Fitting a New Kitchen Sink?

Tell us about the sink, the benchtop and any appliances connected under it, and we'll connect you with licensed plumbers near you.

Get Free Plumber Quotes

Typical Costs (2027 Estimates)

Call-out fee (business hours)$80-$150
Plumber hourly rate (business hours)$90-$180/hr
Sink swap, existing cutout (Sydney)$250-$500
Sink swap, existing cutout (regional)$210-$450
New sink and tap, new benchtop (Sydney)$400-$800
Plumbing moved to a new sink position$350-$900
Benchtop sink cutout (benchtop maker)$150-$400

These figures are 2027 estimates for NSW homes and exclude the sink and tap. Undermount fitting, a new drain outlet kit and floor repairs are priced per job.

Kitchen Sink Installation Services NSW - Get Local Quotes

Kitchen sink installation in NSW means taking out the old sink, setting a new one into the benchtop and connecting it to the water supply and the drain. A licensed plumber makes those connections, while a stonemason or cabinetmaker may cut the opening the sink sits in. Dropping a new sink into the same opening is the simplest version of the job. Moving the sink to an island or another wall means new pipes under the floor or inside the wall. Inset sinks rest on the benchtop, undermount sinks hang beneath it and farmhouse sinks show a deep front panel, and each style changes who does what. Heavy fireclay and farmhouse sinks also need a cabinet frame built to carry them when full of water. The plumber reconnects the dishwasher drain, any filter or boiling water unit, and the isolation valves, the small shut-off taps under the bench. Using 2027 estimates, fitting a sink into the existing cutout in Sydney costs about $250 to $500, and moving the plumbing to a new spot about $350 to $900. Older engineered stone benchtops can still be cut for a sink, but only with dust controls and a notice to SafeWork NSW. Choosing the sink and tap before the benchtop is made avoids extra cutting and a return visit to drill tap holes. Strata owners may need approval before a kitchen renovation, and taps, hoses and other plumbing products should carry WaterMark certification, the national approval mark. Keep the invoice and the Certificate of Compliance, the plumber's form confirming the work meets the rules, with your home records.

Kitchen Sink Plumbers Across NSW

Licensed plumbers fit inset, undermount and farmhouse kitchen sinks in houses, apartments and rentals across Greater Sydney, the Hunter, the Central Coast, the Illawarra and regional NSW. Describe the job once and we can put you in touch with up to three local plumbers for quotes you can compare.

Get Free Quotes

At a Glance - Kitchen Sink Installation in NSW (2027 Estimates)

Job 2027 Estimate (NSW) Suits Disruption Paperwork to Keep
Sink swap, existing cutout (Sydney) $250-$500 Same size sink in the same spot A few hours, sink out of use Invoice and Certificate of Compliance
Sink swap, existing cutout (regional NSW) $210-$450 Same job outside Sydney A few hours plus travel Invoice and Certificate of Compliance
New sink and tap, new benchtop (Sydney) $400-$800 Kitchen renovations Booked after the benchtop goes in Invoice and product warranties
Plumbing moved to a new sink position (Sydney) $350-$900 Island benches and new layouts Floor or wall opened Certificate of Compliance
Benchtop sink cutout $150-$400 New or widened opening Benchtop maker visit, dust controls for older engineered stone Benchtop maker's invoice
Filtered or boiling tap fitting (Sydney) $400-$900 Under-bench water units Same visit as the sink Invoice and unit warranty
Dishwasher connection $150-$300 Machine beside the sink One or two hours at most Invoice
New power point under the bench $150-$300 Dishwasher or boiling water unit Electrician visit Electrical compliance certificate

Cost Depth: What Moves a Sink Installation Price

Whether the sink stays in the same spot decides most of the price. A swap into the existing cutout costs about $250 to $500 in Sydney, while moving the plumbing to a new position adds roughly $350 to $900 before the sink is fitted.

The benchtop adds its own costs. A sink cutout by the benchtop maker is estimated at $150 to $400, drainer grooves (channels cut beside the sink) at $200 to $450, and removing an old benchtop at $400 to $900.

All figures are 2027 estimates for NSW and exclude the sink and tap. Slab cutting, cabinet repairs and regional travel can add to the final amount.

What a Kitchen Sink Installation Job Includes

Installing a kitchen sink brings together three parts of the kitchen: the benchtop that holds the sink, the cabinet below it and the pipes behind it. The plumber removes any old sink, sets the new bowl in place, connects the drain pipe and water lines, and tests every joint for leaks. Fitting the tap happens during the same visit, because it mounts on the sink itself or on the benchtop beside it. Connections for a dishwasher, a water filter or a boiling water unit under the bench are made at this stage too. For the price of the sink and tap themselves, compare the supply figures in our kitchen sink and tap cost guide.

The job also includes parts nobody sees once the cupboard doors close, such as the trap, the waste outlet and the hoses to the tap. A trap is the bend in the pipe under the sink that holds a little water and stops sewer smells rising into the kitchen. Flexible hoses are the braided lines that join the tap to the isolation valves, small shut-off taps on the wall or cabinet floor. New hoses are estimated at $30 to $60 a pair in parts, so check whether flexible hose replacement is included with the new sink.

Several trades can share the work, and knowing who does each step avoids gaps and double charges. Stonemasons and benchtop makers, often called fabricators, cut and polish the sink opening in stone and porcelain tops. Cabinetmakers and kitchen installers fit the base cabinet and may cut the opening in a laminate or timber benchtop. The licensed plumber makes every connection to the water supply and the drain, and checks that the sink sits level and drains fully. Electricians are needed only when a dishwasher, boiling water unit or food waste unit needs a new power point under the bench. If one company manages the whole kitchen, ask which of these people it sends and who holds the plumbing licence.

