Adding a Garbage Disposal Unit?
Tell us about your sink, the cupboard below it and whether you are on sewer or septic, and we'll connect you with licensed plumbers near you.
Typical Costs (2027 Estimates)
These figures are 2027 estimates for NSW homes. Disposer replacement, jam clearing and a dedicated circuit for the unit are priced per job.
Garbage Disposal Installation Services NSW - Get Local Quotes
Garbage disposal units, also sold as food waste disposers, are small grinders fixed under the kitchen sink that wash food scraps into the drain as a fine slurry. Fitting one in NSW needs a licensed plumber for the sink and waste pipe and a licensed electrician for the power. InSinkErator's Australian instructions call for an earthed (safely grounded) 20 amp wall socket and fitting to AS/NZS 3500.2, the national drainage standard. The cupboard below the sink also needs room for the motor, the trap (the water-filled bend in the pipe) and any filter or bin already stored there. Homes on a septic tank need a council check first, since some NSW councils do not allow them on septic systems. InSinkErator also says a dishwasher should not drain through the disposer. Using 2027 estimates, a standard installation costs about $300 to $550, and a new power point under the sink about $150 to $300. Where the wall waste pipe sits too high for the unit, lowering or extending it adds about $300 to $800. A dedicated circuit (a cable feeding only the unit), replacement units and jam clearing have no published price range and are priced on quote. Fats, oil and grease still belong in the bin, as Sydney Water warns they harden inside pipes and cause blockages. Tenants need the landlord's written permission first, and strata owners should check their building's rules (by-laws). Afterwards, the plumber should give you a Certificate of Compliance, the written proof the work meets NSW rules, so keep it with the appliance warranty.
At a Glance - Garbage Disposal Installation in NSW (2027 Estimates)
| Job | 2027 Estimate (NSW) | Suits | Disruption | Paperwork to Keep |
|---|---|---|---|---|
| Disposer installation, standard job | $300-$550 | Homes on the sewer with a suitable sink | Sink out of use for part of a day | Certificate of Compliance and unit warranty |
| New power point under the sink | $150-$300 | Cupboards with no free socket | Electrician visit before the plumber | Electrical compliance paperwork |
| Waste pipe extension or new connection | $300-$800 | Wall waste set too high for the unit | Wall or floor opened | Tax invoice listing the pipe work |
| Dishwasher connection at the sink | $150-$350 | Machine draining beside the disposer | Same visit as the disposer | Tax invoice |
| Leaking under-sink connection repair | $150-$300 | Joints that drip after the work | Short visit | Tax invoice |
| Kitchen sink blockage, single fixture | $150-$400 | Slow drains cleared before fitting | Short visit | Tax invoice |
| Under-sink water filter installation | $250-$500 | Filters sharing the same cupboard | Same visit if planned | Invoice and filter warranty |
| Disposer replacement or jam clearing | Priced on quote | Failed, noisy or jammed units | Depends on the mounting system | Tax invoice |
Cost Depth: What Moves a Disposer Installation Price
The height of the existing waste pipe and the power supply in the cupboard decide much of the price. A standard installation is estimated at $300 to $550, and lowering or extending the waste pipe adds about $300 to $800.
Electrical work is billed by the electrician. A new power point under the sink is estimated at $150 to $300, and no NSW price range exists for a dedicated disposer circuit, so that part is quoted on the length of cable needed.
All figures are 2027 estimates for NSW. Benchtop drilling, cabinet changes and regional travel can add to the final amount.
How a Garbage Disposal Unit Works Under the Sink
Each disposer bolts to the underside of the sink outlet, so food scraps drop straight from the bowl into a grinding chamber below. Inside the chamber a motor spins a plate, and the scraps are pressed against a fixed ring until they are small enough to flow away with water. The ground waste then leaves through a short outlet pipe into the trap and on to the household drain. Abey describes the result as a slurry, a watery mix of fine particles, that is carried through the sewage system to the treatment plant. Nothing is stored inside the unit once the water has run through it. The motor only turns while the unit is switched on, and it needs water flowing every time it grinds.
