Bore Pump or Retic Not Working?

Describe the pump, the sprinkler timer and which zones fail, and compare quotes from licensed WA plumbers.

Get Free Plumber Quotes

Typical Costs (2027 Estimates)

Call-out and first hour (normal hours)$140-$280
Plumber hourly rate (normal hours)$110-$165/hr
Bore pump replaced (any type)$900-$2,800
Pressure tank replaced$420-$980
Retic solenoid valve repaired$120-$350
Pop-up sprinkler head replaced$35-$95 each
Testable backflow device tested$130-$380

These figures are 2027 estimates for WA homes. Electrical work on pump outlets, laboratory water tests and bore capping are priced on quote.

Bore and Reticulation Plumbing Services WA - Get Local Quotes

Bore and reticulation plumbing in WA covers the pumps, pressure tanks, valves and pipes that carry garden water from a backyard bore or the scheme supply to your sprinklers. Retic is the local word for an in-ground sprinkler system, and a licensed plumber handles the parts that touch drinking water, including backflow devices that stop water flowing back into the supply. Prices here are 2027 estimates for WA, from replacing a bore pump or pressure tank to repairing solenoid valves, the electric valves that switch each sprinkler zone on and off. Perth and Mandurah bores follow a roster of set watering days, a winter switch-off from 1 June to 31 August when sprinklers stay off, and a $100 fine for watering outside your days. Some garden bores need a licence from the Department of Water and Environmental Regulation (DWER), but a bore that waters a small home garden from shallow groundwater does not. Bore water must stay separate from the drinking water in the house, and a test at a NATA-registered laboratory shows whether it is safe for other uses. Bore watering rules change outside Perth and Mandurah, including in Bunbury, Busselton, Albany, Esperance and Kalgoorlie, where different water providers enforce them. Plumbers, bore drillers and electricians each handle different parts of the system, and a seasonal care plan helps you get the bore and retic ready before watering starts in September. Post your job to compare free quotes from licensed WA plumbers.

Bore and Retic Plumbers Across WA

Licensed plumbers replace bore pumps and pressure tanks, repair retic valves and fit and test backflow devices in Perth, Mandurah, the South West, the Great Southern and regional WA.

Get Free Quotes

At a Glance - Bore and Retic Plumbing in WA (2027 Estimates)

Job 2027 Estimate (WA) Suits Disruption Paperwork to Keep
Bore pump replaced (any type) $900-$2,800 Pump that hums, trips or gives no water Garden water off for the visit Pump brand and model on invoice
Submersible bore pump replaced $1,400-$3,600 Deeper bores with the pump down the casing Pump lifted and lowered again Invoice and warranty card
Pressure tank replaced $420-$980 Pump that starts and stops in quick bursts Short shut-off at the bore pump Tax invoice
Pressure switch or controller $180-$520 Pump that will not switch on or off Short shut-off at the bore pump Tax invoice
Retic solenoid valve repaired $120-$350 One station that will not turn on or off Valve box dug out Tax invoice
Controller supplied and fitted $250-$850 Old or faulty timer Program set to your roster days Printed program
Dual check valve installed $280-$550 Retic joined to scheme water Water off briefly at the meter Certificate if it counts as major work
Testable backflow device tested $130-$380 Yearly test of a testable device Short shut-off during the test Test report lodged with Water Corporation

Cost Depth: What Drives a Bore and Retic Bill

On pump jobs the pump itself and the labour to lift it from the bore make up the larger share, while retic repairs are driven by the call-out and the time spent finding the fault.

Limestone under the lawn, deep bores, iron-clogged bore screens and pumps that need an electrician as well as a plumber are the items that push a price higher.

All figures are 2027 estimates for WA. New bores, turf and paving repairs and regional travel are priced separately.

Where the Plumbing Ends and the Garden System Begins

Garden bores are narrow holes drilled down to the shallow groundwater under a block, each with a pump that lifts the water to the surface. Retic, short for reticulation, is the network of buried pipes, valves and sprinklers that spreads that water across lawns and garden beds. Each retic station is a group of sprinklers or drippers that switch on together when an electric valve opens. Some WA homes water only from a bore, some only from scheme water, which is the treated drinking supply from Water Corporation, Aqwest or Busselton Water. Other homes have both sources plumbed to the same garden, and that set-up brings in the strictest plumbing rules.

Under the WA plumbing regulations, water supply plumbing runs from the supply to the point where water leaves the pipes, called the point of discharge. The regulations say that point includes the outlet of a backflow prevention device required by the plumbing standards where an irrigation system is connected. This device is a valve assembly that lets water travel one way only, so garden water cannot be drawn back towards the house or the street main. Put simply, pipework up to and including that device is plumbing work, and the sprinkler pipes beyond it belong to the garden system.

Bore water brings a second concern, because it is not treated to drinking water standards. Healthy WA, the Department of Health's public advice site, says bore water cannot be connected to the scheme supply unless a backflow prevention device separates the two. The same advice says a licensed plumber must make that connection. Water Corporation lists a bore pump cross-connected to house plumbing, meaning joined to the same pipes, as a backflow risk. For other plumbing work around the home, see the plumbing services guide for WA.

