Old or Leaking Water Pipes?

Tell us the suburb or town, the year the house was built, whether it sits on a slab, how many bathrooms it has and what has gone wrong so far. We will put you in touch with licensed WA plumbers who can each price the same repipe or section replacement.

Get Free Repiping Quotes

Typical Costs (2027 Estimates)

Exposed pipe section replaced$300 - $700
Hidden section replaced in a wall$550 - $1,200
Underground service line repaired$850 - $2,500
Slab leak cut out and repaired$1,200 - $3,500
One wet area repiped$2,500 - $6,500
Full house repipe$8,500 - $25,000+
Plumber hourly rate, normal hours$110 - $165
Call-out and first hour$140 - $280

All figures are 2027 estimates for licensed work in Western Australia. Patching plasterboard, retiling, painting, Water Corporation fees and any leak search are extra unless the quote lists them.

Water Pipe Replacement Services WA - Get Local Quotes

Water pipe replacement covers everything from cutting out one corroded length behind a vanity to renewing every hot and cold line in the house. In Western Australia the reasons for the job can be local. Some homes built or renovated between mid-2017 and mid-2022 contain a grey polybutylene pipe, a type of flexible plastic pipe, that Building and Energy, the state regulator, has linked to leaks. Those homes are covered by a repair program run through their builders. Older homes may still have copper lines that stain basins blue-green or leak at pinholes. A leak in a wall cavity or under a slab can run unseen for weeks, and a water bill that rises without explanation may be the first sign. Mains pressure in parts of Perth can also run well above 500 kPa (kilopascals), the most allowed inside a building, unless a pressure reduction valve is fitted near the meter to lower it. In Water Corporation areas the owner pays for every pipe on the house side of the plumbers elbow, the bend in the pipe just past the meter, including the buried line to the house. Some homes only need one length replaced, while others need every line renewed through the ceiling. Leak searches, wall patching and painting should appear as separate items on a well written quote. Prices on this page are 2027 estimates for section repairs, wet area repipes and full house repipes. Post the job on The Quote Yard and we will connect you with licensed WA plumbers who can quote on it.

New Water Pipes for WA Homes

Repiping in WA can mean a single repair, a bathroom wing or the whole house, and the first step may be the pipe from the meter, high water pressure or a pipe product covered by a builder repair program. We can connect you with licensed plumbers from Perth to the regions who will all quote from the same written scope.

Get Free Quotes

At a Glance - Water Pipe Replacement Prices WA (2027 Estimates)

Job 2027 Estimate How It Is Priced What Moves the Price Paperwork
Exposed section replaced $300 - $700 Fixed Pipe size and reach Ask the plumber
Hidden section in a wall $550 - $1,200 Fixed or hourly Wall lining and tiles Ask the plumber
Slab leak cut out and repaired $1,200 - $3,500 After detection Floor covering and depth Ask the plumber
Meter to house line repaired $850 - $2,500 Fixed after locating Paving, rock and length Ask the plumber
One wet area repiped $2,500 - $6,500 Fixed after site visit Number of fixtures Major if routes change
Full house repipe $8,500 - $25,000+ Fixed after site visit Size, storeys, roof access Major if routes change
Hot water connection repaired $400 - $950 Fixed Valves and access Major if heater replaced
Pressure reduction valve Priced on quote Fixed Valve type and position Ask the plumber

What Changes a WA Repiping Price

Main cost drivers
Getting to the pipes takes much of the time. Ceiling routes need safe roof access, slab homes may need concrete cut, and service lines can run under driveways, paving and limestone.
The chosen pipe system also changes the price of the job. Copper, PE-X (a flexible plastic pipe) and multilayer systems each need their own fittings and tools, and the quote should name the system and its maker.
The paperwork a job needs depends on its scope. Like for like repairs to existing pipes count as minor work, while new routes, extensions and a new water heater make it major work, which needs advance notice and a signed certificate.
Repairing the walls and garden afterwards, known as making good, is a separate cost. Plasterboard patching, tiling, painting and restoring paving or lawn may be priced by other trades.
On a home built or renovated between mid-2017 and mid-2022, find out whether it has Typlex, a grey plastic pipe linked to leaks, before paying for a private repipe. Repairs for that product go through the builder first.

Replacing Water Pipes in Western Australian Homes

Water pipe replacement means removing the supply pipes that carry drinking water around a home and fitting new ones in their place. In WA the job ranges from a single section cut out of a wall to a full repipe, which renews every cold and hot water line in the house. Supply pipes are different from drains because they stay full of water under mains pressure all day and night. When one of them fails, it keeps leaking until someone turns off the water. For the wider range of household jobs a licensed plumber handles, see plumbing services across WA.

Some reasons for replacing pipes are particular to Western Australian homes. Homes built or renovated between mid-2017 and mid-2022 may contain a grey polybutylene pipe that the state regulator has linked to leaks, and those homes have their own repair program. Older homes may still have their original copper lines, and the WA Department of Health notes that corroding copper pipes can release copper into drinking water. Mains pressure in Perth can also sit well above the limit allowed inside a building when no pressure reduction valve is fitted. Each cause leads to a different first step, so the right answer depends on the house. Prices on this page are 2027 estimates taken from Quote Yard WA pricing pages, and they assume a licensed plumber does the work.