Every unit has two connections that need different licensed trades. The plumbing side covers the mounting ring at the sink outlet, the outlet pipe and the trap, which is the water-filled bend that stops sewer smells rising into the kitchen. On the electrical side sit the power supply and any switch used to start the motor. Plumbers and electricians may visit on different days, so the booking order matters. Other kitchen jobs can be added to the same plumbing visit, and you can compare them through our plumbing services page.
InSinkErator makes the Evolution Series of food waste disposers, sold for Australian kitchens. Abey makes the Enviro-Green Waste Machine, which takes fruit and vegetable scraps, seafood and bones, according to its maker. These were the only two disposer makers we could confirm on their own Australian websites when this guide was written. Both brands are sold through plumbing and appliance stores, so the plumber may supply a unit or fit one you have bought. Check which option the quote assumes before comparing prices. Any unit you supply yourself still needs to suit your sink, your cupboard and your drain.
Checking Your Sink and Cupboard Before You Buy
Start with the sink outlet, the hole in the bottom of the bowl where the plug and strainer sit now. The disposer replaces the existing strainer waste, the plug-hole fitting, with its own mounting flange, a metal ring that clamps to the sink, so the outlet must suit the unit's fitting. InSinkErator says its Evolution models can be fitted to most sinks in new or existing kitchens. Thin pressed stainless sinks, thick fireclay (glazed ceramic) sinks and composite sinks can each need a different flange or seal, so give the plumber the sink model number. If the sink itself is being replaced, plan both jobs together through kitchen sink installation so the new bowl suits the disposer from the start.
Double bowl sinks raise a second question about which bowl takes the unit. Put the disposer under the bowl you use most for scraps, while the other bowl drains through its own waste into a shared trap arrangement. Oliveri makes the Apollo range of stainless steel sinks in single, double and 1 and 3/4 bowl layouts, and the layout decides how the pipes can be joined. Your plumber can check whether the second bowl's waste can join the disposer's outlet pipe without water backing up into the other bowl.
Cupboard space is the next limit, because the motor hangs well below the sink outlet. Measure the clear height from the bottom of the sink to the cupboard floor, and the width between any pipes, valves and shelves. Unit sizes differ between models, so compare each maker's published dimensions with your measurements before you buy. Leave room for the trap below the unit, since the drain connection must sit lower than the disposer outlet. Oliveri also makes Puro Care sinks, a range designed for accessible kitchens, and a shallow bowl or a knee space under the sink can leave little room for a motor. Where space is tight, the plumber can say whether a smaller model would fit before you spend anything.
Measurements to Take Before Buying a Disposer
The clear height from the underside of the sink to the cupboard floor, and the inside width of the cupboard. The make and model of the sink, the size of its outlet and whether it is a single or double bowl.
The height of the wall waste pipe above the cupboard floor, since the drain connection must sit below the disposer outlet. The position of any power point, filter, boiling water unit or bin already in the cupboard.
Photos of the cupboard with the doors open help each plumber spot problems before quoting.
Sewer, Septic and Council Rules in NSW
Homes connected to the town sewer can send ground food waste down the drain with other kitchen water. According to InSinkErator's Australian and New Zealand instructions, the product may need approval from the relevant regulator or sewerage operator, so check before you buy. In Greater Sydney the sewer operator is Sydney Water, while in a number of regional towns the local council runs water and sewer services. Sydney Water's general advice on its website is to keep food scraps out of sinks with a strainer and to compost them or put them in the bin. We found no Sydney Water statement for or against household disposers, so check with your plumber whether your local operator has any rule.
Septic tanks are a different matter, and some NSW councils say so plainly. Nambucca Shire Council's septic maintenance fact sheet states that garbage grinders are not permitted to be installed on septic systems. Edward River Council's fact sheet on running an on-site sewage system tells owners not to use garbage disposal units or put food scraps down the drain. Septic tanks rely on solids settling and breaking down slowly, and extra food solids add to the load the tank must handle. If your home is not on the sewer, contact your council before buying a unit, and keep its written answer. Buying first and asking later can leave you with a unit you are not allowed to use.