Bore and Retic Repair Prices for 2027

The figures below are 2027 estimates, widened where two published WA price ranges differed. Plumbers price small retic faults by the call-out plus parts, while pump and tank jobs are quoted as a supplied and fitted price. For a normal hours call-out with the first hour, expect about $140 to $280, and further time runs at about $110 to $165 an hour. After hours or weekend attendance adds a call-out of $240 to $520 before any work starts. You can compare these rates with other everyday plumbing jobs in the WA plumber pricing guide.

Bore Item 2027 Estimate (WA) What Moves the Price
Bore pump replaced (any type) $900 - $2,800 Pump type and bore depth
Submersible bore pump replaced $1,400 - $3,600 Depth, motor size, lifting the pump
Bore pump and pressure tank together $1,900 - $4,600 Tank size, pump brand, new pipework
Pressure tank replaced $420 - $980 Composite or steel tank, volume, access
Pressure switch or pump controller $180 - $520 Simple switch or electronic controller
Bore site assessment and flow test $180 - $450 Travel, whether the pump must be lifted
Bore redevelopment and cleaning $900 - $2,600 Iron build-up, sand, bore depth
Annual pump and bore service $180 - $420 Number of pumps, filters and tanks
Iron filtration fitted $1,400 - $5,500 Filter size, self-flushing set-up, flow needed
New bore drilled and equipped $4,500 - $11,500 Depth to water, ground, pump choice

Retic repairs cost less, because the parts are smaller and the work is close to the surface. Retic fault finding with a repair call-out comes to about $120 to $260, with parts charged on top. Replacing a solenoid valve, the electric valve that opens one station, runs at about $120 to $350 per fault. Pop-up sprinkler heads cost about $35 to $95 each, and rotors, which turn slowly to throw water further, at $65 to $150 each. Fixing a broken lateral, the pipe that feeds sprinklers along one station, costs about $140 to $380. New controllers supplied and fitted sit at around $250 to $850, and a smart Wi-Fi upgrade at $380 to $950.

Retic and Backflow Item 2027 Estimate (WA) Notes
Retic fault find and repair call-out $120 - $260 Parts charged separately
Solenoid valve replaced or repaired $120 - $350 Per fault, valve box access
Pop-up sprinkler head replaced $35 - $95 each Nozzle type and brand
Rotor sprinkler replaced $65 - $150 each Larger lawns and verges
Broken lateral repaired $140 - $380 Depth, roots, limestone under the lawn
Rain sensor added during other work $90 - $220 Wired or wireless sensor
Winter shutdown and spring restart $140 - $320 Both visits combined
Dual check valve supplied and installed $280 - $550 Non-testable valve
Testable double check valve supplied and installed $380 - $750 Needs yearly testing once fitted
Testable backflow device tested $130 - $380 per device Result lodged with Water Corporation

No published WA price range covers a new weatherproof outlet for a bore pump, a laboratory water test or capping an old bore, so those items are priced on quote. Adding price ranges together does not give a reliable total, because a single visit can fix several faults for one call-out. For example, a $140 to $280 call-out plus a $120 to $350 solenoid repair gives $260 to $630 only if the plumber charges both items in full. Request a quote with each line shown separately so you can see which figures apply. Regional travel and limestone digging are also extra.

Plumber, Driller, Electrician or Retic Installer

Four kinds of worker can touch a bore and retic system, and each has a different role. Drillers drill the bore, and the state recommends an experienced and accredited driller, ideally one licensed through the Australian Drilling Industry Association. The driller should hand over a bore log, which is a written record of depth, soil layers, water yield and pump details. Those records can be invaluable for you or a later owner, according to Be Groundwater Wise, the state's garden bore information site. Keep the log with your house papers from the day the bore is finished.

Licensed plumbers handle any work that connects to, or protects, the drinking water supply. That includes fitting or replacing a backflow device, tying a bore into house pipes where the rules allow it, and joining retic to the scheme supply. Minor plumbing work in WA is defined as testing, maintenance, repair or replacement of existing plumbing, and it excludes replacing a testable backflow device. Any work outside that minor category is major work, which needs extra paperwork, explained in the licences section below. The plumber should tell you at the quote stage which category your job falls into. Swapping a worn solenoid valve on the garden side does not touch the drinking supply, but changing a backflow device does.

Pump wiring is a separate trade with its own licence. Fixed wiring, a new outdoor power outlet or a hardwired isolator switch, a fixed switch that cuts power to the pump, is electrical work for a licensed electrician. If the pump has no suitable outlet, book an electrician for an outdoor power point before the plumber arrives, so the pump can be tested on the day. Retic installers and landscapers can lay sprinkler pipes and heads beyond the backflow device, and the regulations end plumbing work at that device's outlet. Before you sign, find out from any installer who will certify the connection to the water supply.

The regulations also contain a narrow exception for owners of properties that are not supplied by a water services provider. On such a place, an owner or occupier, or a person helping them without pay, may replace a water pump that supplies water to it. That exception does not apply to properties that have scheme water from Water Corporation, Aqwest or Busselton Water. It also covers only the pump swap, so pipework, backflow devices and electrical work still need the right licence. In practice, it suits blocks with no scheme water connection, such as rural homes that rely on a bore or tank.