Replacing water pipes is licensed plumbing work in WA, apart from a short list of basic tasks the person living there may do. The plumber may also have paperwork to lodge, and that depends on whether the job counts as minor or major work. Adding a new pipe route or a new water heater changes the category, so ask about it before work starts. Keep any certificate of compliance with the house records, because it shows the new pipework was signed off.

What New Water Pipes Cost in WA (2027 Estimates)

Pipe replacement in WA is priced in a few broad ways, depending on how much is known before the plumber starts. Short exposed sections that are easy to reach are priced as a fixed job, at an estimated $300 to $700. Cutting into a wall to replace a hidden section costs more, with a 2027 band of $550 to $1,200 before any tiling or painting. Repiping one wet area, such as a bathroom or laundry, sits at $2,500 to $6,500, while a full house repipe runs from $8,500 to more than $25,000. These price ranges come from the WA figures on burst pipe repair costs and appear here as 2027 estimates.

Labour time is the other part of the bill when a job starts with a leak search. Licensed plumbers in WA charge around $110 to $165 an hour in normal hours, and a call-out with the first hour comes to $140 to $280. After hours and weekend call-outs cost $240 to $520 before any work begins. A hidden leak may need to be found first, and a search for a leak under the concrete slab alone costs $550 to $1,250. Searching an underground line between the meter and the house costs $650 to $1,500. Request the search and the replacement as separate lines so each can be compared.

When two full repipe quotes differ by thousands of dollars, compare the scope before the hourly rate. Each extra storey, bathroom, outdoor kitchen or long service line adds pipe, fittings and time. Some quotes include the hot water lines and outside taps, while others stop at the wet areas. Patching and painting may be priced, excluded or left vague, and that difference can be large. Each plumber should list the fixtures and outlets they will reconnect so the counts match.

Job 2027 Estimate How It Is Priced Notes
Exposed pipe section replaced $300 - $700 Fixed Under a sink, in a laundry or outside
Hidden section replaced in a wall $550 - $1,200 Fixed or hourly Patching and tiles extra
Slab leak cut out and repaired $1,200 - $3,500 Quoted after detection Floor coverings lifted and replaced
Underground service line repaired $850 - $2,500 Fixed after locating Meter to house, owner side
One wet area repiped $2,500 - $6,500 Fixed after site visit Bathroom, ensuite or laundry
Full house repipe $8,500 - $25,000+ Fixed after site visit Hot and cold lines to every fixture
Hot water connection repaired $400 - $950 Fixed Valves and fittings at the heater
New water service to the main, new home $1,800 - $4,000 Fixed Water Corporation fees separate
Slab leak detection $550 - $1,250 Fixed or hourly Before any concrete is cut
Pressure reduction valve fitted Priced on quote Fixed No WA band published

Grey Typlex Pipes in Homes Built 2017 to 2022

Building and Energy, the WA building and plumbing regulator, has reported water leaks in homes fitted with Pro-fit Typlex 1050 polybutylene pipe made by Iplex Australia. Polybutylene is a flexible plastic pipe material, and this product is grey with the words Iplex and Typlex printed along it. The affected homes were generally built or renovated between mid-2017 and mid-2022. Not every home from that period has the pipe, so the regulator advises owners to confirm with their builder. If you do not know who built the house, the local government can help with the building permit or plans. Owners in doubt should check before paying anyone to repipe.

Repairs to Typlex plumbing are now handled under the Industry Response, a repair agreement between the manufacturer, a group of builders and the WA Government. Under it, the builder has the first right to fix the problem, and owners are not expected to pay for the staged repair program. After a first failure, the builder repairs the pipe and replaces all of the pipes in the ceiling. A second failure brings a repair and, where the pipe is in a wall, an offer of a zone repipe covering that part of the house. Three or more failures bring an offer to replace all or part of the pipework, with temporary accommodation if the household needs it.

Every WA home with Typlex pipe is eligible for a free leak detection unit, whether or not a leak has happened. Owners register for the unit with the manufacturer, since the earlier government register has closed. Builders must repair failed external pipes and make good the surface, though they are not required to replace every external Typlex line. If a builder will not do the work, owners can lodge a building service complaint with Building and Energy on 1300 489 099. For Typlex failures that complaint can be made up to 15 years after practical completion, the date the finished home was handed over, compared with six years for other polybutylene pipe.

Before You Pay for a Private Repipe

Points from Building and Energy
Owners who pay for their own repairs are not reimbursed under the Industry Response.
A complaint may still lead to compensation where a builder was unable or unwilling to repair the pipes.
A settlement with the builder may stop a later complaint, depending on its terms.
Homes where all Typlex pipe has been removed, or fully settled by compensation, judgment or insurance, are excluded from the extended complaint period.
An insurance claim for a leak repair alone does not exclude a home.
Renters should report a leak to the landlord or property manager rather than booking a plumber themselves.

Get the builder's answer in writing before booking any private repipe on a Typlex home. Photographs of the printed pipe, the leak and the damage help both the builder and Building and Energy. If the builder disputes where the water is escaping, a plumber offering water leak detection in WA can mark the location before walls are opened. Keep every report and invoice, since a later complaint may rely on them.