Swapping a Sink in Place or Moving It to a New Spot

In a like-for-like swap, the new sink goes into the same opening and connects to the pipes already there. That opening is called the cutout, and the new sink must suit its size and shape, so measure the old cutout before buying. According to our cost guide, a benchtop maker can make a stone cutout larger but cannot make it smaller. Any sink with a smaller outline than the old hole will not sit on the bench, and a larger one needs the cutout widened first. Inset sinks with a wide rim can sometimes cover a slightly bigger opening, which helps when the old model is no longer made.

Moving a sink to an island or another wall is a bigger plumbing job, because water lines and a waste pipe must reach the new spot. On a timber floor, the plumber can run pipes through the space below, while a concrete slab may need cutting to reach the drain. The waste pipe needs a steady downhill fall to the drain, so a long run from an island needs enough depth under the floor to keep that slope. Island sinks also raise the question of venting, which lets air into the drain so rushing water does not empty the trap. Ask the plumber to explain how the new drain will be vented and where an access point for clearing it will sit.

Relocating the plumbing at a kitchen sink is estimated at $350 to $900 in Sydney for 2027, before the sink itself is fitted. Cutting a concrete slab, long pipe runs and repairs to the floor finish can push the final cost above that range. Where the existing drain under the house is old or has blocked before, a drain camera inspection can show its condition before the new pipe joins it. Finding a cracked or sagging drain at this stage costs less than finding it after the new kitchen is in.

Inset, Undermount, Farmhouse and Flush-Mount Sinks

An inset sink, also called a top mount or drop-in sink, drops into the cutout and rests on its own rim. The rim sits on the benchtop and is sealed with silicone or a gasket, a soft strip that stops water getting under the edge. Clips under the rim pull the sink down tight, so the cabinet below needs room for the plumber's hands and tools. Inset sinks suit laminate, timber and stone benchtops alike, which makes them the simplest choice for a swap. Clark makes the Monaco Single Bowl Overmount sink, one example of a bowl that sits on the bench surface. Oliveri makes the Santorini Topmount Workstation Sink in matte black granite, another bowl that rests on its rim.

An undermount sink is fixed to the underside of the benchtop, so the polished edge of the cutout stays on show. That edge must be a material that can be finished and sealed, such as natural stone, porcelain or solid surface, a smooth acrylic benchtop material. As our cost guide points out, standard laminate is generally not suitable for an undermount sink. The bowl hangs from brackets or clips fixed under the benchtop, or rests on rails built into the cabinet, as its maker's instructions set out. Oliveri makes the Monet undermount sink with one and a half bowls, and its fixing method should be checked before the benchtop is ordered.

A farmhouse sink, sometimes called a butler sink, has a deep bowl with a front face that shows below the benchtop. Fireclay versions are heavy, so the cabinet under them needs a frame strong enough to carry the sink when it is full of water. The cabinet front is cut or built to suit the bowl, which means the cabinetmaker and plumber need the exact sink on site early. Oliveri makes the Sicily Farmhouse range of fireclay sinks, and Fienza makes Butler kitchen sinks among its collections. Order a farmhouse sink before the cabinets are built, because its measurements decide the size of the cabinet opening.

A flush-mount sink sits level with the benchtop surface, which needs a shallow step cut into the benchtop around the cutout. This style takes careful work by the fabricator, so confirm that your benchtop maker will do it before choosing the sink. Granite composite sinks are made from crushed stone bound in resin, and they come in inset and undermount versions. Franke makes Maris bowls in Fragranite, a sink material it describes as its own, and Fienza lists kitchen sinks in granite and 304 stainless steel, a common rust-resistant grade.

Stainless steel sinks are light enough for one person to lift, which keeps fitting time short. Granite composite and fireclay sinks weigh far more, so two people may be needed to set them into the cutout safely. Heavier bowls also need firmer support under an undermount fitting, using the brackets or rails the maker specifies. Tell the plumber the sink's material and weight when booking, so the right number of people turn up.

Matching the Sink to the Cabinet Below

Check the maker's product sheet for the cutout size and the smallest base cabinet the maker recommends for that sink. Measure the inside width and depth of the cabinet, not the door, because the side panels take up space. Deep bowls reduce the room left for the trap, the dishwasher drain connection and any filter below them. In a narrow cabinet, a double bowl sink can leave the second outlet sitting over a cabinet side, where no pipe can reach it. Send these measurements with the model number to the plumber, who can confirm the fit before you buy.

Bowl depth also sets how low the drain outlet sits, which changes where the trap meets the pipe in the wall. Choosing a deeper bowl than the old one can leave the outlet below the existing wall connection, so the plumber may need to lower that pipe. Lowering the connection in a timber-framed wall is a modest job, while a brick or tiled wall takes longer to open and repair. Before the sink is ordered, have the plumber compare the old and new outlet heights.

The Benchtop Cutout and the Order of Trades

On a stone or porcelain benchtop, the fabricator cuts the sink opening with water-cooled saws, in the workshop or on site. Undermount sinks need to be with the benchtop maker before templating, the visit where the benchtop is measured with a pattern. Tap holes are best drilled during fabrication, since our guide to kitchen benchtop installation notes that drilling them later adds a return visit. Sink cutouts are estimated at $150 to $400 for 2027, with undermount cutouts at the higher end because the edge must be polished. Drainer grooves, the shallow channels cut into the stone beside the sink to let water run back into the bowl, are estimated at $200 to $450.