Roster Days, the Winter Switch-Off and Fines

Garden bores in Perth and Mandurah follow a two-day sprinkler roster, a set of two watering days each week, from 1 September to 31 May. On each rostered day you may water once, either before 9am or after 6pm, according to the WA Government's bore restrictions page. Bore users in Perth and Mandurah follow the same rosters and times as scheme water users, according to Water Corporation. The winter switch-off then runs from 1 June to 31 August each year, when sprinklers must stay off across Perth, Mandurah and the South West. Using sprinklers on the wrong day or during the switch-off can bring a $100 fine.

Your watering days come from the last digit of your street number, or your lot number if the home has no street number. Where an address covers a range, such as 22 to 24, Water Corporation says to use the higher number. Unit numbers do not change the result, because the roster follows the street number of the whole property. The table below shows the Perth and Mandurah bore days from the WA Government page, updated in October 2026. Where several homes share one bore, each property waters on its own roster days, and if that is not possible, only on the bore's permitted days. Owners can register a shared bore with the department to avoid a fine, the WA Government says.

Last Digit of Street Number Perth and Mandurah Bore Watering Days Times Allowed
1 or 8 Wednesday and Saturday Once, before 9am or after 6pm
2 or 9 Thursday and Sunday Once, before 9am or after 6pm
3 or 0 Friday and Monday Once, before 9am or after 6pm
4 Saturday and Tuesday Once, before 9am or after 6pm
5 Sunday and Wednesday Once, before 9am or after 6pm
6 Monday and Thursday Once, before 9am or after 6pm
7 Tuesday and Friday Once, before 9am or after 6pm

Repairs and testing have their own allowance in the rules. The Water Agencies (Water Use) By-laws 2010 let a system be run for installation, repair or testing to the minimum extent necessary. The rules treat that as no more than two minutes per station, and Be Groundwater Wise suggests doing the work on your roster days. Bore maintenance testing is also permitted during the winter switch-off, according to Water Corporation. Plumbers who test every station after a valve repair should keep each run short and note the times on the job sheet.

Faulty controllers do not excuse a breach of the watering rules. A faulty controller does not stop a fine, and Water Corporation says sprinklers used outside your set times can still bring one. New lawns and gardens can get a temporary watering exemption through Water Corporation or the Water Efficiency Measures team on 1800 508 885. Breaching the conditions of a new garden exemption can bring a fine of up to $500. Check the current rules on the Water Corporation website before the controller is reprogrammed each spring.

Three-Day Roster for Some Bore Owners

Be Groundwater Wise lists a three-day sprinkler roster that bore users in Perth and Mandurah can apply for under strict conditions. The property must not be connected to scheme water and must sit in a bush fire prone area as defined by the Department of Fire and Emergency Services. The amount of water taken from the bore must also not need a licence.

Only the owner or occupier can apply, one application per property, and the approval stays tied to the property. Questions go to the Water Efficiency Measures team on 1800 508 885.

Rules checked on WA Government and Water Corporation pages in November 2026. Confirm your own days before setting a controller.

Keeping Bore Water Out of the Drinking Supply

Backflow is a reversal of the normal flow in a water supply system, as Water Corporation defines it. It can happen when mains pressure drops below the pressure inside the property, or when a pump pushes water back at a higher pressure. One example given by Water Corporation is a garden hose left submerged in a container of liquid. Bore pumps joined to house pipes are the larger risk, because they can force untreated groundwater towards the street main. The fix is physical separation, either a backflow device or two supplies that never touch.

Standard homes already have some protection at the meter. Water Corporation's 20mm and 25mm meters have built-in dual check valves, which are two one-way valves in a row, and it says residential-only properties with those meters already have sufficient backflow prevention at the boundary. That boundary protection guards the street main, but it cannot stop a cross-connection on the property's own pipes from reaching household taps. For that reason, Healthy WA still says a backflow device must separate any bore connection from the scheme supply. RMC Reliance Valves makes backflow valves, including its RWC BEECO range, in Australian factories run by Reliance Worldwide. Properties with a water service pipe larger than 25mm, or a separate fire service for hoses or sprinklers, are assessed for backflow risk separately, and Water Corporation always rates fire services as medium risk.

Testable devices bring an ongoing duty for the property owner. Testable boundary devices, which have test points so a tester can check them, must be tested when first fitted, after any maintenance and every 12 months by an accredited tester. The test report must be lodged online no later than 5 working days after the test. Water Corporation does not accept test reports for zone or individual devices, which are valves that protect one part of a property. Find out from your plumber which kind of device you have, and keep the test reports with the bore log. Device types are covered in more depth in the backflow prevention guide for WA.

Some homes have a top-up line that lets scheme water refill a tank or sump, a pit that collects water, that the bore also feeds. Those set-ups need careful design, because the scheme water must never be able to draw bore water back. Your plumber can show you where the separation sits and what kind of device or gap protects it. If you are unsure whether old work was done properly, a licensed plumber can trace the pipes and confirm whether the two supplies are joined.

Signs Worth Checking at the Headworks

At the headworks, the pipes and valves at the top of the bore, look for any pipe that runs towards the house, a laundry or a toilet cistern. Look also for valves that let the retic switch between bore and scheme water without a backflow device in between.

Discoloured water at an indoor tap, iron stains in a toilet or a pump that runs with the sprinklers off are reasons to book a check for any join between bore and drinking water pipes.

These are prompts for an inspection, not a diagnosis. Only a licensed plumber should alter pipework connected to scheme water.

