixed waste in the same size of bin. For liquid waste, keep wash water, oily water and grease in separate systems so each goes out at its own receival rate. Small quantities of household chemicals can go to the free Household Hazardous Waste Program instead of a paid collection.

Planned work costs less than emergency work, so service tanks and traps before they overflow. Booking pump-outs for several neighbouring properties on the same day lets owners share the travel cost, especially in regional areas. Businesses with grease traps can line up pump-outs with commercial plumbing maintenance and kitchen exhaust cleaning to limit kitchen downtime. Quarterly ATU servicing is a WA requirement, so build those visits into the yearly budget from the start. Keeping service records lets you show a new operator exactly what volume to expect. Request a condition check of the tank at each visit so small faults are found before they become emergency callouts.

Renovations and demolitions can produce large one-off waste bills. Having the demolition contractor separate concrete, metal and timber on site can reduce the volume going to landfill. Where old pipes or fixtures are replaced, check whether removal of the old fittings is included in the plumbing price. Getting the waste plan into the main quote avoids a separate skip or pickup bill at the end of the job.

Waste Operators Across Western Australia

We connect households, strata managers, businesses, farms and site managers with licensed waste operators in Perth and regional Western Australia.

▶ Perth Inner City 17 areas

CBD & Surrounds

Perth CBD Northbridge East Perth West Perth

Inner North

Subiaco Leederville Mount Lawley Highgate

Inner South

South Perth Victoria Park Como

Western Suburbs

Cottesloe Nedlands Crawley Dalkeith Applecross
▶ Greater Perth 26 areas

Northern Suburbs

Joondalup Wanneroo Ellenbrook Butler Morley Scarborough Karrinyup

Southern Suburbs

Fremantle Rockingham Baldivis Cannington Canning Vale Willetton

Eastern Suburbs

Midland Armadale Bassendean Byford Claremont

Perth Hills

Kalamunda Mundaring Gooseberry Hill Lesmurdie Helena Valley Darlington Glen Forrest Parkerville
▶ South West 25 areas

Peel

Mandurah Pinjarra Waroona Dwellingup Warnbro Safety Bay Secret Harbour

Bunbury Region

Bunbury Busselton Australind Harvey Collie Capel Donnybrook

Margaret River Region

Margaret River Dunsborough Augusta Cowaramup Yallingup

Great Southern

Albany Denmark Manjimup Pemberton Bridgetown Walpole Mount Barker
▶ Regional Western Australia 30 areas