Laminate and timber benchtops can be cut on site with a jigsaw, using the paper template supplied in the sink box. The raw edge of a laminate cutout must be sealed, because water reaching the particleboard, the pressed wood chip board underneath, makes it swell. This cut may be made by a cabinetmaker, a kitchen installer or the plumber, so confirm who is doing it when you book. Swelling around an old sink can mean the laminate top needs replacing, even if the new sink would fit the hole. Press along the benchtop edge beside your current sink and look for lifting or soft spots before ordering a sink that reuses the same top.

The order of visits is important when the benchtop is new, because each trade relies on the one before it. Plumbers may run drain and water pipes in the wall before the cabinets go in, then return once the benchtop is installed. Book these visits in writing with dates, and give the benchtop maker the sink and tap model numbers at the same time. A full kitchen renovation involves every step, while a stand-alone sink swap needs only one or two of them.

Old Engineered Stone Benchtops and the 2024 Ban

Engineered stone is a manufactured benchtop material made from crushed stone bound with resin, and it was common in kitchens built before the ban. SafeWork NSW says the ban on manufacturing, supplying, processing and installing engineered stone benchtops, panels and slabs took effect on 1 July 2024. The ban covers engineered stone with at least 1 percent crystalline silica by weight, a mineral whose fine dust harms the lungs when breathed in. Benchtops already in homes are called legacy stone, and SafeWork NSW says they are safe while left undisturbed. You do not have to remove an existing engineered stone benchtop just because the ban exists. The rules matter once a sink job needs that benchtop cut, drilled or ground.

Cutting, drilling or grinding legacy stone with power tools, known as processing, is allowed only when the work is controlled and the worker uses respiratory protective equipment, such as a fitted respirator. SafeWork NSW must also be told about the processing work expected over the next 12 months. Widening a sink cutout or drilling a new tap hole with power tools counts as processing, so ask how the benchtop maker meets these rules. SafeWork NSW advises against doing DIY work on engineered stone benchtops, so leave any cutting, drilling or grinding to a qualified tradesperson. Choosing a new sink that fits the existing cutout exactly avoids cutting the stone at all.

SafeWork NSW also lists kitchen sinks among the finished engineered stone products excluded from the ban when they need no cutting or shaping. Such a sink can still be fitted, provided nobody has to cut or grind it on site. Replacing an old engineered stone top with natural stone, porcelain or laminate is a separate job, priced under stone benchtop replacement and upgrades. Removing an old benchtop is estimated at $400 to $900 for 2027, and any cutting during removal falls under the same SafeWork NSW rules.

Kitchen Sink Installation Prices for 2027

Installation prices depend on the type of sink, whether the plumbing moves and how much other work happens on the same visit. Call-out fees in business hours, the charge for coming to your home, are estimated at $80 to $150, with labour at $90 to $180 an hour. Plumbers commonly charge at least one hour of labour, according to our NSW pricing pages, so a short visit can still be billed as a full hour. Every figure below is a 2027 estimate drawn from Quote Yard NSW pages, and the Sydney fitting figures come from our sink and tap cost guide. Check whether each price quoted includes the call-out fee, since some plumbers list it separately.

Job 2027 Estimate (NSW) What Drives the Price
Call-out fee (business hours) $80 to $150 Distance, time of day and whether the first hour is included
Plumber labour (business hours) $90 to $180 an hour Extra work found once the old sink is out
Sink swap into the existing cutout (Sydney) $250 to $500 Sink type, drain outlet kit, valve condition
Sink swap into the existing cutout (regional NSW) $210 to $450 Region and travel distance
New sink and tap into a new benchtop (Sydney) $400 to $800 Undermount fixing, number of bowls, tap type
Plumbing relocation at the sink (Sydney) $350 to $900 Floor type, distance to the drain, drain air vent
Benchtop sink cutout (benchtop maker) $150 to $400 Material, undermount edge polishing
Drainer grooves in a stone benchtop $200 to $450 Length and number of grooves
Kitchen tap swap, existing holes (Sydney) $180 to $350 Mixer type and access under the sink
Filtered or boiling tap fitting (Sydney, labour) $400 to $900 Unit size, new tap hole, power point
Dishwasher connection $150 to $300 ($300 to $500 with a new water point) Existing valve and drain connection, cabinet access
Old dishwasher removal $50 to $100 Disposal arrangements
Isolation valve replacement $100 to $220 Number of valves and pipe condition
Undermount fitting extra, sink drain outlet or trap replacement Priced on quote No published range; parts and fixing time

Regional NSW sink swaps are estimated at $210 to $450, a little below the Sydney range of $250 to $500. Our cost guide gives $220 to $430 for Newcastle and the Hunter, and $230 to $450 for the Central Coast. Long travel distances can still add to a regional quote, so ask whether a travel charge applies before booking. Undermount sink fitting has no separate published price range, so the plumber should price it on quote after seeing the benchtop. Extra time for brackets, adhesive and clamping is what lifts an undermount fitting above a simple swap.

Adding the price ranges together gives a rough guide, though the written quote after a site visit is the figure that counts. Suppose you buy a stainless steel sink, typically $150 to $800, and have it fitted into the existing cutout in Sydney. The fitting adds about $250 to $500, which brings the total to $400 to $1,300 before any extras. Adding a new drain outlet, strainer basket and accessories kit, roughly $50 to $300, takes the range to $450 to $1,600. Swapping the tap during the same visit costs about $180 to $350, though some plumbers include it in the sink fitting price. Check whether the tap appears as its own line on the quote or sits within the sink fitting.