Signs the Water Pipes Need Attention

The Water Corporation lists signs of a hidden leak, and the same signs can mean supply pipes are failing. They include a water bill that rises without explanation, and lawn or garden patches that are greener than the rest or feel spongy. Damp or discoloured patches on walls, ceilings or floors, and paint peeling or bubbling in a bathroom, kitchen or laundry, are on the list too. Running water heard when nothing is turned on, mould or musty smells, and a meter that keeps moving with every tap off complete it. Older houses are more likely to leak because of old plumbing, the Water Corporation adds, along with worn fittings and tree roots entering underground pipes. One sign alone does not prove the pipes need replacing, but several together justify a professional check.

Checking the water meter is the simplest first test at home. Turn off every tap and water-using appliance, then watch the meter for movement over a few minutes. Any movement while everything is off shows water flowing somewhere on the property. For a rough figure, the Water Corporation website has an online leak test that estimates how much water a leak is wasting.

Patching One Pipe or Repiping a Zone or the Whole House

One leak at a fitting does not always mean the rest of the pipework is failing. Plumbers judge this from the age and material of the pipes, how many leaks the house has had and what a cut-out section looks like inside. A repair that keeps the existing pipe suits a one-off failure caused by a nail, a crushed pipe or a single faulty joint. Repeated leaks in the same material, or pitting and staining on cut sections, suggest that more than one length needs replacing. Request the removed section so you can see the inside for yourself.

Zone repiping replaces every pipe in one part of the house, such as the bathroom wing or the kitchen and laundry. It costs less than a full repipe and keeps other rooms working while one area is done. Full repiping makes sense when leaks are spread across the house, when the pipe material itself is the problem or when a renovation has walls open anyway. Linking the job to a renovation saves opening and patching the same walls twice, and bathroom renovation plumbing can be priced on the same visit. For a burst that needs attention tonight, start with burst pipe repairs and plan the larger job afterwards. An emergency visit is aimed at restoring water, not at reviewing the whole system.

The Pipe on Your Side of the Water Corporation Meter

The Water Corporation draws its line of responsibility at the plumbers elbow, the bend in the pipe on the house side of the water meter. For a single detached house, leaks between that elbow and the house are the owner's to repair, while leaks between the elbow and the street are the Water Corporation's. Units and shared buildings with sub-meters, which are separate meters for each home, follow a different split, so check the Water Corporation leaking meter diagrams first. On an above-ground meter, the plumbers bend, as the elbow is also called, sits at least 100 to 150 mm above finished ground level. If the leak is on your side, the Water Corporation says to engage a licensed plumber. If it is on its side, or you cannot tell, call its 24-hour faults line on 13 13 75.

The service line from the meter to the house can be the oldest pipe on the property and the hardest to reach. In older homes it may run under driveways, paving or garden beds, and its route is not always on any plan. Replacing it means digging a new trench or drilling a tunnel under hard surfaces, and the 2027 estimate for an underground service line repair is $850 to $2,500. Brand new water services to the street main cost $1,800 to $4,000, with Water Corporation fees charged separately. Owners planning a new build can compare that work on new home plumbing in WA.

Moving the meter is sometimes part of a service line replacement, for example when a new driveway would sit over it. The owner applies to the Water Corporation and pays its relocation fees, and a licensed plumber moves the pipework on the property side. The plumber also fits a temporary service line so the house keeps water until the meter moves. Relocation of the meter by the Water Corporation then follows within 10 working days of the application coming off hold. Keep 300 mm clear around the meter and 1,200 mm clear above it, because the Water Corporation needs safe access to read and replace it.

Homes in the City of Bunbury and surrounding areas get their water from Aqwest, and homes around Busselton are supplied by Busselton Water. Both suppliers publish their own leak and fault information, so check their rules before assuming the Water Corporation boundary applies. Busselton Water lists a 24-hour emergency number of 08 9781 0500 on its home page. Local plumbers for these towns are listed on hiring a plumber in Bunbury and the South West.

Water Bills, Hidden Leaks and the Leak Allowance

Failing pipes under a slab or in the garden can run up a large water bill before anyone sees damp. The Water Corporation offers a leak allowance, a partial credit on the bill, for hidden leaks that were not readily detectable. To qualify, the leak must be repaired within 60 days of being found or of the Water Corporation telling you about it. The recent bill must show a water use charge over $250 or use above 150 kL, where one kL is 1,000 litres. You apply within six months of the repair date, with a copy of the tax invoice from the licensed plumber who fixed it. Visible leaks at taps, shower heads and toilet cisterns are excluded, as are pools, spas and water features.

The allowance is one more reason to keep every invoice and to make sure it names the repair clearly. Invoices that only say plumbing labour may not show that a hidden leak was found and fixed. The invoice should describe the location, the pipe material and the repair. Search costs before any repair are listed on water leak detection costs in WA, which helps when budgeting for both steps.

