Old or Leaking Water Pipes?
Tell us about the pipes, the leaks or rusty water you have noticed and the age of the home, and we'll connect you with licensed plumbers near you.
Typical Costs (2027 Estimates)
These figures are 2027 estimates for NSW homes. Trenching per metre, plaster patching, painting and paving repairs are priced per job.
Water Pipe Replacement Services NSW - Get Local Quotes
Water pipe replacement in NSW means swapping worn supply pipes for new ones, from a single corroded length under the kitchen to a full repipe from the water meter to every tap. Older homes may still have galvanised steel pipe, which rusts from the inside, while others have ageing copper or plastic pipe with joints that slowly leak inside walls. A licensed plumber can identify what you have, check its condition and tell you whether one section will do or the whole system needs replacing. New pipes are copper or plastic systems approved for drinking water, and the plumber should explain why one suits your home. Price depends on pipe length, access through walls, roofs and floors, and whether a trench is needed between the meter and the house. Making good, the repair of plaster, tiles and paving after the work, can add to the bill. Using 2027 estimates for NSW, one section costs about $350 to $800, and a full repipe of a three-bedroom house $3,000 to $15,000. Staged replacement, one area at a time, can spread the cost of a full repipe. Sydney Water owns the water main in the street and the meter, while owners look after the pipes on their side. Before digging a trench for a buried pipe, the plumber should lodge a Before You Dig Australia enquiry. Plumbing work needs a licence in NSW, and larger jobs come with a Certificate of Compliance, a signed record that the work meets the rules, and a written contract above $5,000. Knowing the pipe material and the likely routes before you call helps each plumber quote the same job.
At a Glance - Water Pipe Replacement in NSW (2027 Estimates)
| Job | 2027 Estimate (NSW) | Suits | Disruption | Paperwork to Keep |
|---|---|---|---|---|
| Pipe section replacement | $350-$800 | One damaged length in otherwise sound pipes | Hours, one area | Tax invoice |
| Concealed pipe repair | $400-$1,500+ | Leak inside a wall or floor | Wall or floor opened | Tax invoice and photos |
| Ceiling pipe repair | $450-$1,000 | Leak above a ceiling | Ceiling patch needed | Tax invoice |
| Underground water service repair | $800-$5,000 | Meter to house pipe failing | Trench across the yard | Certificate of Compliance |
| Pipe repair under a slab | $1,200-$8,000 | Leak in pipe set in a concrete floor | Floor cut or pipe rerouted | Certificate of Compliance |
| Supply pipe condition inspection | $300-$600 | Deciding whether to replace | Short visit | Written findings |
| Pressure limiting valve, fitted | $200-$600 | Street water pressure above 500 kPa | Short shut-off | Invoice with valve setting |
| Full repipe, three-bedroom house | $3,000-$15,000 | Galvanised steel or failing pipe throughout | Several days, staged shut-offs | Written contract and Certificate of Compliance |
Cost Depth: Why Pipe Replacement Prices Spread So Far
Length of pipe is only part of the price, and access decides much of the rest. Replacing a single section of pipe costs an estimated $350 to $800, while concealed pipe in a wall or floor costs $400 to $1,500 or more because the surface has to be opened and repaired.
Pipes buried in the yard or set in a concrete floor cost the most to repair. An underground water service repair is estimated at $800 to $5,000, and a full repipe of a three-bedroom house at $3,000 to $15,000, depending on storeys, floor type and where the pipes run.
All figures are 2027 estimates for NSW. Plastering, painting, paving and regional travel can add to the final amount.
When Replacing Water Pipes Beats Another Repair
Water supply pipes carry drinking water under pressure from the meter to every tap, toilet, shower and appliance in the home. They differ from drain pipes, which carry used water away at low pressure, so a slow sink or a blocked toilet is a separate job. If water backs up in a basin or the kitchen sink, start with our guide to blocked sink and basin repairs instead. Supply pipes wear out slowly, and the first signs can be small, such as a slowly dripping joint or a brown stain on a ceiling. Replacement becomes the sensible choice once repairs keep coming back or the pipe itself is failing along its length.
One leak on an otherwise sound pipe can be cut out and joined with new fittings in a single visit. Repeated leaks, rusty water, falling flow and pipe that crumbles when handled suggest the material is reaching the end of its life. Patching one weak spot on such a pipe can shift the strain to the next joint along, so the leaks move instead of stopping. If a section is cut out, keep it and look inside, since the inside of the old pipe shows how far corrosion has gone.