Moving the sink to a new position adds several items to the bill at once. Relocating the plumbing is estimated at $350 to $900, a new cutout at $150 to $400, and fitting a sink and tap into a new benchtop at $400 to $800. Together those ranges come to $900 to $2,100, before the sink, the tap or any floor and wall repairs. Granite composite sinks cost about $300 to $1,200 to buy and fireclay sinks $400 to $1,200, so the material moves the total further. Once a combined kitchen job passes $5,000 including GST, NSW requires a written contract for the residential building work.

Some costs appear only once the old sink is out, such as a rotten cabinet base or a corroded valve. Agree in writing how any extra work found on the day will be priced before the plumber starts. Replacing an isolation valve costs an estimated $100 to $220, worth knowing when an old valve will not turn off fully. After-hours labour runs at about $150 to $250 an hour, so planned sink work is best booked in business hours, and our NSW plumber pricing guide lists the other rates.

Where the Bands Come From

Sydney fitting figures, regional sink swaps and supply prices are taken from our kitchen sink and tap cost guide. The cutout, drainer groove and benchtop removal figures are drawn from our kitchen benchtop installation guide.

For dishwasher connection, old dishwasher removal and power point figures, we used our dishwasher installation guide. Call-out, hourly and after-hours rates match those on our NSW plumbing price pages.

All figures are 2027 estimates for NSW. Undermount fitting, a new sink drain outlet and tap holes drilled into an existing benchtop have no published range and are priced on quote.

The Waste Pipe, Trap and Drain Under the Sink

The waste is the outlet at the bottom of the bowl, and it includes the strainer basket that catches food and the plug that holds water in. Below the waste sits the trap, then a pipe that runs through the wall or floor to the drain. Double bowl sinks need both outlets joined before the trap, using a connector that suits the sink and the space below it. The waste kit does not always come with the sink, so check the box contents and ask the plumber which waste suits the bowl. Replacing the waste or trap has no published price range, so expect it to be priced on quote with the parts listed.

Installing a new sink is a good time to look at the drain it connects to. If the old sink drained slowly, the cause may lie in the pipe that runs from the trap to the main drain, and a new bowl will not fix it. Where the drain is already slow, book blocked sink and basin repairs before the new bowl goes in so the plumber clears the pipe first. Clearing a blockage before installation costs less than lifting the new sink out again later. Scrape plates into the bin before washing up, so fat and food scraps do not build up in the new pipes.

Some sinks have an overflow, a small opening near the top of the bowl that drains water away if the sink is overfilled. The overflow joins the waste through a short hose, and that joint is checked for leaks with the bowl filled. Every joint under the sink should be tested with running water and a full bowl before the plumber leaves. Watch this test if you can, and look under the sink again the next morning for drips or a damp cupboard floor.

Water Supply, Isolation Valves and Tap Holes

Kitchen sinks take a hot and a cold supply, and each line should have its own isolation valve under the sink. An isolation valve is a small tap on the pipe that turns off one fixture without shutting down water to the whole house. If your kitchen has none, adding them during a sink job means later tap repairs need no full shut-off. The hoses joining these valves to the tap should be WaterMark certified, the national mark showing a plumbing product is approved for use. That scheme is run by the Australian Building Codes Board, and NSW plumbing law requires authorised products for work like this.

Mixer taps mount through a single hole in the sink or benchtop, while older two-tap sets need two or three holes. Pick the tap before the sink is cut or ordered, because a hole cannot be filled neatly once it is made. Greens Tapware makes the Mika Pull-down Sink Mixer, and hansgrohe makes kitchen mixers such as the Talis M54 and Aquno Select M81. Pull-down mixers keep a hose inside the spout, so leave clear space below the sink where that hose moves. Nero Tapware makes the Mecca Smart Sensor Pull-Out Kitchen Mixer, a touch-free design, so read its installation notes for any power or battery needs. When choosing the tap itself, compare spout reach and styles in our guide to tap and mixer installation.

AS/NZS 3500.1, the water supply plumbing standard published by Standards Australia, sets a maximum static pressure of 500 kPa (kilopascals, the unit for water pressure) at any outlet inside a building. Static pressure means the pressure in the pipes when no tap is running, and a pressure limiting valve, which lowers incoming pressure, is needed where mains pressure is higher. High pressure strains hoses and the cartridges, the valve parts inside a mixer, so ask the plumber to check it when a new sink and mixer go in. Pipes that bang when the new mixer shuts off quickly can point to the same pressure problem, which water hammer and noisy pipe repair can fix. A weak flow from the new tap can come from a blocked aerator (the spout's mesh screen), a part-closed valve or the supply pipe, and a low water pressure repair visit can find which.

Connecting the Dishwasher at the Sink

Dishwashers beside the sink draw water from a supply valve under the bench and drain through the sink waste. Each machine's drain hose joins a spigot, a short side outlet on the sink trap or waste made for this purpose. Fisher & Paykel makes DishDrawer dishwashers, and its Australian guide for one double model sets the drain hose loop at least 150 mm above the joiner, the spigot on the sink trap. That high loop stops dirty water in the sink waste from running back into the machine. The same guide recommends a cold water connection and says the plumber and electrician are each responsible for making the installation comply.