Eligible hidden leak repairs may earn an allowance of up to 50 per cent of the estimated water lost, according to the Water Corporation. Irrigation leaks may be repaired by a Waterwise Garden Irrigator, an irrigation installer endorsed by the Water Corporation, for the allowance, but pipes inside the house need a licensed plumber. Irrigation leaks can be excluded if the system lacks a manual isolation valve, a hand-turned shut-off tap, and a master solenoid, the electric valve that shuts off the whole system. Arranging the repair is the owner's job, because the Water Corporation states that leak repairs are the property owner's responsibility.

Mains Pressure, the 500 kPa Limit and Reduction Valves

Water pressure is measured in kilopascals (kPa) or in metres head, the height of a column of water the pressure could hold up. The Water Corporation supplies a standard range of 15 to 100 metres head in the Perth metropolitan area, and 13 to 100 metres head in regional areas. One metre head equals roughly 10 kPa, so 100 metres head works out at about 1,000 kPa. Inside a building, the Australian plumbing standard AS/NZS 3500.1:2025 clause 3.3.4 sets a maximum of 500 kPa, according to a Building and Energy technical note. The same standard sets a minimum of 50 kPa at outlets so taps still run properly. A home at the top of the supply range can therefore receive about double the pressure allowed indoors.

High pressure matters for new pipes because the Water Corporation states that it can increase the occurrence of leaks and bursts. It can also shorten the life of appliances and fixtures and make pipes noisy. A pressure reduction valve is a spring-loaded valve fitted near the meter that lowers the pressure for every pipe and fitting after it. Such a valve can hold pressure steady at up to 50 metres head, the Water Corporation notes. No WA pricing page gives a figure for fitting one, so it is priced on quote.

Braided flexible hoses, the woven metal hoses that join taps, toilets and appliances to the wall pipes, also need attention during a repipe. High or fluctuating pressure, such as water hammer, can harm them, according to a Building and Energy technical note. Water hammer is the bang heard in pipes when a tap or appliance valve shuts quickly. The note says hoses must stay accessible and above ground, never buried, with an isolation valve, a small shut-off valve, fitted immediately before each hose. Check whether the quote replaces the hoses at each fixture or reuses the old ones.

Australian Valve Group makes the PRVB boundary pressure reduction valve, which it sets to 500 kPa for domestic dwellings. RWC makes the RMC range of combination non-return and isolating valves and backflow preventers, which stop water flowing back the wrong way and are fitted near meters and appliances. Before quoting, the plumber can measure static pressure, the pressure with every tap closed, at an outside tap and write the reading on the quote. If a valve is already fitted, the reading shows whether it still works. A garden sprinkler system, called reticulation in WA, connected to scheme water may need its own backflow device, and a bore and reticulation plumber can check that at the same visit. Fixing pressure first protects the new pipes from the problem that may have damaged the old ones.

Copper, PE-X and Other Pipe Choices for WA Homes

New water pipes in WA homes are mostly copper or one of several plastic systems, and each joins in a different way. Copper is a rigid metal pipe joined by soldering or by press fittings, which are fittings squeezed onto the pipe with a powered tool. PE-X is cross-linked polyethylene, a flexible plastic pipe that bends around corners and needs fewer joints. Multilayer pipe has a thin aluminium layer between plastic layers, so it holds its shape once bent. Each system has its own fittings, and they should not be mixed unless the maker approves it. Expect the quote to name the system and the maker.

Viega makes Propress, a copper press fitting system, and Sanpress Inox, a stainless steel press system. REHAU makes RAUTITAN, a PE-Xa pipe system, PE-Xa being one type of PE-X, joined by pressing a sleeve over the pipe and fitting. It also sells a Lead-Free RAUTITAN range for drinking water lines. Either can be quoted by name, and the pipe and fittings must come from the same system. Owner duties listed by the Water Corporation include using WaterMark or Standards Mark approved pipe, fittings and fixtures, and WaterMark is the national certification mark for plumbing products. Check that the quote names a certified system and not unbranded fittings.

The WA new home plumbing guide on The Quote Yard lists PE-X for supply pipe above the slab and copper for uses that need rigidity or heat resistance. No WA pricing page publishes a per metre price for copper or PE-X, so compare whole quotes for the same layout. Fewer joints inside a wall cavity also mean fewer places where a future leak can start. On a Typlex home, make sure the replacement pipe is a named system with a maker's warranty you can read.

Ceilings, Slabs and Sandy Ground: Where New Pipes Run

In a house built on a concrete slab, supply pipes run through the slab, inside the walls or across the ceiling space. Replacing pipe inside a slab means cutting concrete and floor coverings, which is why a slab leak repair has a 2027 band of $1,200 to $3,500. Running new pipe across the ceiling and down inside the walls avoids the slab entirely. The trade-off is more openings in plasterboard, plus work in a hot roof space that needs safe access. Plumbers can follow a Building and Energy technical note on the support and fixing of pipework, so ask how the new lines will be clipped. Mark the planned wall openings on a floor plan before work begins.

Underground service lines raise a different set of problems from pipes inside the house. Sand is quick to dig but trench sides can slump, and limestone or granite slows any excavator down. Before digging, a request through Before You Dig Australia (BYDA) gives one place to ask for information about underground and overhead infrastructure at the site. Longer runs may suit a separate contractor, and excavation services in WA can quote the trench while the plumber quotes the pipe. Restoring paving, reticulation and lawn should be listed as included or excluded on the quote.