Councils approve and regulate septic and other on-site sewage systems in NSW, so the council that issued your approval to operate, the permit for the system, sets the conditions. Aerated wastewater treatment systems, a type of on-site system with a pump and blower, also have service conditions set through the council. For pump-outs, inspections and repairs, see the local price ranges in our septic tank services guide. Where the council will not allow a disposer, a kitchen caddy for food scraps and a compost bin handle the same scraps without loading the tank.
Power Under the Sink: The Electrician's Part
Disposers are mains-powered appliances, so each one needs a power supply inside the sink cupboard. InSinkErator's Australian instructions say to connect to a 20 amp earthed wall socket using a 20 amp cable. Earthed means the socket is connected to the home's earth wire, which gives stray electricity a safe path away from anyone touching the unit. The same instructions say all plumbing and electrical work must be done by a qualified tradesperson. Adding or moving a socket is licensed electrical work, so book power point installation with a licensed electrician before the plumber comes.
Some kitchens already have a socket under the sink for a dishwasher or a boiling water unit. Check its rating and whether it is free, since a double adaptor or power board in a damp cupboard is a poor substitute for a proper outlet. For 2027, a new power point under the sink or in the next cabinet is estimated at $150 to $300. The electrician can also say whether the circuit feeding that socket has enough spare capacity for another motor.
Socket position matters as much as its rating. Place it to one side of the cupboard, away from the trap and the waste joints, so a drip cannot land on the plug. The plug should be easy to reach, so the unit can be switched off and unplugged before anyone works on it. Give the electrician the disposer model and its cord length so the socket ends up within reach of the motor.
Some kitchens need a dedicated circuit, which is a cable from the switchboard that feeds only one appliance. We found no NSW price range for a disposer circuit, so expect it to be quoted on the cable length and the space on your switchboard. For comparison, a dedicated dishwasher circuit is estimated at $250 to $400, though a disposer circuit may cost more or less. Request the circuit, the socket and any safety switch work, meaning the device that cuts power if current leaks, as separate lines on the electrician's quote. If your switchboard is old or full, mention it at the same visit, and our electrical services page lists the related jobs.
Air Switches, Wall Switches and Benchtop Buttons
Every disposer needs a way to start and stop the motor, and there are three common choices. Some models have a built-in switch, others plug into a wall switch, and some use an air switch with a push button on the benchtop or sink. An air switch sends a puff of air down a small tube to a switch box under the sink, so no electric current reaches the button. InSinkErator lists a built-in air switch in polished chrome as an accessory for its range. The button needs a hole in the sink's flat rim or the benchtop near the tap.
The maker's Australian instructions describe mounting the button through a 33 mm hole in the sink or a hole drilled in the benchtop. Some stainless sinks have a spare tap hole that can take the button, which saves drilling. Drilling a stone benchtop is a job for the stonemason, and we found no NSW price range for it, so it is priced on quote. Benchtops made of engineered stone carry extra dust rules when cut or drilled, and SafeWork NSW sets those rules. Laminate and timber benchtops can be drilled on site with the right hole saw. Choose the button position before any drilling, since a hole in stone cannot be moved later.
Wall switches are the other common choice, fixed to the wall or the cabinet near the sink. InSinkErator says any wall switch must show on and off markings and be installed by a qualified tradesperson. Place the switch where a young child cannot reach it easily, but where an adult can turn the unit off quickly. Talk through the switch type before the electrician arrives, because it changes where the cable and socket go.