Timing matters as much as condition, because pipe work is easiest when walls and floors are already open. Renovating a kitchen or bathroom is a natural moment to renew the pipes in that room, even if they have not yet leaked. Extensions are another trigger, since a new bathroom adds demand that an old, narrow service pipe, the pipe from the meter to the house, may not meet. Buyers who find old pipes during a purchase can plan the work before moving in, while the house is still empty. Repeated urgent visits add up too, with after-hours labour estimated at $150 to $250 an hour each time. Weighing those repeat costs against a planned replacement helps you decide when to stop patching.
Water Pipe Replacement Prices for 2027
Pipe replacement is priced job by job, but the bands below give NSW households a guide to likely costs. A business-hours call-out fee, the charge for coming to your home, is estimated at $80 to $150, and hourly labour at $90 to $180. Plumbers commonly charge at least one hour of labour, according to our NSW pricing pages, so a brief visit may still be billed as a full hour. Every figure here is a 2027 estimate drawn from Quote Yard NSW plumbing pages, and the final price can move once walls or ground are opened. Materials are commonly marked up 10 to 30 percent over the trade price the plumber pays, so check whether pipe and fittings appear as separate lines on the quote.
| Job | 2027 Estimate (NSW) | What Drives the Price |
|---|---|---|
| Simple exposed pipe repair (screw-on compression fitting) | $150-$300 | Pipe material and fitting type |
| Pipe section replacement (one length) | $350-$800 | Length of run and access |
| Flexible plastic (PE-X) pipe repair | $200-$450 | Fitting system and access |
| Ceiling pipe repair | $450-$1,000 | Ceiling access and patching |
| Concealed pipe repair in a wall or floor | $400-$1,500+ | Wall, floor and tile access |
| Underground water service repair | $800-$5,000 | Trench length, depth and surface |
| Pipe repair under a concrete slab | $1,200-$8,000 | Slab cutting or rerouting |
| Supply pipe condition inspection | $300-$600 | Size of home and pipe access |
| Pressure limiting valve, fitted | $200-$600 | Valve size and position |
| Isolation (shut-off) valve replacement | $100-$220 | Number of valves and access |
| Full repipe, three-bedroom house | $3,000-$15,000 | Storeys, floor type and routes |
The full repipe band is wide because Quote Yard pages give different figures, from $3,000 to $8,000 on one and $8,000 to $15,000 on another. Single-storey houses with a timber floor and open roof space are usually toward the lower end, since pipes can run where they are easy to reach. Two storeys, a concrete slab, tiled walls or a long trench to the meter all push the price toward the upper end. Our pages publish no figures for trenching per metre, plaster patching or painting, so ask for those items in writing.
Combining bands gives a rough total, though the quote a plumber gives after seeing the pipes is what counts. Suppose a plumber replaces a corroded pipe under the kitchen and fits a new isolation valve, a small tap that shuts off one fixture, at the sink. The pipe is estimated at $350 to $800 and the valve at $100 to $220, giving $450 to $1,020 before any separate call-out fee. Adding a call-out fee of $80 to $150 brings the total to between $530 and $1,170. You can compare state-wide call-out and hourly rates in our NSW plumber pricing guide.
Read each quote for what is and is not included in the price. Some plumbers include disposal of the old pipe, inspection fees and the Certificate of Compliance, while others list them as extras. Goods and services tax should be shown clearly, so you can tell whether two prices are on the same basis. Making good, such as patching plaster and relaying pavers, is an item to check closely on every quote. Hidden damage found once walls are open, such as rotten framing, is priced as a variation, which is a change to the agreed price and scope. Agree in writing how any variation will be priced before work starts.
How to Tell Which Pipes Your Home Has
Knowing the pipe material helps you follow the plumber's advice and compare quotes on equal terms. Look where pipes are exposed, such as beside the water meter, under the house, in the laundry, near the water heater and under sinks. Galvanised steel pipe is grey and heavy with joints that screw together, and a fridge magnet sticks to it because it is steel. Copper pipe is reddish brown, darkening or turning green with age, and a magnet will not stick to it. Plastic pipe comes in several colours, and the printing along its side names the material, size and maker.
Galvanised pipe is steel with a zinc coating to slow rust, and older NSW houses were plumbed with it for their water supply. Once the zinc wears through, the steel corrodes from the inside, and rust narrows the space the water flows through. Owners may notice brown water when a tap first opens, flow that falls away over several years and leaks at threaded joints. Sydney Water's pressure management program notes that corroded galvanised pipes may not work as well at lower pressure and may need upgrading. Because the corrosion runs along the whole pipe, replacing galvanised pipe one piece at a time can move the problem from joint to joint. Ask each plumber whether they recommend full or staged replacement for a galvanised system, and why.