When a Garden Bore Needs a DWER Licence

Licensing for the bore itself sits with the Department of Water and Environmental Regulation, known as DWER. According to the WA Government, garden bores do not need a licence when they irrigate small areas of domestic garden and lawn from the shallow watertable aquifer. Here, an aquifer means a layer of sand or rock that holds groundwater, and Perth's shallow one is called the Superficial aquifer. In a proclaimed groundwater area, which is an area declared under state water law, you need a licence to irrigate 0.2 hectares (2,000 square metres) or more.

Two other cases also need a licence from the department. Using the bore for a commercial purpose needs one, and so does taking water from an artesian aquifer such as the Leederville or Yarragadee, two deep aquifers under the Perth region. Artesian aquifers are deeper layers where the water is held under pressure between harder layers above and below. The Department of Water and Environmental Regulation handles these licences and the Perth groundwater map. That map shows the estimated depth to the watertable, salinity (saltiness) and the iron staining risk for a property.

Your local council may have its own requirements for bores, so check with it before a new bore is drilled. Keep any approval or letter from the council with the bore log. Buyers will want to see those papers when the house is sold. Where the property has an older septic tank and leach drains, the buried pipes that spread septic water into the soil, see the septic tank services guide. The driller and the plumber should both know where tanks, drains and soakwells, the buried pits that take roof water, sit before any digging starts.

Submersible Pumps, Surface Pumps and Pressure Tanks

Submersible pumps sit down inside the bore casing, the pipe that lines the hole, below the water level, and push water up to the surface. Surface pumps sit above ground at the headworks, which is the cluster of pipes, valves and fittings at the top of the bore. The choice depends on how deep the water sits and how much flow the retic stations need. Your driller's bore log and a flow test give the plumber the numbers to size a replacement pump properly.

Several makers supply bore pumps that WA plumbers fit. Grundfos makes the SQ, a compact 3-inch multistage pump, meaning it has several spinning impellers in a row, which it lists for home water supply and irrigation. Davey makes 4-inch borehole pumps that fit a standard 4-inch bore casing, joined directly to an electric motor that also sits underwater. Lowara makes submersible borehole pumps, and its owner Xylem says they suit irrigation even where the water carries a lot of sand. Get the pump brand, model and motor size written on the quote so you can check the specifications yourself.

Pressure tanks store a small amount of water under air pressure, so the pump does not start every time a valve opens. Davey makes SuperCell pressure tanks in composite, a tough plastic and fibre mix, and steel versions. Onga makes Wellmate composite pressure tanks and the Pentek Intellidrive, a variable speed controller for bore pumps, under the Pentair group. This type of controller changes the motor speed to match demand, which can keep pressure steadier across stations of different sizes. Worn tanks and failed pressure switches, which turn the pump on and off as pressure changes, can make the pump start and stop in quick bursts, which is known as short cycling. Replacing a pressure tank costs about $420 to $980, and a pressure switch or controller at $180 to $520.

Bore Pump Faults a Plumber Checks First

When a pump hums but delivers no water, the plumber starts with a few likely causes. The water level in the bore may have dropped below the pump intake, the pump may have lost its prime, or the impeller, the spinning part that pushes water, may be worn by sand. Priming means filling a surface pump and its suction pipe with water so it can draw from the bore. Iron bacteria, which are microbes that feed on dissolved iron and form slime, are another possible cause. Their build-up appears on the Be Groundwater Wise list of things that can affect a pump's efficiency.

Low pressure across every station suggests a problem at the pump, tank or main line. Low pressure on one station suggests a leak, a blocked filter, a partly open valve or too many sprinklers on that line. Pumps that run with no sprinklers on can mean a leak in buried pipe or a cross-connection that keeps drawing water. A tripped safety switch, burnt smells or a pump that will not start need an electrician as well as a plumber, because the fault may be in the wiring.

What You Notice What a Plumber Checks Possible Next Step
Pump runs, no water at sprinklers Water level, prime, intake screen Re-prime, clean or replace pump
Pump starts and stops rapidly Air pressure in the tank, pressure switch settings Top up tank air, or replace tank or switch
Weak spray on every station Pump output, filters, main line leaks Flow test, filter clean, pipe repair
One station weak or dead Solenoid valve, wiring to that valve, lateral pipe Valve repair or lateral repair
Pump runs with sprinklers off Buried leaks, stuck valves, cross-connections Leak trace, valve repair, separation work
Orange stains on paving and walls Iron in the water, sprinkler throw Filter, redirect heads, bore treatment

Before the visit, write down what you see, when it started and which stations are affected. Note whether the fault appeared after a storm, a power cut or work on the house. Take a photo of the pump label and the controller screen, because the model numbers help the plumber bring the right parts. Those details can save a second call-out for parts.

Iron Staining, Odours and Bore Water Testing

Orange or brown marks on paving, walls and fences come from iron dissolved in the groundwater. When the water meets air, the iron forms rust-coloured particles that settle wherever the sprinklers land. Perth's groundwater map, published by the WA Government, shows an iron staining risk rating for each property, which is useful before you drill or buy. Check whether bore water has changed colour or has any odours, because Be Groundwater Wise says both can signal contamination or iron bacteria.