The guide also places the power outlet in a cabinet next to the dishwasher space, where it can still be reached once the machine is in. Adding that outlet is electrical work for a licensed electrician, and power point installation is estimated at $150 to $300. Westinghouse makes dishwashers too, and the installation guide for whichever brand you choose should be read before the cabinet layout is fixed. A standard dishwasher installation costs about $150 to $300, or $300 to $500 where a new water point is needed. If you are choosing a machine at the same time, compare freestanding, integrated and drawer models in our guide to dishwasher installation.

Removing the old dishwasher is estimated at $50 to $100, and it can be done during the same visit as the sink. Turn off the dishwasher's water and power before the plumber arrives if you know where the valve and switch are. Run an empty cycle once everything is reconnected and check the sink waste for drips while the machine drains. Even a small leak at the drain spigot can soak the cabinet floor for weeks before anyone notices it.

Filters, Boiling Water Units and the Cupboard Below

The cupboard under a kitchen sink can hold far more than pipes, and the plumber needs to plan around everything going in it. Under-bench filters, boiling water units, waste bins and drawers all share the space with the trap and valves. Puretec makes kitchen undersink filters and replacement cartridges, and the filter housing must stay within reach for cartridge changes. Billi makes the Billi Home BC with Multifunction Mixer Tap, a boiling and chilled water system served through one tap at the sink. Boiling water taps need a dedicated power point under the sink, as our cost guide points out, which is work for an electrician.

Filtered or boiling tap installation is estimated at $400 to $900 in labour for Sydney, on top of the unit itself. Fitting it at the same time as the new sink saves a second visit and lets the tap hole be drilled before the benchtop goes in. Units differ in size and clearance needs, so read the maker's installation guide before the cabinet is ordered. Fridge water lines can run from the same cold supply with their own valve, as described in our guide to water filter and fridge water line installation. Labels on each valve under the sink help anyone find the right one quickly during a leak, so request them from the plumber. Write the filter's cartridge change dates inside the cupboard door so they are not forgotten.

Sink cabinets with drawers instead of doors change where the trap and pipes can sit. Blum makes LEGRABOX drawer systems and sink cabinet fittings that it says maximise storage around the sink. Drawers under a sink are shaped to clear the waste pipe, so the plumber must keep pipes inside the space the cabinet allows. Give the plumber the drawings from your cabinetmaker before rough-in, the stage when pipes are run before the cabinets go in. Moving a trap later to clear a drawer costs more than placing it correctly the first time.

Second Sinks in Pantries, Bars and Outdoor Kitchens

Some kitchens now add a second, smaller sink in a butler's pantry, a bar area or an island preparation zone. Abey makes bar sinks alongside its kitchen and laundry sinks, for spaces where a full-size bowl would not fit. Second sinks need their own waste connection and water supply, and they may share a drain with the main sink if the layout allows. Each extra connection adds plumbing time, so ask for the second sink to be priced as its own line on the quote. The drain's air vent and downhill slope need the same care as an island sink, especially when the pantry sits away from an outside wall.

Butler's pantry sinks suit households that run a second dishwasher or prepare food out of sight of the main kitchen. Plan the pantry plumbing at the same time as the main kitchen, so the rough-in for both happens in one visit. Tap holes and cutouts for the second sink follow the same benchtop maker's steps as the main bowl. Where the second sink goes into an engineered stone benchtop already in place, the SafeWork NSW rules for legacy stone apply to any new cutout. Outdoor sinks on a patio or deck need drainage planned from scratch, and they are priced as outdoor fridge and sink installation work. Group all the sinks and any outdoor tap installation into one quote request so the plumber can plan shared pipe runs.

Older Kitchens: Asbestos, Old Pipes and Water Damage

Pulling out an old sink can uncover problems that were hidden behind the cabinet for years. The NSW Government warns that homes built before 1990 may contain asbestos, and it lists kitchen splashbacks among the places it can be found. If an old splashback or wall sheet must be cut or drilled for new pipes, the NSW Government advises an assessment by a licensed asbestos assessor before anyone disturbs it. Removal of confirmed asbestos is a job for an asbestos removal specialist working under SafeWork NSW rules. Do not sand, drill or break old sheeting yourself while you wait for the result.

Old galvanised steel pipes, which rust from the inside, may still feed the sink in some older kitchens. Replacing the short runs inside the cabinet makes sense while the new sink goes in, since that area is already open. Where rust, weak flow or leaks appear throughout the house, our guide to water pipe replacement compares a section repair with replacing all the pipes. Copper joints with green crusting should also be checked while the sink is out. Small fixes at this stage cost less than opening up a brand new cabinet later.

Water leaking slowly under an old sink can soften the cabinet base and the floor beneath it. Press the cabinet floor and look for swelling, staining or a musty smell before the new sink is ordered. Damaged cabinet bases need a carpenter or cabinetmaker before the plumber can fit the new sink. If you suspect a hidden leak in the wall or floor, water leak detection can find it before the new kitchen covers it.

Apartments, Strata Approval and Rented Homes

In a strata building, the NSW Government classes kitchen renovations, such as installing or removing cupboards, as minor renovations. Minor renovations need approval, with more than half of the votes cast at a strata meeting in favour of the work. Work that changes the structure of the building or needs waterproofing is a major renovation and needs a special resolution. A special resolution passes when no more than a quarter of the value of the votes cast are against it. Check your by-laws, the building's own rules, before booking even a simple sink swap, since they can set work hours and lift bookings. For how repair duties are split between owners and the owners corporation, the body of all owners that runs the building, see our guide to strata and body corporate plumbing.