Copper has a long history in Australian homes, and NSW Health notes that copper pipes are used extensively in plumbing systems. Copper pipes can last for decades, though bends, joints and fittings may wear and pinhole leaks can appear over time. Hunter Water says a metallic taste or blue-green stains on basins can come from copper in household pipes. It adds that this is more common in older homes or where taps have not been used for a while. If the problem continues after flushing, Hunter Water suggests asking a licensed plumber to inspect the pipes.
Plastic water pipes include cross-linked polyethylene, written PE-X, a flexible pipe used inside homes for hot and cold water. Polyethylene, written PE, is used for buried water services, and rigid PVC-U pipe made for water under pressure serves some cold water lines. Holman makes PVC-U pressure fittings for water supply, rated for 0 to 50 degrees Celsius with lower pressure ratings above 20 degrees. Iplex makes PVC-U pressure pipe and fittings, along with PE compression fittings and electrofusion fittings, which heat-weld plastic pipe. Older grey plastic pipe may be polybutylene, so photograph its printing and ask the plumber whether that pipe and its fittings should be replaced.
Quick Pipe Material Check
Look at the pipe beside the water meter, under the house and behind the laundry sink. Hold a fridge magnet against any grey metal pipe you can reach safely.
A magnet that sticks suggests galvanised steel, while copper and plastic pipes will not hold it. Photograph any printing on plastic pipe so the plumber can read the type.
Do not scrape, cut or force old pipes or the wrapping around them, since some older materials need testing first.
Signs Your Water Pipes Are Wearing Out
Some warning signs are visible around the house, while others only show up on the water bill or at the meter. Visible signs include rust stains or crusty deposits at joints, green staining on copper, damp patches on walls or ceilings and water pooling in the garden. Less obvious signs include brown water when taps first open, a metallic taste and a bill that rises with no change in use. Water is escaping somewhere on your side if the meter keeps turning while every tap is shut.
Finding a hidden leak is a separate skill from replacing pipe, and accurate detection saves opening walls in the wrong place. You can learn the meter test and the tracing tools plumbers use in our guide to water leak detection. Weak flow at every tap can also come from corroded pipe, though a closed valve or a street supply fault can cause the same symptom. Before paying for new pipes to fix weak flow, read our guide to low water pressure repairs and rule out cheaper causes first. A supply pipe condition inspection, estimated at $300 to $600, gives you a written view of the pipes before you commit to replacement.
A burst pipe needs urgent action rather than planning, and the first step is to turn off the water at the meter. Find the meter tap now, before anything goes wrong, so you can shut off the water quickly when it matters. Once the water is off, call a plumber who takes urgent jobs, which you can find through our emergency plumber page. Prices for fixing a burst, from exposed pipe to slab and buried lines, are compared on our page about burst pipe repairs. DEKS makes repair clamps, which a plumber can fit to hold a split pipe until the run is replaced. When the burst comes from pipe that is corroded along its length, get a separate quote to replace the run once the urgent repair is done.
One Section, Staged Work or a Full Repipe
Section replacement swaps one damaged length of pipe, such as the pipe under a kitchen or along one wall, and is estimated at $350 to $800. Staged replacement renews the pipes one area at a time, such as the service pipe first and the bathroom later, spreading the cost. Full repiping replaces every supply pipe from the meter to each fixture, estimated at $3,000 to $15,000 for a three-bedroom house. The right choice depends on the pipe material, how widespread the damage is and how long you plan to stay in the home.
Section replacement suits otherwise sound pipes with one damaged area, such as pipe crushed by tree roots or cut during building work. Staged work suits owners who want to spread the cost or who plan to renovate the bathroom, laundry or kitchen over the next few years. Whole-house repiping suits homes where every pipe is the same failing material, such as a house with galvanised pipe throughout. It also lets the plumber resize and reroute all the pipes at the same time, which is harder to achieve in stages.
Pipe size affects how well the house copes when several taps and appliances run at once. Plumbers size new pipes to suit the number of fixtures, the length of each run and the incoming pressure, following the national plumbing standard. Replacing a narrow service pipe with one of the same size can carry the old weakness into the new system. If you plan a second bathroom, a larger water heater or an extension, mention it now so the new pipes can be sized for it. Fitting larger pipes later means another trench or more wall work, so the cheaper path is to decide at the start.
Joining new pipe to old pipe of a different material needs transition fittings, which connect two pipe types, and the plumber should name them on the quote. REHAU's EDGE product book for Australia lists a fitting designed to join its PE-Xa pipe, a type of PE-X, to copper, one example of a transition fitting. SharkBite, a Reliance Worldwide Corporation brand, makes push-to-connect PEX fittings, which join when the pipe is pushed in, copper fittings and conversion fittings for joining different pipes. Staged work should begin where a failure would do the most damage, which often means pipes inside upper-floor walls or above ceilings. Keep a simple plan of what has been replaced and when, so the next stage can start where the last one finished. Ask how old pipes left in place will be cut off and sealed, so no unused length is left holding still water.