Treatment ranges from simple fixes to filter systems. Turning sprinkler heads away from paving and walls is the cheapest step, and it costs only the plumber's time if heads need adjusting. Puretec makes the IRX range of iron removal filters, which the maker says reduce staining and deposits from iron. Puretec also makes BoreSafe products, which it describes as breaking down iron build-up in bores. Fitting iron filtration costs about $1,400 to $5,500, depending on the flow the garden needs and the filter size. Bore redevelopment, where a contractor cleans the screen, the slotted pipe that lets water in, and the casing to restore flow, is estimated at $900 to $2,600.

Healthy WA says bore water should never be used for drinking unless it has been tested and treated for that purpose. If bore water is the only supply for a home, Healthy WA says to test it at least once a year at a NATA-registered laboratory, asking for a Standard Drinking Water Test. NATA is the national body that accredits testing laboratories. For filling pools and spas, Healthy WA prefers scheme water, because bore water may need more chemicals and can stain. Read the bore water advice on the WA Department of Health website before using bore water on edible plants.

Regular samples to check salinity and pH are another Be Groundwater Wise suggestion. Salinity is the amount of dissolved salt, and pH measures whether the water is acidic or alkaline. Changes in either can point to groundwater contamination, damaged bore casing or pumping too much water, according to the same tips. Owners should also check the Contaminated Sites Database, Healthy WA adds, to confirm they are not drawing water from a known contaminated site. Contact your local Environmental Health Officer if you notice an unusual taste, smell, colour or sediment. Animals avoiding the water are another warning sign of contamination on the Healthy WA list.

Retic Valves, Sprinkler Heads and Broken Pipes

Retic faults can sit in four places: the controller, the solenoid valves, the pipes or the sprinkler heads. Each solenoid valve has a small electric coil that lifts a rubber diaphragm when the controller sends power, letting water through to one station. Holman makes a 25mm solenoid valve with a manual bleed screw, which lets the valve be opened by hand when there is no power. Toro makes 2400 Series electric valves, which its Australian site says are designed mainly for residential use. Your plumber can test the coil, clean the diaphragm or replace the whole valve, at about $120 to $350 per fault.

Buried pipes break from roots, digging, vehicle weight and old joints. Wet patches, sunken soil or a station that never reaches full pressure all suggest a leak in the lateral or in the main line that feeds the valves. Philmac makes metric tapping saddles, which clamp onto a pipe to add a branch, and PUSH fittings that join polyethylene pipe, the flexible black pipe used in retic. Iplex makes Poliplex PE100 polyethylene pipe, and Vinidex makes polyethylene and PVC pressure pipe systems for irrigation and rural water supply. Limestone or roots can push a broken lateral repair towards the top of its $140 to $380 range.

Sprinkler heads wear, clog with sand and get hit by mowers. Pop-up heads that stick up or will not retract can be cleaned or swapped for $35 to $95 each. Mixing sprays and rotors on one station can water some areas much harder than others, so keep head types matched on each station. Drip lines suit garden beds where sprays would wet paths or walls. Netafim makes Techline dripline, one of several drip products listed on its Australian site. For a full new system or a new station layout, see the reticulation installation and repairs guide.

Water pressure from the scheme supply affects how many sprinklers each station can run. Have the plumber check pressure at a garden tap before adding heads or stations. Where the main water pipe from the meter is old or leaking, see the water pipe replacement guide for options. Leaks on your side of the meter are your responsibility, and Water Corporation's faults line 13 13 75 handles leaks on its side.

Programming a Controller to Your Watering Days

The controller is the timer that tells each solenoid valve when to open and for how long. Older units use dials and buttons, while newer ones connect to Wi-Fi and change run times based on local weather. Holman makes the WX8 Wi-Fi irrigation controller, sold with its EVIE sensor. Many smart models can be changed from a phone app, which helps when the watering days need updating. Smart controllers do not change the roster rules, so the days and times still need to match your house number.

Set for the wrong days, a controller will keep breaking the roster every week until someone changes it. Check that the clock, date and season settings are right after every power cut. Set only your two rostered days, one start time per day, and start times before 9am or after 6pm. Switch the controller off, or set it to a rain or off mode, from 1 June to 31 August. Keep a printed copy of the program in the controller box for the next person who touches it.

Rain sensors stop the system from running during or after rain. Adding one during other retic work is estimated at $90 to $220. Sensors save water but do not replace the roster, so the days still need to be set correctly. Replacing a controller costs about $250 to $850, and smart Wi-Fi upgrades at $380 to $950.

Controller Settings to Check Before Spring

Confirm the date and time, your two watering days, a single start time per day before 9am or after 6pm, and run times for each station. Remove any extra start times left from earlier owners.

Run each station for no more than two minutes during testing, the most the WA Government allows when repairing or testing a system.

Fines can still apply when a controller fault causes a breach, so check settings after storms and power cuts.

Rainwater Tanks, Greywater and Other Garden Water

Rainwater tanks can feed the garden through their own pump and a separate retic line. The winter sprinkler switch-off does not apply to irrigation systems that use water collected in rainwater tanks, Water Corporation says. Connecting a tank pump to garden irrigation is estimated at $450 to $950. Where the tank also connects to the house or to scheme water, backflow protection and a switching device, which swaps the supply between tank and scheme water, are needed. Those connections are covered in the rainwater tank plumbing guide.