Landlords replacing a kitchen sink tap in a rented home should keep the new flow rate in mind. Under NSW rules from 23 March 2025, kitchen sink taps must flow at no more than 9 litres a minute if the landlord passes on water usage charges. The same rules require no leaking taps at the start of a tenancy or when fittings are installed, repaired or upgraded. Evidence can be a written statement or report from a licensed plumber confirming the flow rate, kept in the tenancy file. For each requirement and the records to keep, read our guide to rental water efficiency compliance.

Tenants should not replace a sink or tap themselves, because the fitting belongs to the landlord and the work needs a licence. Serious leaks under the sink are among the urgent repairs listed under NSW tenancy rules. If the landlord or agent cannot be reached, a tenant may use a licensed tradesperson for urgent repairs up to $1,000 and be repaid within 14 days of giving notice. Outside business hours, an emergency plumber can stop the leak, and slower faults should be reported to the landlord in writing.

Landlords can plan a sink replacement for the gap between tenancies, when the kitchen is empty and access is easy. During a tenancy, give tenants written notice before any work, following the NSW notice rules for entering a rented home. Keep the plumber's flow statement, invoice and any certificate with the property file for the next lease. Fitting a compliant tap with no leaks alongside the new sink also helps the home meet the water efficiency rules above. Agents managing several homes can ask one plumber to quote the same sink and tap model across them.

Licences, WaterMark and the Paperwork

Plumbing work in NSW needs a licence regardless of the job's cost, and Building Commission NSW issues those licences under the Home Building Act 1989. You can check a plumber's licence on the NSW Government's Verify licence register before the job is booked. Sydney Water says a confident householder can change a tap washer, but every other plumbing job needs a licensed plumber. Disconnecting and reconnecting a sink's waste and water lines is plumbing work, so it needs a licensed plumber too. Building Commission NSW answers questions about licences and complaints on 13 27 00. Make sure the plumber's licence number appears on both the quote and the invoice.

The NSW Government lists replacing tapware among the minor works that need no Notice of Work, the form a plumber lodges before certain jobs begin. New drainage is involved when a sink moves to a new position, so check with the plumber which forms apply to your job and area. At the end of the work the plumber must complete a Certificate of Compliance, a form confirming it meets plumbing standards, and give a copy to the person who arranged it. Where work needs an inspection in Sydney, the Illawarra, the Blue Mountains, Newcastle or the Hunter, the plumber lodges through the MyInspections Gateway, an online booking system, and elsewhere with the local plumbing regulator. File these documents with your home records, because buyers and insurers may ask for them later.

Residential building work over $5,000 including GST needs a written contract, and the deposit cannot be more than 10 percent. Warranties set by law, called statutory warranties, apply to that work, with six years for major defects and two years for other defects. The sink and tap also carry the maker's own warranty, so register the products and keep the receipts. Consumer guarantees under the Australian Consumer Law also apply to products and services, and the ACCC publishes guidance on them.

Getting the Kitchen Ready for Installation Day

Clear the cupboard under the sink and the benchtop around it the night before the plumber arrives. Have the new sink, tap, waste kit and installation instructions on site and unpacked, so the plumber can check every part. Inspect the sink for chips, dents or cracks when it is delivered, since damage found after fitting is harder to claim. Know where the main water shut-off valve is, in case the supply to the whole house must be turned off. Plan meals around a day without a working sink, especially when silicone or adhesive needs time to set.

Clear a path from the front door to the kitchen, since an old sink and a new boxed one are awkward to carry. In an apartment, book the service lift and check the building's permitted work hours with the strata manager. Lay a drop sheet or old towels on the floor in front of the cabinet, where water left in the old pipes will spill. Keep children and pets out of the kitchen while pipes are open and tools are on the floor. Agree in advance who takes the old sink away, whether it goes to a metal recycler or the tip.

On the day, the plumber turns off the water, disconnects the old sink and lifts it out. The new sink is set in the cutout, sealed or fixed, and then the waste, trap and water lines are connected. Simple swaps can take a few hours, while an undermount sink may need a second visit once the fixing adhesive has set. Before the plumber leaves, run both taps, fill the bowls and check under the sink with a torch.

Getting Comparable Quotes for a New Kitchen Sink

Quotes are easier to compare when every plumber gets the same information. Send photos of the current sink, the cabinet underneath and the benchtop edge, along with the new sink and tap model numbers. Say whether the sink stays in the same spot or moves, and whether a dishwasher, filter or boiling water unit connects to it. Mention the benchtop material, since stone and engineered stone change who must cut it and how. Post your job once through our plumbing services page, and up to three local plumbers can quote on exactly the same job.

Details to Send With Your Quote Request

Your suburb, the sink and tap model numbers, the benchtop material, and whether the sink stays in place or moves. Photos of the cupboard under the sink, the existing valves and the benchtop edge.

Any connected appliances, such as a dishwasher, filter or boiling water unit. Whether you live in a strata building, the age of the home, and any slow drains or past leaks you know about.

Clear details help each plumber price the same job, which makes the quotes easier to compare.

Renovation plumbing quotes can be split into two stages, called rough-in and fit-off. Rough-in is the pipe work done inside walls and floors before the cabinets and benchtop arrive. Fit-off is the return visit when the sink, tap and appliances are connected once the benchtop is in place. Check that both stages and any extra visit charges appear on the quote, so the second visit costs no more than expected.

Each quote should list the sink fitting, any tap fitting and every connection as separate items. Parts such as wastes, traps, hoses and valves should appear with their prices, or with a note that they are included. Disposal of the old sink should be stated, along with any charge for removing the old dishwasher. Look for the call-out fee, the hourly rate for extra work and the plumber's licence number. Check whether the quote assumes the cutout is ready or includes the fabricator's work as well. Compare the figures you receive with the ranges in the table above before you accept a price.