Minor Work, Major Work and the Certificate of Compliance

Only people holding plumbers licences granted by the Plumbers Licensing Board may carry out plumbing work in WA. Building and Energy, part of the Department of Local Government, Industry Regulation and Safety, regulates the industry alongside the board. Occupiers may do a short list of tasks themselves, such as replacing a shower head, repairing a tap other than a thermostatic mixing tap, which sets the water temperature itself, and replacing a cistern washer. Changing a water filter cartridge and clearing a blocked fixture with a plunger are also on that list, while a toilet the plunger cannot clear needs blocked toilet repair services. All other water supply, sanitary and drainage plumbing, covering clean water in and waste water out, needs a licensed plumber or permit holder. You can check a plumber on the Online Licence Search run by Building and Energy, and advertising as a plumber without a licence is an offence.

WA rules split plumbing jobs into two groups called minor work and major work. Minor work includes the testing, maintenance, repair or replacement of existing water supply plumbing. Major work covers installations and alterations that are not minor, and replacing a water heater or a testable backflow device, which stops used water flowing back into the mains, is always major. For major work, the contractor gives the Plumbers Licensing Board a notice of intention at least 24 hours before starting. A certificate of compliance, a signed statement that the work meets the plumbing standards, follows within five working days of finishing. Emergency work is exempt from the advance notice, and both documents can then be lodged together within five working days.

Situation Category Before Work After Work
Leaking length replaced like for like Minor work No notice Contractor keeps records
New pipe routes or extensions Major work Notice of intention, 24 hours ahead Certificate within five working days
Water heater replaced during a repipe Major work, always Notice of intention Certificate within five working days
Testable backflow device fitted Major work, always Notice of intention Certificate within five working days
Emergency repair to restore supply Exempt from advance notice None Notice and certificate together within five working days

For major work, the homeowner should receive the certificate of compliance within five working days of completion. Building and Energy describes it as your six-year guarantee that the work meets the plumbing standards. Whether a repipe is minor or major depends on whether new pipes simply replace existing ones or take new routes and connect a new water heater. Ask the plumber to state the category on the quote and to send the certificate once the job is done.

Rural homes that drink tank or bore water are not outside the rules either. Building and Energy announced that regulation of plumbing work on unmetered drinking water supplies was due to start on 10 February 2025. Repiping a property fed from a tank or bore for drinking water is therefore licensed plumbing work. Get written confirmation of how the notice and certificate rules apply to that supply.

Pressure Testing and Flushing Before Walls Close

New water pipes must be tested before they are buried or covered. A Building and Energy technical note states that water services shall show no leakage under a hydrostatic pressure of 1,500 kPa for at least 30 minutes. Hydrostatic means the test uses water held under pressure in the pipes, with a gauge showing any drop. For plastic pipes the gauge may settle to a lower reading, such as 1,250 kPa, and the test passes if no leaks appear after 30 minutes. Ask to see the gauge reading, or a photograph of it, before the plasterer closes the wall.

After testing, the note requires the pipework to be flushed thoroughly until the water runs completely clear. Flushing removes sand, cutting debris and anything else left in the new lines. The plumber then checks taps, valves and cisterns so that no air stays trapped in the system. Puretec makes the FILTERWALL F Series, a whole house filter system that reduces sediment and chlorine, for owners who want filtered water at every tap. Where the house has a fridge water line or an under-sink filter, ask for it to be reconnected and checked, or book water filter and fridge line installation separately. Keep the test details with the certificate of compliance for later reference.

Copper in Drinking Water and the First Flush

Copper pipes are one reason owners ask about replacement, especially when basins and showers show blue-green marks. The WA Department of Health says the main cause of higher copper levels is water left standing in household copper pipes for long periods. Corroding copper pipes can also release copper into drinking water. A low level of copper leaves a green or blue stain on taps, basins, showers or toilets, and that water is still safe to drink. Metallic or bitter tastes suggest a high level, and that water may not be safe. The department advises letting the first 30 seconds of water run to waste, using it on the garden or to flush the toilet.

The Australian Drinking Water Guidelines set 1 milligram per litre (mg/L) for taste and staining and 2 mg/L to prevent health problems, according to the WA Department of Health. If the taste suggests a high level, the department suggests contacting the drinking water provider or having the water tested. Staining alone does not prove that pipes need replacing, so test first if water quality is the main worry. From there, a plumber can judge whether a section, a zone or the whole house is involved.

The first flush advice is simple to follow after a repipe as well. Holiday homes and houses left empty for weeks hold water in the pipes for long periods, which the department names as the main cause of higher copper levels. Running each tap briefly on return clears the water that has been sitting in the lines. Water from that first flush can go on the garden instead of down the drain. Plumbers fitting new pipes should also flush the whole system at handover, as the technical note requires.

Hot Water Lines and Temperature Control Devices

Hot water pipes carry heat as well as pressure, and a repipe that skips them leaves the older material in place. Replacing the water heater during the same job is always major work in WA, which means a notice of intention and a certificate of compliance. Since 1 May 2024, a temperature control device must be fitted when a water heater is replaced in an existing installation used for personal hygiene, such as showers and basins. A thermostatic mixing valve is one such device, blending hot and cold water so the outlet never runs hotter than a set temperature. Enware makes Aquablend thermostatic mixing valves, and RWC makes thermostatic mixing valves under its RMC brand.