Greywater is used water from showers, baths and washing machines, and it can be diverted to garden beds under health rules. Greywater systems need their own approvals and must be kept apart from bore and scheme water lines. Label each pipe at the controller and valve boxes, so a later repair does not join two water sources by mistake. The approval steps are set out in the greywater installation and maintenance guide. Homes with an aerobic treatment unit, a powered septic system, may also have irrigation lines for treated wastewater, which are separate again from the retic. Those lines belong to the wastewater system and should never be joined to bore or scheme water pipes.

Bore and Retic Rules Outside Perth

Garden bore rules in WA are divided into numbered areas. In North Area 1 and South Area 2, which includes Kalgoorlie, Geraldton and Kalbarri, bore owners may water on any day, once a day, before 9am or after 6pm. In South West Area 4, which includes Albany, the same daily rule applies from 1 September to 31 May, followed by the winter switch-off. Esperance Shire and Munglinup move to a two-day roster from 1 December 2026, with a winter switch-off starting on 1 June 2027.

Area Bore Watering Rule Winter Switch-Off
Perth and Mandurah (Area 3) Two rostered days a week, once a day, before 9am or after 6pm 1 June to 31 August
South West (Area 4), including Albany Any day, once a day, before 9am or after 6pm, 1 September to 31 May 1 June to 31 August
North (Area 1) Any day, once a day, before 9am or after 6pm Not listed
South (Area 2), including Kalgoorlie and Geraldton Any day, once a day, before 9am or after 6pm Not listed
Esperance Shire and Munglinup Two-day roster from 1 December 2026, aligned with scheme water days From 1 June 2027

Different water providers enforce the rules in different towns. Sprinkler restrictions are enforced by water service providers, and the WA Government names Water Corporation, Aqwest and Busselton Water. Aqwest supplies Bunbury, and breaches there are reported to Aqwest, while Busselton breaches go to Busselton Water. Breaches of a council's own sprinkler use in winter are reported to the council directly.

Travel adds to regional prices, and parts for less common pumps may need to come from Perth. Owners around Bunbury can compare local rates through plumbers in Bunbury and the South West. In Albany, local plumbing costs are listed in the Great Southern plumber guide. Properties in the Perth Hills can check Swan Valley and Perth Hills plumbers for nearby help. Before the trip is booked, check whether the plumber carries standard pump and valve parts in the van.

A Seasonal Care Plan for Bore and Retic

Twelve maintenance tips for garden bores appear on Be Groundwater Wise, and several of them suit a yearly routine. Inspect the headworks, casing and pump regularly for scale (a hard mineral crust), rust or damage. Keep a protective cover over the bore so the headworks stay easy to find and reach. During the switch-off, run the system only as much as needed to keep the pump in good working order. Never flush waste down a borehole, because it can pollute the groundwater that you and your neighbours share.

Late August is a good time to book a service before the watering season starts on 1 September. Before spring, check the system is not leaking and replace broken or clogged sprinkler nozzles, as Be Groundwater Wise advises. One visit can cover pump pressure, the air pressure in the tank, filters and every station. The annual pump and bore service is estimated at $180 to $420, and a combined winter shutdown and spring check at $140 to $320.

If you no longer use a bore, have it professionally capped so it is safe and cannot let contaminants reach the groundwater. That advice comes from the final maintenance tip on Be Groundwater Wise. No published WA price range covers closing a bore, so ask for a written quote that names who will seal the casing and how. Keep the paperwork for future buyers, who may otherwise assume the bore still works. Remove or label any old pipe that once linked the bore to the retic, so nobody reconnects it without checking.

Buying or Renting a Home With a Bore

Bores can add value to a garden, but only if they work and were installed properly. Before buying, ask the seller for the bore log, any council approval, recent service records and backflow test reports. Find out also whether bore water reaches any tap inside the house or any toilet cistern. Your pre-purchase plumbing inspection can include a look at the headworks, the retic connection and any backflow device. Check the Perth groundwater map for the iron staining risk before you assume stains on the paving will wash off.

Landlords and tenants should agree in writing who programs the controller and who pays for retic repairs. A controller set by a previous tenant can still break the roster, so check the program when each tenancy starts. Leave the watering days and a copy of the program inside the controller box at the start of each tenancy. Broken pipes that flood the garden or the house are plumbing repairs, and the first steps are in the burst pipe repairs guide. Tenants should report a pump that runs constantly, because it can waste power and wear out the motor. Landlords can add a yearly bore and retic service to the routine maintenance list for the property.

Licences, Certificates and Complaints

Plumbers in WA are licensed by the Plumbers Licensing Board, with support from Building and Energy, part of the Department of Local Government, Industry Regulation and Safety. You can check a plumber's licence through the Building and Energy online search or by calling 1300 489 099. Ask to see the licence card before work starts, check the expiry date and confirm it covers the type of work. If an employee will do the job, find out who the licensed plumbing contractor is, because the contractor certifies the work. More detail is on the WA Government website under Building and Energy.

Major plumbing work carries two pieces of paper. The plumbing contractor must lodge a notice of intention, which tells the Plumbers Licensing Board about the job in advance, at least 24 hours before work starts. Within 5 working days after the work is completed, the contractor must give the Board a certificate of compliance, a signed statement that the work meets the plumbing standards, and give you a copy. WA Building and Energy describes that copy as the blue certificate and suggests you store it with your records. Installing a testable backflow device falls outside minor work, so expect both documents for that job.