Choosing the Material for New Pipes
New water pipes in NSW homes are generally copper or plastic systems approved for drinking water. The Plumbing and Drainage Act 2011, which is in force in NSW, requires plumbing products to be authorised, and WaterMark is the national certification scheme, shown by a mark on approved products. The Australian Building Codes Board manages the WaterMark scheme, and products that need certification appear on its schedule of products. NSW Health also advises that pipes and fittings should comply with AS/NZS 4020, the standard for products in contact with drinking water, or carry WaterMark. Get the name of the certified system the plumber will use and keep the product details with your records.
Copper is rigid, copes with high temperatures and has been used in Australian plumbing for generations. Joints can be soldered or brazed, which melts a filler metal into the joint with a torch, or pressed, where a powered tool squeezes a fitting onto the pipe. Conex Bänninger makes >B< Press, a press fitting system for copper tube in sizes from 12 to 54 mm for hot and cold water. Pressed joints avoid an open flame inside wall cavities, which can matter in older homes with timber framing. Fittings and labour vary between materials as much as the pipe does, so compare the total quoted price for each option.
PE-X pipe bends without fittings, so it can be pulled through walls and roof spaces in long runs with fewer joints. REHAU makes EDGE, a PE-Xa pipe system in sizes from 16 to 32 mm for hot, cold, recycled and rainwater use. Viega makes Raxofix press connectors for PE-X and multi-layer pipe, and its Australian guide lists drinking water installations among their uses. Multi-layer pipe has a thin metal layer between plastic layers, which helps it hold its shape when bent. Each maker sets its own rules for bending, clipping and protecting its pipe, so the installer should follow that system's guide. Mixing one maker's fittings with another maker's pipe is something to raise with the plumber, since a warranty can depend on using a single system.
Buried water services between the meter and the house can use polyethylene pipe joined with compression or welded fittings. Vinidex makes PE pipe systems and PVC pressure systems, and Plasson makes PE pipe fittings, including its SmartFuse electrofusion range. Electrofusion fittings contain wires that heat and fuse the plastic when connected to a control unit, which produces a welded joint. Philmac makes a poly by poly stopcock, a shut-off valve that joins to plastic PE pipe at both ends, for buried lines.
Where only part of the house is being repiped, staying with the material already in place can keep the joins between old and new pipe simple. Where the whole system is being replaced, the plumber can choose copper or plastic for each run based on its route and use. Plastic pipe passing through timber or steel framing should be clipped in place and protected with a sleeve as its maker directs. Pipe exposed outside the house, such as the riser for an outdoor tap, needs a cover or a route inside a wall to protect it from knocks and weather, following the maker's guide. Whatever the choice, the quote should name the maker and the system so the warranty terms can be checked.
The Pipe Between the Water Meter and the House
The service pipe carries water from the meter to the house, and it runs underground where damage can go unseen for a long time. The water main, the large pipe in the street, and the water meter are Sydney Water's responsibility, and property owners are responsible for the other pipes. That means owners look after the pipes and fittings between the main and the buildings or taps on the property. The meter tap, the valve beside the meter, is private pipework, though owners can ask Sydney Water for a free courtesy repair under certain conditions. Call Sydney Water on 13 20 90 about faults on its side, and hire a licensed plumber for anything on the property side.
Under Sydney Water's policy, leaks on the short private section between its pipes and the meter are repaired free of charge, up to one metre inside the boundary. Leaks further inside the property are the owner's cost, so have the plumber measure where the fault sits before work starts. The utility adds that owners are responsible for private property affected by its repair work, such as garden beds or paving. Some homes share one private supply pipe with neighbours, called a joint water service, and those owners maintain that pipe and arrange how costs are shared. The private pipes supplying a property may run across a neighbour's land, Sydney Water notes, which can affect access for a trench.
Outside Sydney Water's area, water comes from Hunter Water, Central Coast Council or a local council supplier, depending on the town. Rules on meters, free repairs and contact numbers differ between suppliers, so look at your water bill to see who supplies you before booking. Essential Water serves Broken Hill, while in many other regional towns the local council supplies water and sewer services. To compare local plumbers in those areas, see our Newcastle and Hunter plumber page or our Central Coast plumber page.