What to Look Out For in Kitchen Sink Installation Quotes

Be wary of a quote that offers to cut or drill an engineered stone benchtop with no mention of dust controls. Under SafeWork NSW rules, that work needs controlled cutting methods, a fitted respirator or similar protection, and a notice to the regulator. Missing licence numbers, or a plumber who suggests skipping the compliance paperwork, are further warning signs. Products bought online from overseas may lack WaterMark certification, and a licensed plumber can decline to fit them. Check the WaterMark details on the box before you pay for a sink mixer or hose online.

Watch for vague wording such as a single line for connecting the sink, with no detail on the waste, trap, valves or dishwasher spigot. Low prices that leave out the waste kit and hoses can end up higher than a quote that includes them. Requests for a large cash deposit are also a concern, since NSW caps deposits at 10 percent on contracts over $5,000. Ask for any change of price to be agreed in writing before the extra work starts.

Checking the New Sink in the First Weeks

Look under the sink each day for the first week, and run a hand along each joint to feel for damp. Dry paper towel wrapped around the trap and hose joints makes small drips easy to spot. Check the silicone around an inset sink for gaps, and keep it dry for the time its maker states before heavy use. Call the plumber back promptly if water appears, because a small leak can ruin a cabinet base. Keep the invoice, product warranties and any certificate together with the sink's model number.

While on site for a new sink, the plumber can also handle nearby jobs, which saves a second call-out fee. If the laundry shares a wall or drain with the kitchen, laundry sink installation can be quoted at the same time. Fixing a leaking tap in the bathroom during the same booking also cuts travel charges. Other water and drain jobs in the room can be grouped as kitchen plumbing work in the same written quote. Request a separate price for each item so you can drop any that do not fit the budget.

Kitchen Sink Plumbers in Every NSW Region

We connect homeowners, landlords and strata owners with licensed plumbers throughout New South Wales for kitchen sink swaps, undermount and farmhouse sinks, and sinks moved to new positions. Post your job once and compare quotes from plumbers who work in your area.

▶ Sydney Inner City 18 areas
Sydney CBD Surry Hills Darlinghurst Potts Point Paddington Redfern Newtown Glebe Balmain Pyrmont Ultimo Chippendale Alexandria Waterloo Zetland Erskineville Rozelle Leichhardt
▶ Greater Sydney 25 areas

Western Sydney

Parramatta Penrith Blacktown Mount Druitt Seven Hills Wetherill Park Auburn Fairfield Cabramatta St Marys

South Western Sydney

Liverpool Campbelltown Bankstown Revesby

Northern Sydney

Hornsby Chatswood Epping Macquarie Park Eastwood

The Hills District

Castle Hill Baulkham Hills

Inner West

Ryde Strathfield Burwood

St George

Hurstville Kogarah
▶ Sydney Coastal 23 areas

Northern Beaches

Manly Dee Why Curl Curl Freshwater Brookvale Collaroy Narrabeen Mona Vale Newport Avalon Palm Beach

Eastern Suburbs

Bondi Tamarama Bronte Coogee Maroubra Randwick

Harbour Suburbs

Double Bay Rose Bay Watsons Bay

Sutherland Shire

Cronulla Miranda Sutherland
▶ Hunter & Central Coast 19 areas

Central Coast

Gosford Terrigal Wyong The Entrance Tuggerah Erina Woy Woy

Hunter Valley

Newcastle Maitland Lake Macquarie Charlestown Belmont Raymond Terrace Cessnock Singleton Muswellbrook

Port Stephens

Nelson Bay Salamander Bay Shoal Bay
▶ Illawarra & South Coast 18 areas

Illawarra

Wollongong Shellharbour Kiama Dapto Corrimal Thirroul Gerringong

Shoalhaven

Nowra Berry Ulladulla Huskisson Vincentia

Sapphire Coast

Batemans Bay Moruya Narooma Bega Merimbula Eden
▶ North Coast 19 areas

Mid North Coast

Port Macquarie Forster Taree Kempsey Laurieton

Coffs Coast

Coffs Harbour Bellingen Sawtell Grafton Yamba

Northern Rivers

Byron Bay Tweed Heads Ballina Lismore Bangalow Lennox Head Brunswick Heads Mullumbimby
▶ Blue Mountains & Highlands 17 areas

Blue Mountains

Katoomba Leura Wentworth Falls Blackheath Springwood Hazelbrook Glenbrook Faulconbridge Lawson Blaxland Lithgow