Garbage Disposal Installation Prices for 2027
These 2027 estimates for NSW come from Quote Yard's NSW plumbing and kitchen price pages. Standard waste disposal unit installation is estimated at $300 to $550, and the source page counts a basic unit, mounting, the plumbing connection and coordinating the electrician in that figure. Unit prices vary with motor size, sound insulation and warranty length, so check whether the unit is included before comparing quotes. Electrical work, any new waste pipe and any changes to the sink or benchtop are separate items. Regional jobs can add travel time, and regional hourly rates are estimated at $70 to $150.
| Job | 2027 Estimate (NSW) | What Drives the Price |
|---|---|---|
| Plumber call-out fee (business hours) | $80 to $150 | Distance, time of day and whether the first hour is included |
| Plumber labour (business hours) | $90 to $180 an hour | Old waste fittings, tight cupboards and extra work found on the day |
| Disposer installation, standard job | $300 to $550 | Unit size, whether the unit is supplied, sink type and access |
| New power point under the sink (electrician) | $150 to $300 | Cable route, wall type and distance from the switchboard |
| Dedicated dishwasher circuit, for comparison (electrician) | $250 to $400 | Switchboard space and cable length |
| Waste pipe extension or new waste connection | $300 to $800 | Wall or slab material and how far the pipe must move |
| Dishwasher connection at the sink | $150 to $350 | Hose position, spigot fitting and cupboard space |
| Leaking under-sink connection repair | $150 to $300 | Which joint has failed and the parts needed |
| Kitchen sink blockage, single fixture | $150 to $400 | Grease build-up and how far down the line it sits |
| Disposer replacement, jam clearing or a disposer circuit | Priced on quote | Model, mounting system, cable length and access |
Plumbers' call-out fees in business hours are estimated at $80 to $150 across NSW, and hourly labour at $90 to $180. After-hours work is estimated at $150 to $250 an hour, so plan the installation for a weekday. Where the existing waste outlet sits too high for the unit, extending the waste pipe or making a new waste connection is estimated at $300 to $800. That cost can be larger than the installation itself, which is a good reason to measure the waste height before buying. For the rest of the standard rates, see our NSW plumber pricing guide.
Some costs only appear once the old waste is off and the cupboard is empty. Replacing an isolation valve, the small shut-off tap under the sink, that will not close properly is estimated at $100 to $220, and new flexible hoses for the tap at $30 to $60 a pair. If a joint fails during the work, a leaking under-sink connection repair is estimated at $150 to $300. Agree in writing how any extra pipe or valve work will be charged, so the final bill has no surprises. Should the job grow into wider kitchen changes, compare the figures in our kitchen plumbing cost guide. Keeping the job to the disposer alone is the simplest way to stay within the quoted price.
Where These Price Bands Come From
The installation, waste extension, dishwasher connection, connection repair and under-sink filter figures come from Quote Yard's NSW kitchen plumbing price pages. The power point figure comes from our dishwasher installation guide, and the dishwasher circuit figure from our kitchen electrical price page.
Call-out, hourly, regional and after-hours rates come from our NSW plumbing price pages. No NSW page gave a separate figure for replacing a disposer, clearing a jammed unit, a disposer circuit or a benchtop button hole.
All figures are 2027 estimates for NSW homes. Jobs without a published band are priced on quote.
Connecting the Disposer to the Waste Pipe
The plumbing standard for drains inside a home is AS/NZS 3500.2, the part of the Australian plumbing standards that covers the pipes carrying waste water from sinks, basins and toilets to the drain. InSinkErator's Australian instructions say its disposers must be installed to that standard. From the unit, a short outlet pipe leads to the trap, and from there the wall or floor waste carries everything to the drain. Each joint should be tested with running water before the cupboard is closed up.
The fall of the waste pipe, meaning how steeply it slopes down, matters more with a disposer than with an ordinary sink. The maker's instructions call for the drain line to fall at least 6.4 mm for every 0.3 metres of pipe length. They also warn that the drain connection must be lower than the disposer outlet, or standing water can cause corrosion or leaks. In older kitchens the wall waste can sit too high for a disposer, which is why some jobs need the waste pipe lowered. Lowering a waste pipe in a brick wall or a concrete slab takes longer than a simple fit, so expect it on the quote as its own line.
Vinidex makes PVC DWV pipe systems, short for drain, waste and vent, which carry used water from sinks to the drain. Iplex makes DWV pipes and fittings as part of its PVC non-pressure range. Pipes like these are joined with solvent cement, a glue that fuses the plastic, or with rubber ring seals, depending on the fitting. The plumber chooses fittings that suit the existing pipe size, so the new section lines up with the old drain. Old metal or earthenware waste pipes in older homes may need replacing where they meet the new work.