Pilbara

Karratha Port Hedland Newman Tom Price Dampier Paraburdoo Marble Bar

Kimberley

Broome Kununurra Derby Halls Creek Fitzroy Crossing

Goldfields

Kalgoorlie Esperance Coolgardie Norseman Laverton Leonora

Mid West

Geraldton Carnarvon Meekatharra Kalbarri Exmouth Coral Bay

Wheatbelt

Northam Narrogin Merredin Moora York Toodyay

Waste Management Cost FAQs

How much is the WA waste levy and who pays it?
From 1 July 2026 the Waste Avoidance and Resource Recovery Levy is $90 per tonne, or $136 per cubic metre at rubble landfills that charge by volume. It applies to waste received at licensed landfills in the Perth metropolitan region, and to metro waste taken to licensed landfills outside the region. Landfill operators pay it to the state and include it in their gate fees. You pay it indirectly through the disposal line on your quote, so it does not appear as a separate bill.
Why is there no fixed price for a septic pump-out in WA?
We could not find a reliable published price for a householder pump-out, so we do not quote a band. The disposal part is public, with septage costing about $136 per kilolitre at the metro treatment plant for licensed carriers. Tank size, hose length, buried lids and travel distance then decide the rest of the price. Request a written quote that shows the volume pumped and the disposal rate as separate lines.
How is a grease trap pump-out priced?
Grease trap pump-outs can be priced on the size of the trap in litres, whether or not it is full. One Perth price list charges about $0.28 per litre plus GST, with a minimum of about $280 plus GST for traps up to 1,000 litres. A 2,000 litre trap would therefore cost up to about $560 plus GST each time, before any volume discount. The treatment plant charges about $147 per kilolitre including GST to accept grease waste.
What does a vacuum truck cost per hour in Perth?
Compiled supplier rates show about $165 per hour for a 1,000 litre unit with an operator. Trucks from 3,000 to 7,000 litres run about $170 to $225 plus GST per hour. Confirm whether disposal of the load is included, because fees at the receiving facility can add a lot to the bill. Check whether travel from the depot is billed and whether a minimum hire period applies.
How much does it cost to get rid of old tyres in WA?
Council drop-off fees for 2026-27 range from about $3 to $31 for a car tyre, with Perth metro sites at about $10 to $31. Four-wheel drive and light truck tyres cost about $25 to $30 each. Truck tyres cost about $10.50 to $68 each, and some metro sites do not accept them. Anyone carting tyres for a business needs a controlled waste carrier licence, and a tracking form is needed at 200 kilograms or more.
Do I pay the levy on waste from a regional property?
The levy applies to waste received at licensed landfills in the Perth metropolitan region. Waste generated and disposed of outside the metro region is not levied, which is one reason regional gate fees can be lower. One Wheatbelt shire charges about $40 per tonne for general waste in 2026-27. Waste collected in the metro region still attracts the levy even when it goes to a landfill outside the region.
How much does contaminated soil disposal cost?
One Perth metro council charges about $220 per tonne including GST for contaminated soil up to Class III, with a $100 minimum per load. The soil must be sampled and classified first, and a waste approval application is needed before delivery. Sampling and lab analysis are priced on quote because no published WA price list was found. Excavation and trucking are charged separately from the disposal fee.
Is household chemical disposal free in WA?
Householders can drop off paints, solvents, pesticides, small gas cylinders and household batteries free of charge at Household Hazardous Waste Program facilities. The program is funded through the waste levy and run with local governments. There is a limit of 20 kilograms or 20 litres for each material type. Commercial, farm, laboratory and veterinary chemicals are not accepted and need a licensed carrier.
Why do quotes for the same waste job vary so much?
Operators differ in how far their depot is from you, which facility they use and how they charge for travel and minimum time. Some include the disposal fee in an all-in price, while others list it separately at cost. Truck size also matters, because a smaller unit may need extra trips to the facility. Split each quote into the same lines before you compare totals.
What paperwork should I get after controlled waste is collected?
For bulk liquid loads and packaged loads of 200 kilograms or litres or more, the driver should give you a receipt before the waste leaves. Waste holders must keep that receipt for at least three years under the controlled waste rules. Your invoice should list the volume or weight, the waste type and the disposal charge. Keep these records with the quote in case you need to dispute a charge or prove where the waste went.

Specialist WA Services Linked to Waste Jobs

For Trades & Contractors - WA

Waste carriers, plumbers and site crews looking for work can browse current tradie jobs across WA, with related work including plumber jobs in WA and concreter jobs in WA.

Need Waste Removed in Western Australia?

Post your job and compare licensed operators for liquid waste, tyres, soil, bins and commercial waste anywhere in WA.

Get Free Waste Quotes

About This Guide

This page provides guidance information only. Details may change, always verify with the relevant authorities and seek independent professional advice where needed.

Reviewed by The Quote Yard Editorial Team

Published 17 November 2026 ·

How The Quote Yard Works

We connect you with independent local tradies and service providers, we don't perform any trade work ourselves. Tradies provide their own quotes directly to you. Always confirm licensing, insurance, and scope of work before engaging any provider.

Service availability may vary in regional WA. Verify licences at WA Building and Energy.
Prices are 2027 estimates for Western Australia based on recent published fees and price lists. They exclude site works, repairs, testing and long-distance mobilisation unless stated, and jobs without a published price are quoted individually.
Need work done? Get free quotes. Post a Job – It's Free