Trenches, Buried Services and Before You Dig
Replacing a buried service pipe means opening a trench from the meter to the point where the pipe enters the house. Before anyone digs, the plumber should lodge an enquiry with Before You Dig Australia (BYDA), a single contact point for information on underground pipes and cables. BYDA offers free plans of utility pipes and cables near the work site, though it notes they may not show details within your property boundary. Tell the plumber where private pipes and cables run, such as a garden light circuit or a pool line. The sewer line can also run close to the water service, and a sewer service diagram, where one exists, shows where private sewer pipes sit.
Trench routes affect the price, because lawn is cheap to reopen while concrete, pavers and garden beds cost more to lift and relay. Check whether the plumber includes relaying concrete and paving or whether you need a separate trade afterwards. If the plumber does not relay hard surfaces, a paver can be found through our page on driveways and paving. Deep or long trenches may call for a small excavator, and contractors for that work can be found on our excavation services page. Tunnelling under a driveway, called boring, avoids cutting the concrete, but it is a specialist method that is priced per job.
Tree roots can crack or crush buried pipe, and a new trench is a chance to route the pipe away from large trees. Some councils protect significant trees, so check with your council before digging close to a large tree. Old clay sewer pipes found in the same trench may need their own repair, and repair options are compared in our guide to sewer line repairs. Agree before the trench is filled who will deal with any sewer problem, so the ground is not opened twice.
Running New Pipes Through Walls, Roofs and Floors
Inside the house, the new pipework can go beneath the floor, across the roof cavity or into channels cut into walls. Timber floors with a crawl space give the easiest access, since pipes can be clipped to the floor beams and reached again later. Roof space routes avoid lifting floors, though the pipes may need lagging, a foam sleeve that limits heat gain and loss. Concrete slab homes are harder, because pipes set in the slab cannot be replaced without cutting the floor. In slab homes, plumbers may leave the old pipes in the slab disconnected and run new ones through walls and ceilings.
Plumbers check walls for cables and pipes before cutting, both to avoid damage and to plan the shortest route. Electrical cables can share wall cavities with pipes, and any damage to wiring must be repaired by a licensed electrician. Once the walls are closed, owners fixing shelves or cabinets can check for hidden pipes first with a wall scanner. Bosch makes the D-tect 120 scanner, which its Australian site says detects water-filled plastic pipes and, to 120 mm deep, metals such as copper.
Pipes behind tiled bathroom walls are the costliest to reach, because tiles must come off and the waterproofing must be protected. Removing and replacing tiles to reach pipes in a wall is estimated at $200 to $600, and an access panel in a non-tiled wall at $150 to $300. Where a bathroom is due for renovation within a few years, replacing its pipes at that time can avoid paying for tiling twice. Rough-in, when pipes go in before the walls close, and fit-off, when fixtures connect, are the two stages of plumbing for a bathroom renovation that a repipe can be timed around. Kitchen pipes behind cabinets are simpler to reach, though base cabinets may need to be removed and refitted, so a planned kitchen sink installation is a sensible time for that work.
Making Good After the Pipes Are In
Making good means repairing the walls, ceilings, floors and paving opened for the work, and quotes handle it in different ways. Some plumbers patch holes roughly and leave finishing to the owner, while others include a plasterer and a painter. Ask for patching and painting as a separate line on the quote, since the standard of finish varies between plumbers. Where the plumber leaves walls open, a plasterer can finish them, and you can find one through our page on plastering and gyprock repairs.
Lifting floorboards or cutting into a slab brings its own repair work. Timber boards can be lifted and relaid, though older boards may split and need matching replacements. Cutting a concrete slab to reach in-slab pipe leaves a channel in the floor that must be filled and the floor covering replaced. Rerouting through walls and ceilings avoids slab cutting but leaves more plaster to patch and paint. Floor coverings such as carpet or vinyl may need a separate trade, so confirm who supplies and lays them. Compare those trade-offs on each quote, since the cheaper plumbing option can mean dearer finishing work.
Homes built before the late 1980s may contain asbestos, according to SafeWork NSW, which lists wall sheeting behind tiles and pipe lagging among the places it may be found. Lagging is the wrap around pipes, and old lagging on hot water pipes is one place to take care. Asbestos testing is estimated at $50 to $150 per sample, and it should happen before any sheet or lagging is cut or drilled. SafeWork NSW says removing more than 10 square metres of bonded (non-friable) asbestos needs a licence, and any amount of crumbly (friable) asbestos needs a friable removal licence. It recommends a licensed asbestos professional for any amount, and you can request quotes through our asbestos removal page.