Homeowners in WA may do only a short list of plumbing tasks without a licence, according to the WA Government. The list covers a shower head, a tap other than a thermostatic mixing tap, which blends hot and cold to a set temperature, a cistern washer and a water filter cartridge. It also covers clearing a blocked fixture or waste pipe with a plunger, though a toilet that stays blocked needs blocked toilet repair services, and every other plumbing task needs a licensed plumber. Garden tap washers fall under the tap item, but connecting retic or a bore to the water supply does not appear on the list.

When work is faulty, give the contractor a chance to fix it first. If that fails, Building and Energy can take a complaint, and the Plumbers Licensing Board can require a contractor to fix work that breaks the rules for up to six years after completion. Contract and payment disputes go to Consumer Protection on 1300 304 054. Keep quotes, invoices, photos and certificates together so the record is complete if a dispute starts. Write down dates and names from every phone call, since those notes help Building and Energy follow the timeline.

What to Look Out For in Bore and Retic Quotes

Quotes that say only fix retic or service bore give you nothing to compare. Look for the pump brand and model, the motor size and whether the price includes pulling and re-lowering a submersible pump. Check whether the quote names the backflow device type, and whether it is testable. Watch for a quote that joins bore and scheme water without any mention of separation or a backflow device. That omission is a reason to ask more questions before agreeing to the work.

Be careful with offers to rewire the pump outlet as part of a plumbing quote. Electrical work needs a licensed electrician, so the quote should name who will do it and under which licence. Be wary of controller programming that ignores your roster days, because each breach can bring a $100 fine. Also check whether the quote covers making good, which means putting back turf, paving or limestone after a pipe is dug up.

Red Flags in a Bore or Retic Quote

No licence number, no mention of a notice or certificate for major work, a cash price with no tax invoice, or a plan to connect bore water to a house tap.

Vague parts lists, no warranty terms on the pump, and no plan to test each station after repairs are also signs to compare another quote.

Check every licence on the Building and Energy search before work starts.

Getting Quotes You Can Compare

Give every plumber the same details so their prices line up. Send photos of the headworks, pump label, pressure tank, controller and any valve boxes. List the stations that fail, the water source for each and whether scheme water reaches the retic. State your suburb or town, because travel and parts supply change the price outside the metro area. Mention any limestone, paving or tree roots near the faulty pipes, since digging conditions change the labour time. Include your roster days, so the plumber can plan testing on a day when stations may run.

Request that each plumber separates the call-out, labour, pump or valve parts, backflow work and any electrician costs. Get the warranty on the pump and on the workmanship in writing, along with who to call if the pump fails in summer. Written quotes should say whether a notice of intention and a certificate of compliance apply. Compare the total for the same scope, not the lowest call-out figure. For metro rates see the Perth plumber guide, and for drilling a new bore see the garden bore installation guide.

Timing affects both the price and how soon a plumber can come. Every retic system in Perth and Mandurah may come back on from 1 September, so spring bookings can fill quickly. Booking a service in winter gives time to fix faults before the first rostered day in September. Emergency visits for a burst main line in summer cost more, with after hours call-outs estimated at $240 to $520.

Related Work to Book in the Same Visit

Combining small jobs under one call-out can lower the total cost. While testing a backflow device, the plumber can also check the pressure tank, the pressure switch and each solenoid valve. If a leak on the house side is suspected, add water leak detection so a hidden fault is found while the plumber is there. Have each extra task priced separately so you can drop any that are not needed.

Garden upgrades can change what the retic needs to do. New lawn, garden beds or paving can move sprinkler positions, so plan the retic before the landscaping is finished. Drip and sprinkler options for new beds are covered in the irrigation and garden watering guide. Trenching for new pipes is a separate job, and a trenching contractor can dig long trenches before the plumber connects the pipes. Book the plumber last to test the whole system once the ground work is done.

Bore and Retic Plumbers in Every WA Region

We connect WA homeowners, landlords and property managers with licensed plumbers who repair bore pumps, retic systems and backflow devices from Perth to the regions.

▶ Perth 28 areas
Perth CBD Joondalup Wanneroo Butler Alkimos Stirling Scarborough Hillarys Karrinyup Morley Bayswater Bassendean Belmont Victoria Park South Perth Melville Applecross Canning Vale Willetton Cannington Fremantle Cockburn Rockingham Baldivis Gosnells Armadale Byford Ellenbrook
▶ Mandurah & Peel 20 areas
Mandurah Halls Head Dawesville Falcon Erskine Silver Sands Madora Bay San Remo Greenfields Meadow Springs Lakelands Coodanup Pinjarra Ravenswood Waroona Dwellingup North Dandalup Serpentine Jarrahdale Boddington
▶ Bunbury & South West 24 areas
Bunbury Australind Eaton Dalyellup Gelorup Capel Busselton Vasse Dunsborough Yallingup Margaret River Cowaramup Augusta Harvey Brunswick Junction Collie Donnybrook Balingup Nannup Bridgetown Boyup Brook Manjimup Pemberton Northcliffe
▶ Swan Valley & Perth Hills 24 areas
Guildford Midland Herne Hill Middle Swan West Swan Upper Swan Caversham Baskerville Henley Brook Swan View Helena Valley Kalamunda Gooseberry Hill Lesmurdie Walliston Carmel Pickering Brook Mundaring Glen Forrest Darlington Parkerville Chidlow Roleystone Bedfordale
▶ Avon Valley & Wheatbelt 22 areas
Northam York Toodyay Beverley Bakers Hill Clackline Wundowie Goomalling Dowerin Wongan Hills Cunderdin Tammin Kellerberrin Merredin Wyalkatchem Trayning Nungarin Quairading Brookton Corrigin Bruce Rock Narrogin