If the old water heater is near the end of its life, replacing it while the pipes are being changed avoids a second visit. Rheem makes gas storage, continuous flow, electric, heat pump and solar water heaters. Rinnai makes gas continuous flow units and the Enviroflo heat pump range. On its own, a hot water connection repair has a 2027 band of $400 to $950. For unit choices and prices, see hot water system installation in WA, and keep the heater and pipe work on one quote if both happen together.

Patching Walls, Ceilings and Tiles After the Plumber

Some repipe quotes cover only the plumbing and leave the openings for someone else, so check who closes them. Plasterboard openings need patching, coating with plaster compound and sanding before any painting. CSR makes Gyprock plasterboard, with Plus, Supaceil and Aquachek among its residential boards. Selleys makes Spakfilla Rapid for small holes and a wet area silicone sealant for joints around fixtures. Dulux makes Wash&Wear interior paint and Ceiling White for the final coats. After the plumber leaves, a tradesperson from plastering and Gyprock repairs can match the wall finish.

Tiled walls in wet areas raise the cost of making good, because a tile cut out to reach a pipe may not have a matching spare. ARDEX makes tile adhesives, cement-based and epoxy grouts, and internal undertile waterproofing membranes. If an opening in a shower wall cuts through the waterproofing membrane, the membrane needs repair before tiles go back, or water can reach the framing. Keep a few spare tiles from any renovation for this reason, and photograph the wall before it is opened. When the plumber does not tile, get a separate quote for bathroom tiling in WA.

Outside the house, a new service line leaves a trench across lawn, garden beds or paving. Reticulation pipes and sprinklers in the trench path may need cutting and rejoining, so ask whether the plumber includes this. Pavers can be lifted and stacked before digging so they can be relaid instead of replaced. Confirm who will compact the sand under relaid paving so the surface stays level. Photograph the garden and paving before work starts so any damage can be checked against the original.

Living in the House While the Pipes Change Over

A staged repipe lets the household keep water in some rooms while others are worked on. The plumber can install new lines alongside the old ones and switch fixtures over one at a time, so the water is off for shorter periods. Ask for a written plan showing which days each bathroom, the kitchen and the laundry will be out of action. Households with babies or people needing care at home should mention this when asking for quotes. Even so, a short shutdown at the main stop tap may be needed to connect the new main line.

Furniture near the walls being opened should be moved, and floors covered against plaster dust. Ceiling work means the plumber needs safe access to the roof space, so clear the area under the ceiling access hatch. Keep pets away from open trenches and from work areas where tools and offcuts are lying around. Clearing a path from the street to the meter also saves time on the first day.

Perth Suburbs and Regional WA

Across the Perth metropolitan area, repiping quotes vary with the age of the house, the floor type and the roof access. Homes in older suburbs may have long underground service lines that have never been replaced. Plumbers serving the city are listed on hiring a plumber in Perth, and the hills and valley suburbs have their own page for plumbers in the Swan Valley and Perth Hills. Rural blocks in the hills may rely on tanks or bores, which changes the pressure and the pipe sizes needed. Tell plumbers which supply the house uses when asking for a price.

In regional towns, travel time can add more to a repipe quote than the hourly rate shows. Plumbers in the south of the state are listed on hiring a plumber in Albany and the Great Southern. Coastal homes south of Perth can call on plumbers in Mandurah and the Peel. Find out whether travel is charged per visit or once for the job, since a staged repipe may need several trips. Rural homes with a septic system can pair the pipe job with septic tank services if the same business does both. Agree a written start date early in towns served by only a few licensed plumbers.

Landlords, Tenants and Strata Lots

Consumer Protection has published guidance for landlords whose rental homes have Typlex pipes. Landlords should tell the property manager about the pipes and any leak detection unit before the property is advertised, and record them in the property condition report. Tenants are told to check water bills for unusual increases and to report a leak to the landlord or property manager as soon as possible. Planned repair work that could affect the tenancy should be disclosed to tenants in writing. For urgent repairs and entry rules, the guidance refers readers to the Residential Tenancies Act 1987 and to Consumer Protection on 1300 30 40 54.

In strata buildings, some water pipes may be common property, owned jointly and managed by the strata company that all owners belong to, while others belong to a single lot. Before booking a repipe, confirm with the strata company which pipes it is responsible for, and get its approval in writing for work in shared walls or ceilings. Work that touches common property may need to be organised by the strata company and not by the lot owner. Plumbers who handle strata plumbing can work with the strata manager where a building has shared pipes.

Contracts, Deposits and Complaints in WA

Consumer Protection says a quote is a total price that forms a binding contract once accepted, while an estimate is approximate and can change. It suggests getting at least three written quotes before agreeing to the work. For trade jobs, it advises paying only a small deposit of no more than 10 per cent of the total price. Builders may not ask for more than 6.5 per cent on building contracts valued between $7,500 and $500,000. Pay instalments as the work is done, following the quote terms, and never the full amount before the job is complete. Where a builder runs the repipe as part of a renovation, the work may fall under the building contract instead of a separate plumbing quote.