Drinking Water Quality and Flushing New Pipes
Old pipes can affect what comes out of the tap, and NSW Health has published advice on metals from household plumbing. It says water left standing in pipes for long periods can contain higher levels of copper and sometimes lead. Its fact sheet on lead also notes that old household pipes may have been soldered with lead. To reduce exposure after water has been standing, NSW Health advises flushing cold taps for at least two minutes before drinking or cooking. Flushed water can still be used for washing up or watering plants, so it need not be wasted.
Rusty water does not always mean your own pipes are at fault. Hunter Water says brown or discoloured water can come from sediment stirred up in its network during maintenance or repairs. It advises running the outside tap closest to the meter for 10 minutes, then a backyard tap, and calling 1300 657 000 if the water does not clear. Water that clears at the front tap but stays brown inside the house suggests the problem lies in the private pipes. Note which taps run brown and when, since that record helps the plumber judge whether the pipes need replacing.
NSW Health also advises using the cold tap for drinking and cooking, because hot water systems may contain more dissolved metals. It notes that enHealth, the national environmental health committee, recommends flushing drinking taps for about 10 seconds first thing in the morning. New pipework should be flushed by the plumber before handover to clear swarf, the fine shavings from cutting, along with any other debris. For health questions about your water, the NSW Health website and your water supplier are the places to start.
Hot Water Lines, Valves and Insulation
Hot water pipes run from the water heater to the kitchen, bathroom and laundry, and they form part of any full repipe. Replacing them may involve work near the tempering valve, which blends hot and cold water to a safer temperature for bathroom taps and showers. All Valve Industries makes tempering valves and pressure control valves for residential water supplies. Plumbers may also suggest a new pressure limiting valve, which caps the pressure entering the home, estimated at $200 to $600 fitted. AS/NZS 3500.1, the national plumbing standard, caps pressure with all taps closed at 500 kilopascals (kPa) at any outlet inside a building other than fire service outlets. Where street supply pressure exceeds that figure, a pressure limiting valve is needed, and new pipework is a good time to check it alongside any water hammer and noisy pipe repair.
Lagging new hot water pipes reduces heat loss between the heater and the tap, so less water runs cold before the hot arrives. If the water heater itself is old, find out whether it makes sense to replace it while the water is already off. Heater types and their running costs are compared on our hot water services page. Fixing the pipes first and the heater later can mean two shutdowns and two sets of labour charges. Isolation valves at each fixture, estimated at $100 to $220 each, let future repairs happen without turning off the whole house.
Planning Water Shut-Offs and Living Through the Work
Repiping can leave a home without water for part of each day, so get a written schedule before work starts. Plumbers can install new pipes alongside the old ones and switch over room by room, which shortens the time without water. Keep water aside for drinking and cooking on shut-off days, and plan showers and washing around the switchover. Tell neighbours if a shared service or a trench near the boundary will affect them. Keep pets and children away from open trenches, and agree how the site will be made safe overnight.
Small sections can be finished in a day, while a full repipe can take several days depending on the size of the home and the access. Weekend and after-hours work costs more, with premiums estimated at 50 to 100 percent over standard rates. Booking planned work in business hours avoids those premiums unless the household cannot manage without water during the week. Agree on clean-up, removal of the old pipe and protection of floors and furniture before work starts.
Before walls are closed, the new pipework should be tested for leaks with the water on at full pressure. Find out from the plumber when the test will happen, so you can see the exposed joints yourself or have photos taken. Photos of pipe routes taken before plastering are useful later, since they show where pipes run behind finished walls. Store them with the Certificate of Compliance and the invoice for the work. They also help anyone who drills into those walls in future to avoid the pipes.
Replacing Pipes in Apartments and Strata Buildings
In apartments, some water pipes are common property, and replacing them falls to the owners corporation, the legal body that all the unit owners belong to. Common property means the parts of the building that all owners share, such as main walls and floors. Under the NSW Government's common property memorandum, pipes inside common property walls, floors or ceilings are the owners corporation's to maintain. The owners corporation also looks after the main stopcock to each unit, the valve that shuts off water to that lot. Pipes past a unit's stopcock that supply that unit alone, and do not run inside a common property wall, are that unit owner's job. Check your building's by-laws, its own written rules, with the strata manager before planning any work.
Building-wide repiping is a large project that the owners corporation plans through its capital works fund, the savings kept for major repairs, and general meetings. Owners planning work on their own lot pipes may need approval if the work touches common property walls or floors. For plumbers used to shared building systems, compare quotes through our page about strata and body corporate plumbing. Keep the strata manager informed, since a water shut-off in one unit can affect the neighbours.