Southern Highlands

Bowral Moss Vale Mittagong Bundanoon Robertson Berrima
▶ Regional NSW 21 areas

Central West

Orange Bathurst Dubbo Mudgee Parkes Forbes Cowra Young

Riverina

Wagga Wagga Albury Griffith Leeton Goulburn Queanbeyan

New England

Tamworth Armidale Inverell Moree Narrabri

Far West

Broken Hill Cobar

Kitchen Sink Installation FAQs

Will a new kitchen sink fit the hole left by my old one?
It will only if the new sink's cutout size matches the old opening or its rim is wide enough to cover it. Measure the length, width and corner shape of the existing cutout, then compare those figures with the maker's cutout template. Fabricators can enlarge a stone cutout but cannot make it smaller, so a sink that is too small for the hole will not work. Undermount sinks are the hardest to swap, because the polished edge of the old cutout must line up with the new bowl. Send the plumber photos and measurements before buying to avoid an expensive mismatch.
Who cuts the hole in a stone benchtop for an undermount sink?
The benchtop fabricator or stonemason cuts and polishes the opening, not the plumber. For a new benchtop, the undermount sink must be with the fabricator before templating, the measuring visit for the stone. Tap holes are drilled at the same stage, so choose the tap early. Expect a sink cutout to cost an estimated $150 to $400 for 2027, with undermount cutouts toward the top of that range. The plumber then connects the waste and water lines once the benchtop is installed.
Can my old engineered stone benchtop be cut to fit a new sink?
It can, but only under SafeWork NSW rules for legacy stone, meaning engineered stone installed before the ban began on 1 July 2024. Cutting, drilling or grinding it with power tools must be controlled, and the worker must wear a fitted respirator or similar protection. SafeWork NSW must also be told about the cutting, drilling or grinding work expected over the next 12 months. Homeowners should not cut or drill it themselves, because SafeWork NSW advises against DIY work on engineered stone. Choosing a sink that fits the existing cutout avoids cutting the stone at all.
How long will my kitchen be without a working sink?
Like-for-like swaps into an existing cutout can be finished within a few hours on a single visit. Undermount sinks may take longer, because adhesive or brackets need time to set before the waste is connected. When the sink moves to a new spot or a new benchtop is being made, the kitchen may be without a sink for days between trade visits. Get a date in writing from each trade and plan simple meals for the gap. In the meantime, a laundry sink or bathroom basin can serve for washing up.
Does the plumber reconnect the dishwasher when fitting a new sink?
Yes, the plumber reconnects the dishwasher drain hose and water supply during the same job, so mention the dishwasher when asking for quotes. The drain hose joins a spigot on the sink trap or waste, and makers set out how high the hose must loop. Fisher & Paykel's Australian guide for one DishDrawer model sets that loop at least 150 mm above the joiner. Any new power point for the dishwasher must be added by a licensed electrician. Connecting a standard dishwasher is estimated at $150 to $300 for 2027.
Do I need strata approval to replace the sink in my apartment?
The NSW Government classes kitchen renovations, such as installing or removing cupboards, as minor renovations needing approval from the owners corporation, the body of all owners. Work that changes the building's structure or needs waterproofing is a major renovation requiring a special resolution. Ask your strata manager whether a simple sink swap counts as a minor renovation, and check by-laws on work hours, lifts and water shut-offs. Get that answer in writing before booking the plumber. Where water must be turned off to other units, the strata manager will need to arrange it.
Can I set the new sink in place myself and get a plumber to connect it?
Sydney Water says a confident householder can change a tap washer, but every other plumbing job needs a licensed plumber. Connecting the waste, trap and water lines is plumbing work, so a licensed plumber must do it. Some plumbers prefer to set the sink themselves, because they are then responsible for how it sits and drains. Check with the plumber before you start, since a sink fitted badly by someone else may need to come out again. Never cut an engineered stone benchtop yourself to prepare for the new sink.
What does a kitchen sink installation cost in NSW in 2027?
Fitting a sink into the existing cutout is estimated at $250 to $500 in Sydney and $210 to $450 in regional NSW for 2027. A new sink and tap fitted into a new benchtop costs about $400 to $800 in Sydney. Moving the plumbing to a new position adds an estimated $350 to $900, and a benchtop cutout adds $150 to $400. These figures exclude the sink and tap themselves, which are bought separately. Business-hours call-out fees of $80 to $150 may also apply.
What paperwork should I get after a new sink is installed?
Ask for a tax invoice showing the plumber's licence number, the work done and the parts supplied. Plumbers must complete a Certificate of Compliance when the work is finished and give a copy to the person who arranged it. Keep the sink and tap warranty cards, the receipts and the model numbers in the same folder. Jobs over $5,000 including GST also need a written contract, which should be filed with the rest. These records help with warranty claims, insurance questions and a future sale.
Can a kitchen sink be moved to a new island bench?
Yes, a licensed plumber can run new water lines and a waste pipe to an island, but it is a bigger job than a swap. The waste pipe needs a steady downhill fall to the drain, which is easier under a timber floor than through a concrete slab. Island sinks also need a way for air to enter the drain, so ask how the plumber will vent it. Relocating the plumbing at a kitchen sink is estimated at $350 to $900 in Sydney for 2027, before floor repairs. Checking the old drain with a camera first can show whether it is sound enough to join.

Trades That Work Alongside a New Sink

For Trades & Contractors - NSW

Plumbers who fit kitchen sinks and connect appliances can browse current work on the NSW job leads board, along with plumber jobs in NSW and emergency plumber jobs.

Ready to Install a New Kitchen Sink?

Post your job and compare quotes from licensed NSW plumbers for sink swaps, undermount sinks and new sink positions.

Get Free Plumber Quotes

About This Guide

This guide is general information only, and NSW rules, product details and prices can change. Confirm requirements with Building Commission NSW, SafeWork NSW for engineered stone, your owners corporation where relevant, and a licensed plumber before work starts.

Reviewed by The Quote Yard Editorial Team

Published 18 November 2026 ·

How The Quote Yard Works

We connect you with independent local tradies and service providers, we don't perform any trade work ourselves. Tradies provide their own quotes directly to you. Always confirm licensing, insurance, and scope of work before engaging any provider.

All NSW tradies are required to hold appropriate licences. Verify at NSW Fair Trading.
Prices are 2027 estimates for New South Wales and exclude the sink, tap, cabinet repairs and regional travel. Undermount fitting, a new sink drain outlet and tap holes in existing benchtops are quoted per job.
Need work done? Get free quotes. Post a Job – It's Free