Problems with the standard of plumbing should go to the plumber in writing first, since Building and Energy expects that step before a complaint. Plumbing complaints about work completed within the last six years can then be lodged with Building and Energy. If fixing the plumbing could cause damage to the building, a building service complaint is lodged instead. Disputes about the contract or money go to Consumer Protection, not the plumbing complaint form. Keep the quote, invoices, certificate of compliance and photographs together for any later complaint.

What to Look Out For in a WA Repiping Quote

Every repipe quote should name the pipe system and its maker, the number of fixtures connected and the route the new lines will take. It should say whether the hot water lines are included and whether the water heater is being replaced. Making good should be listed line by line, separating plasterboard, tiles, paint and any paving or lawn. Check that pressure testing and flushing are listed, along with a static pressure reading and any reduction valve. The quote should also state whether the job is minor or major work and who lodges the paperwork.

Watch for a full repipe recommended after a single leak with no evidence shown. On a home built between mid-2017 and mid-2022, be wary of any quote that skips the question of Typlex pipe and the builder's role. Prices far below the others may leave out patching, the ceiling route or the certificate of compliance. Ask for the licence number and check it on the Online Licence Search before paying a deposit.

Items to Find on Every Quote

What a complete quote shows
Pipe system and maker named, with the warranty period.
Every fixture, outdoor tap and appliance connection listed.
Route described, with ceiling, wall and slab sections shown.
Static pressure reading and any pressure reduction valve.
Pressure test, flushing and final checks of every tap and valve included in the price.
Minor or major work stated, and the certificate of compliance confirmed for major work.
Plasterboard, tiling, painting and outdoor restoration included or excluded in writing.
Compare what each quote includes before comparing the totals. A low total on a repipe can hide missing patching, a shorter route or no certificate.

Getting Repiping Quotes That Compare Fairly

Give every plumber the same written description so their prices line up. Include the suburb or town, the year the house was built, slab or timber floor, the number of bathrooms, and where the meter and water heater are. Add photographs of any leak, the meter, the hot water label and any cut section that was removed. Say whether the house was built or renovated between mid-2017 and mid-2022, and whether the builder has been contacted. Call-out and hourly rates to compare against are listed in the WA plumber pricing guide.

Timing and certainty matter on a repipe as much as the total price. Find out how long each price holds, how soon the plumber can start and how many days the house will be affected. Plumbers who have seen inside the ceiling and walls can give a firmer price than those quoting from photographs. Where access is unknown, ask for a written allowance for extra time and the hourly rate it will be charged at.

Buyers can ask for a plumbing check before settlement to avoid inheriting a failing water service. Booking a pre-purchase plumbing inspection lets a plumber identify the pipe material, test the static pressure and look for signs of past leaks. That information helps when negotiating, or when planning a repipe after moving in. Owners chasing a water bill they cannot explain should start with a leak search before asking for repipe quotes. Once the source is known, the repair or replacement can be priced on facts. If water is spraying now, turn off the main stop tap and book an emergency plumber before planning anything larger.

Water Pipe Replacement Across Western Australia

The 2027 estimates on this page apply across Western Australia. Homes close to Perth and the regional centres seldom pay a travel charge, while farms and outlying towns may pay for each trip a staged repipe needs.

▶ Perth 28 areas
Perth CBD Joondalup Wanneroo Butler Alkimos Stirling Scarborough Hillarys Karrinyup Morley Bayswater Bassendean Belmont Victoria Park South Perth Melville Applecross Canning Vale Willetton Cannington Fremantle Cockburn Rockingham Baldivis Gosnells Armadale Byford Ellenbrook
▶ Mandurah & Peel 20 areas
Mandurah Halls Head Dawesville Falcon Erskine Silver Sands Madora Bay San Remo Greenfields Meadow Springs Lakelands Coodanup Pinjarra Ravenswood Waroona Dwellingup North Dandalup Serpentine Jarrahdale Boddington
▶ Bunbury & South West 24 areas
Bunbury Australind Eaton Dalyellup Gelorup Capel Busselton Vasse Dunsborough Yallingup Margaret River Cowaramup Augusta Harvey Brunswick Junction Collie Donnybrook Balingup Nannup Bridgetown Boyup Brook Manjimup Pemberton Northcliffe
▶ Swan Valley & Perth Hills 24 areas
Guildford Midland Herne Hill Middle Swan West Swan Upper Swan Caversham Baskerville Henley Brook Swan View Helena Valley Kalamunda Gooseberry Hill Lesmurdie Walliston Carmel Pickering Brook Mundaring Glen Forrest Darlington Parkerville Chidlow Roleystone Bedfordale
▶ Avon Valley & Wheatbelt 22 areas
Northam York Toodyay Beverley Bakers Hill Clackline Wundowie Goomalling Dowerin Wongan Hills Cunderdin Tammin Kellerberrin Merredin Wyalkatchem Trayning Nungarin Quairading Brookton Corrigin Bruce Rock Narrogin