Rural Blocks, Tanks and Long Service Runs
Rural and semi-rural homes can have long buried pipes from the meter, a tank or a bore to the house. Those runs can cross paddocks, driveways and gardens, so trench length becomes a major part of the price. Polyethylene pipe suits long buried runs because it comes in coils and needs few joints along the way. Where a pump supplies the house from a tank, the new pipes should suit the pump's output and the distance covered. Tank connections, pumps and devices that switch to mains water when the tank runs low are compared in our guide to rainwater tank plumbing. Isolation valves at the tank, the pump and the house make future repairs easier on long runs.
Call-out and travel charges weigh more heavily on remote properties, where a remote travel charge is estimated at $150 to $400. Bundling several jobs into one trip spreads that charge across more work. For inland properties, see the local plumbers on our pages for the Riverina and New England and North West. Councils supply water in many regional towns, so check with the council about meter location and its own rules before work starts. Older rural homes may still have their original galvanised or copper pipes, which can make one planned repipe simpler than repeated call-outs.
Landlords, Tenants and Home Buyers
NSW tenancy rules treat a burst water service or a serious leak as an urgent repair, along with failure of the water supply. When neither landlord nor agent can be contacted, the tenant may book a licensed tradesperson for the urgent repair and claim back up to $1,000. Repayment is due within 14 days of the tenant giving written notice with receipts attached. Planned repiping is not an urgent repair, so landlords should give notice and arrange access in line with tenancy rules. Unresolved repair disputes between tenants and landlords can be taken to the NSW Civil and Administrative Tribunal.
Landlords who want to pass on water usage charges must meet NSW water efficiency rules, which include no leaking taps or toilets at the start of a tenancy. Repiping is a good time to check those fittings against the requirements in our guide to rental water efficiency compliance. Routine upkeep across one or more rentals can be booked through our page on rental property maintenance. Tenants who notice rusty water or damp walls should report it in writing, since early reports can stop a slow leak becoming a larger repair.
Buyers can arrange for a plumber to check the pipes before purchase, noting the material, visible leaks and the water pressure. That visit differs from a general building inspection, and the two can be booked side by side. The checks a plumber makes are listed in our guide to a pre-purchase plumbing inspection, while inspectors can be compared on our building inspection page. The plumber can also note signs of past leaks, such as stains under sinks or swollen cabinet bases. Knowing the pipe material before you buy lets you factor a repipe into your budget or your offer.
Licences, Inspections and Paperwork
Plumbing work in NSW needs a licence whatever the job costs, and plumbing licences are issued under the Home Building Act 1989. Building Commission NSW regulates plumbers and can be reached on 13 27 00. You can check a plumber's licence, its categories and its expiry date on the NSW Government's Verify licence register under Contractors and tradespeople. Sydney Water says a confident householder can change a tap washer, but every other plumbing job, pipe replacement included, needs a licensed plumber. Doing your own pipe work is therefore not an option, even for a short exposed run under the house.
Before work begins, a Notice of Work is lodged, which is a form describing the plumbing and drainage work planned. Emergency work and minor works, such as replacing tapware or an existing hot water system, do not need one. At completion, the plumber fills in a Certificate of Compliance and gives a copy to the person who arranged the work. Sydney Water says the certificate confirms that the plumbing work meets the Plumbing Code of Australia, the national rulebook for plumbing. In Sydney, the Illawarra, the Blue Mountains, Newcastle and the Hunter, inspections go through the MyInspections Gateway, an online system for booking plumbing inspections, while local plumbing regulators handle them elsewhere. File the certificate with the house papers, so you can produce it when selling or making an insurance claim.
In NSW, home building work priced above $5,000, counting goods and services tax (GST), needs a written contract, and the deposit is capped at 10 percent. By law, major defects carry a six-year statutory warranty and other defects a two-year warranty. Full repipes and new buried services can pass the $5,000 mark, so read the contract carefully before signing. For other plumbing jobs and their prices, start at our NSW plumbing services hub.
Getting Comparable Quotes for New Water Pipes
Clear details at the start help each plumber price the same job. Tell them the age of the home, the pipe material if you know it, the number of bathrooms and whether the house sits on a slab or timber floor. Photos of the meter, exposed pipes, the water heater and any leaks help them arrive prepared. Mention the likely trench route, any paved areas and any large trees between the meter and the house. In Greater Sydney, you can request quotes from local plumbers through our hire a plumber in Sydney page.
A useful quote names the pipe system, the routes, the number of fittings and valves and the expected days on site. It should say who repairs plaster, tiles and paving, and whether old pipe is removed or left in place. Check that the Notice of Work, the Certificate of Compliance and any inspection fees are included in the price. For staged work, each stage should be priced separately so you can schedule them over time. Outside the cities, the estimated call-out fee falls to $60 to $120, with hourly labour at $70 to $150. Before committing to a full repipe, get three or more written prices from licensed plumbers.