Bore and Retic Plumbing FAQs

How much does a bore pump replacement cost in WA?
Bore pump replacement is estimated at $900 to $2,800 in 2027, depending on the pump type and bore depth. Submersible pumps that sit down the bore cost about $1,400 to $3,600, because they must be pulled up and lowered again. Replacing the pump and pressure tank together runs to about $1,900 to $4,600. Get the brand, model and motor size written on the quote.
Does the sprinkler roster apply to garden bores in Perth?
Yes, garden bores in Perth and Mandurah have two rostered days a week from 1 September to 31 May. You may water once on each rostered day, before 9am or after 6pm. Bore users follow the same rosters and times as scheme water users, according to Water Corporation. Sprinklers must stay off from 1 June to 31 August, and breaches can bring a $100 fine.
Do I need a licence for a garden bore in WA?
Garden bores that water a small domestic garden and lawn from the shallow watertable aquifer, the groundwater layer nearest the surface, do not need a licence. In a proclaimed groundwater area, you need one if you irrigate 0.2 hectares or more. Commercial use and water taken from an artesian aquifer, such as the deep Leederville or Yarragadee, also need one. The Department of Water and Environmental Regulation handles these licences.
Can bore water be connected to my house plumbing?
Healthy WA says bore water cannot be connected to the scheme supply unless a backflow prevention device separates the two. The connection must be made by a licensed plumber. Bore water should never be used for drinking unless it is tested and treated for that purpose, Healthy WA adds. Have your plumber confirm that no bore pipe reaches an indoor tap or toilet.
Who can repair my retic system?
Any work that connects to or protects the drinking water supply, including backflow devices, must be done by a licensed plumber. The WA regulations place the end of water supply plumbing at the outlet of the backflow device that connects an irrigation service. Sprinkler pipes and heads beyond that point are part of the garden system. Wiring for a pump or controller outlet is work for a licensed electrician.
Why does my bore water stain paving and walls orange?
The stains come from iron dissolved in the groundwater, which forms rust-coloured particles once it meets air. The Perth groundwater map shows an iron staining risk rating for each property. Turning sprinklers away from hard surfaces is the cheapest fix. Iron filtration is estimated at $1,400 to $5,500 to fit, depending on flow and filter size.
Can I run my sprinklers to test them during the winter switch-off?
Bore maintenance testing is permitted during the switch-off, according to Water Corporation. The WA Government allows systems to be run for installation, repair or testing to the minimum extent necessary. It treats that as no more than two minutes for each station. Be Groundwater Wise suggests doing that work on your roster days.
Will I be fined if my controller malfunctions?
Yes, Water Corporation says controller malfunctions do not prevent fines. Sprinklers used outside your allocated times can bring a $100 fine. Check the clock, date and watering days after every power cut. Adding a rain sensor during other retic work is estimated at $90 to $220, but it does not replace correct roster settings.
How often does a backflow device need testing?
Testable boundary devices must be tested when first fitted, after any maintenance and every 12 months, Water Corporation says. The accredited tester must lodge the report online no later than 5 working days after the test. Testing is estimated at $130 to $380 per device in 2027. Test reports for zone or individual devices are not accepted by Water Corporation.
What should I do with a bore I no longer use?
Have an unused bore professionally capped, as Be Groundwater Wise advises, so it is safe and cannot let contaminants into the groundwater. No published WA price range covers capping, so ask for a written quote. Remove or label any old pipe that linked the bore to the retic. Keep the paperwork so a future buyer knows the bore is closed.

Garden and Outdoor Specialists

For Trades & Contractors - WA

Plumbers who service bore pumps, retic and backflow devices can pick up new work on our WA job leads board, alongside plumber jobs in WA and irrigation plumber jobs.

Ready to Fix Your Bore or Retic?

Post your job and compare quotes from licensed WA plumbers for bore pumps, retic valves and backflow work.

Get Free Plumber Quotes

About This Guide

This guide is general information only, and WA watering rules, licensing requirements and product details can change. Prices are 2027 estimates and do not replace a written quote from a licensed plumber. Check current rules with Water Corporation, your local water provider and the Department of Water and Environmental Regulation before relying on anything here.

Reviewed by The Quote Yard Editorial Team

Published 19 November 2026 ·

How The Quote Yard Works

We connect you with independent local tradies and service providers, we don't perform any trade work ourselves. Tradies provide their own quotes directly to you. Always confirm licensing, insurance, and scope of work before engaging any provider.

Service availability may vary in regional WA. Verify licences at WA Building and Energy.
Prices are 2027 estimates for Western Australia and exclude new bore drilling, electrical work on pump outlets, turf and paving repairs and regional travel. Laboratory water tests and bore capping have no published band and are priced on quote.
Need work done? Get free quotes. Post a Job – It's Free