Water Pipe Replacement FAQ - WA

How much does it cost to repipe a house in WA?
Full house repipes in WA have a 2027 estimate of $8,500 to more than $25,000, depending on size, storeys and roof access. Repiping one wet area such as a bathroom costs $2,500 to $6,500. Replacing a single hidden section in a wall costs $550 to $1,200, and an exposed section costs $300 to $700. Patching walls, tiling, painting and any leak search are extra unless a quote lists them, so check what each quote includes. The WA plumber hourly rate of $110 to $165 applies to any work charged by the hour.
How do I know if my home has Typlex pipes?
Building and Energy describes the product as grey pipe with Iplex and Typlex printed along it. Affected homes were generally built or renovated between mid-2017 and mid-2022, but not every home from that period has it. Start with your builder, and if you do not know who built the house, the local government can help with the building permit or plans. Every home with Typlex pipe is eligible for a free leak detection unit from the manufacturer.
Should I pay for my own repipe if my home has Typlex pipe?
Contact your builder first, because the builder has the first right to fix Typlex failures under the Industry Response. Owners are not expected to pay for that repair program, and owners who pay privately are not reimbursed under it. Where the builder will not act, you can lodge a building service complaint with Building and Energy on 1300 489 099. For Typlex failures, that complaint can be lodged up to 15 years after practical completion. Renters should contact their landlord or property manager instead of arranging repairs themselves.
Who fixes the pipe between the water meter and my house?
For a single detached house, the Water Corporation is responsible from the street to the plumbers elbow, the bend in the pipe just past the meter. Leaks between the plumbers elbow and the house are the owner's responsibility and need a licensed plumber. Units with sub-meters follow a different split, shown in the Water Corporation leaking meter guidance. If you are unsure which side the leak is on, call the Water Corporation faults line on 13 13 75.
Does replacing water pipes need a certificate of compliance in WA?
It depends on whether the job is minor or major work under WA rules. Replacing existing water supply plumbing is minor work, while new installations, alterations and any water heater replacement are major work. Major work needs a notice of intention at least 24 hours before it starts and a certificate of compliance within five working days of finishing. The homeowner should receive the certificate, which Building and Energy calls a six-year guarantee for the work.
What water pressure is allowed inside a WA home?
AS/NZS 3500.1:2025 clause 3.3.4 sets a maximum of 500 kPa within a building, as cited in a Building and Energy technical note. The Water Corporation supplies 15 to 100 metres head in Perth, and 100 metres head is roughly 1,000 kPa. Fitting a pressure reduction valve near the meter brings the pressure down for the whole property. Have the plumber measure the static pressure before new pipes go in, and price a valve if it is needed.
Can I get a credit on my water bill after a hidden leak?
The Water Corporation leak allowance can apply to hidden leaks that were not readily detectable. The leak must be repaired within 60 days, and the recent bill must show a water use charge over $250 or use above 150 kL. You apply within six months of the repair with a tax invoice from the licensed plumber. Visible leaks at taps, toilet cisterns and shower heads are excluded, as are pools and spas.
Which pipe material should I choose for a repipe?
Copper and cross-linked polyethylene, known as PE-X, are both used for water supply in WA homes. Copper is rigid and joined by soldering or press fittings, while PE-X is flexible and needs fewer joints. Whichever you choose, the pipe and fittings should come from one named system with WaterMark certification. Each plumber should name the system and maker so the quotes can be compared on the same basis.
Will we be without water for days during a repipe?
A staged repipe keeps water running in parts of the house while other rooms are worked on. New lines can be run beside the old ones and each fixture switched over in turn, which keeps shutdowns short. Even then, a brief shutdown at the main stop tap may be needed when the new main line is connected. Request a written plan showing which rooms are out of action on which days.
Do blue-green stains mean my copper pipes need replacing?
Not on their own, according to the WA Department of Health, which says low copper levels cause green or blue staining and the water is still safe to drink. Metallic or bitter tastes suggest a higher level that may not be safe. The department advises running the first 30 seconds of water to waste and contacting the drinking water provider or testing if taste is a concern. A plumber can then check whether the pipes themselves are corroding. Staining from low copper levels is mainly a cleaning problem, while a bad taste deserves a test.

Trades for Pipe Replacement Jobs

For Trades & Contractors - WA

Plumbers who repipe homes and replace water services in WA can find current work on the WA job leads board, along with plumber jobs in WA and leak detection jobs.

Compare WA Repiping Quotes

Describe the house, the pipes and the leaks so far, and compare quotes from licensed Western Australian plumbers who are all pricing the same repair or repipe.

Get Free Repiping Quotes

About This Guide

This page provides guidance information only. Details may change, always verify with the relevant authorities and seek independent professional advice where needed.

Reviewed by The Quote Yard Editorial Team

Published 19 November 2026 ·

How The Quote Yard Works

We connect you with independent local tradies and service providers, we don't perform any trade work ourselves. Tradies provide their own quotes directly to you. Always confirm licensing, insurance, and scope of work before engaging any provider.

Service availability may vary in regional WA. Verify licences at WA Building and Energy.
Prices are 2027 estimates for licensed water pipe work in Western Australia. They exclude plasterboard, tiling and painting repairs, Water Corporation fees and leak searches unless a quote lists them.
Need work done? Get free quotes. Post a Job – It's Free