Details to Send With Your Quote Request
The age of the home, the pipe material if known, the number of bathrooms and whether the floor is slab or timber. Any leaks, rusty water or weak flow you have noticed, and when they started.
Photos of the meter, exposed pipes, the water heater and any stains. The likely trench route, with paving, garden beds and trees marked on a rough sketch.
Clear details help plumbers quote the same scope, which makes their prices easier to compare.
What to Look Out For in Water Pipe Replacement Quotes
Be wary of a full repipe recommended without anyone inspecting the existing pipe or explaining why sections will not do. Quotes that give one lump sum with no pipe material, routes or making good listed are hard to compare and easy to dispute. Missing Certificate of Compliance details, or a plumber who will not give a licence number, are warning signs. Be cautious about a deposit above 10 percent on work priced over $5,000, since NSW rules do not allow it. Check that products carry WaterMark certification where needed, and that the plumber can name the system being used.
Watch for vague allowances like the phrase make good as required, which leaves the standard of finish open. A sound quote states what happens if hidden damage, asbestos or rotten framing turns up once walls are open. It should also give a price or hourly rate for extra work, so changes are agreed before they are done. Keep every quote, variation and invoice together with the certificate, since they help if a leak appears later.
Other Plumbing Work to Plan Alongside New Pipes
New pipes are a chance to fix other weak points while the water is off and walls are open. Worn taps and mixers can be swapped while the plumber is there, and the choices are compared in our tap and mixer installation guide. Old braided hoses under sinks and toilets can be swapped through flexible hose replacement at the same time, since they connect fixtures to the new pipes. Filtered drinking water taps and fridge water lines can be added while the plumbing is exposed, with options on our water filter and fridge water line page. Bundling these jobs saves a second call-out fee and a second water shut-off.
Drains and toilets are a separate system, but a plumber on site can look at them during the same visit. If a toilet keeps blocking, read our guide to blocked toilet repairs first so you can describe the problem clearly. Backflow devices, which stop water flowing back into the supply, are needed on some properties, and installers can be found on our page about backflow prevention devices. Mention any rainwater tank connected to the house, since tank connections to the mains have their own rules.
Pipe Replacement Plumbers in Every NSW Region
We connect homeowners, landlords and strata managers with licensed plumbers throughout New South Wales for pipe inspections, section replacements, new water services and full repipes. Post your job once and compare quotes from plumbers who work in your area.
▶ Sydney Inner City 18 areas
▶ Greater Sydney 25 areas
Western Sydney
South Western Sydney
Northern Sydney
The Hills District
Inner West
St George
▶ Sydney Coastal 23 areas
Northern Beaches
Eastern Suburbs
Harbour Suburbs
Sutherland Shire
▶ Hunter & Central Coast 19 areas
Central Coast
Hunter Valley
Port Stephens
▶ Illawarra & South Coast 18 areas
Illawarra
Shoalhaven
Sapphire Coast
▶ North Coast 19 areas
Mid North Coast
Coffs Coast
Northern Rivers
▶ Blue Mountains & Highlands 17 areas
Blue Mountains
Southern Highlands
▶ Regional NSW 21 areas
Central West
Riverina
New England
Far West
Water Pipe Replacement FAQs
How much does it cost to replace water pipes in NSW?
How do I know if my house has galvanised pipes?
Should I replace one section or repipe the whole house?
Is copper or PE-X better for new water pipes?
Does Sydney Water fix any of the pipe on my side of the boundary?
Will I be without water while the pipes are replaced?
Can old pipes affect my drinking water?
Does water pipe replacement need a Certificate of Compliance?
Is a leaking water pipe an urgent repair in a rental home?
Who replaces water pipes in an apartment building?
Trades That Help After New Pipes Go In
Related Services
For Trades & Contractors - NSW
Plumbers who take on repiping and new water services can browse current work on the NSW job leads board, along with plumber jobs in NSW and emergency plumber jobs.
Ready to Replace Old Water Pipes?
Post your job and compare quotes from licensed NSW plumbers for section replacements, new water services and full repipes.
Get Free Plumber QuotesAbout This Guide
This guide is general information only, and NSW rules, utility policies, product details and prices can change. Confirm requirements with your water supplier, Building Commission NSW, your owners corporation where relevant, and a licensed plumber before work starts.
Looking for more services across New South Wales? View all available trade services.
Reviewed by The Quote Yard Editorial Team
How The Quote Yard Works
We connect you with independent local tradies and service providers, we don't perform any trade work ourselves. Tradies provide their own quotes directly to you. Always confirm licensing, insurance, and scope of work before engaging any provider.