Older kitchens can have another problem behind the cupboard back. The NSW Government warns that homes built before 1990 may contain asbestos, and it lists kitchen splashbacks among the places it can be found. If a waste pipe has to pass through an old wall sheet or splashback, have the material tested before anyone cuts or drills it. SafeWork NSW sets the rules for handling and removing asbestos at home, including who may do the work.
The branch line is the pipe that carries water from the kitchen to the main drain, and it can hold grease and old sludge from years of use. Disposers send more solids along that pipe, so a branch line that is already slow will get worse. If the sink drains slowly now, book blocked sink and basin repairs first so the line is cleared before the unit goes in. Clearing a single kitchen sink blockage in business hours is estimated at $150 to $400. Where several fixtures drain slowly at once, the problem may lie further down, so look at blocked drain clearing for the wider system. Clearing the line first, with hydro jetting drain cleaning where old grease has built up, also gives the plumber a clean starting point for the new connection.
Dishwashers and Disposers in Australian Kitchens
Disposers sold in some countries have a side inlet so the dishwasher can drain through the unit. InSinkErator's installation instructions for Australia and New Zealand say plainly not to connect a dishwasher to the disposer's dishwasher inlet. The same document notes that the inlet plug cannot be replaced once it has been knocked out. Leave that plug in place, and have the plumber drain the dishwasher through the sink waste in the usual way.
The dishwasher's drain hose still needs a connection under the sink, such as a spigot, a short pipe outlet, on the trap or waste pipe. Dishwasher makers set out how high the hose must loop before it drops into the drain, so dirty water cannot flow back into the machine. Bosch makes dishwashers for Australian kitchens, and Miele makes freestanding, built-under and integrated dishwashers. Smeg makes freestanding, built-in and partially integrated dishwashers, and each maker's installation guide sets its own hose and power requirements. Keep the dishwasher manual handy on installation day so the plumber can check those details. If the pipes bang when the dishwasher fills, ask about water hammer and noisy pipe repair while the cupboard is open.
For 2027, a dishwasher connection at the sink is estimated at $150 to $350. Fitting a disposer and reconnecting a dishwasher in the same visit saves a second call-out fee. The cupboard can get crowded with a disposer, a dishwasher drain hose, two isolation valves and a power point all in one space. For a new machine or a new position, see our dishwasher installation guide before booking. Request a quick sketch from the plumber showing where each part will sit before work starts. Labelling the two isolation valves also helps anyone who needs to turn the water off later.
Choosing a Unit: Motor Size, Noise and Warranty
Disposers are sold by motor size, given in horsepower, and by how many grinding stages they use. InSinkErator's Evolution 200 specification lists a 0.75 horsepower motor for 220 to 240 volt supply and three-stage grinding. Motor size is one of the main differences between models, so match it to how much and how often you cook. Noise varies between models, and InSinkErator lists multi-layer sound insulation and a quiet sink baffle, a cover in the sink opening, on the Evolution 200. Read the maker's specification sheet, not only the box, to compare models fairly.
Warranties also vary widely from one model to the next. InSinkErator's Evolution 200 specification gives a six year parts and service guarantee. Its Australian consumer brochure lists shorter in-home warranties for smaller models, from three to five years. Warranty cover can depend on installation in line with the maker's instructions and local plumbing and electrical rules, so keep the installer's paperwork. Register the unit with the maker after installation if the maker offers registration.
Price, size and warranty all matter, but the right unit is one that fits your cupboard and suits how much you cook. Households that eat out several nights a week may never need a large motor. Families cooking every night with plenty of vegetable peelings may notice a smaller unit working harder. Measure first, shortlist two or three models, and check with each plumber which ones they install and why.
Replacing an Old or Failed Disposer
Like any appliance, a disposer wears out, and signs of trouble include a humming motor that will not spin, water leaking from the body, or slow draining. Humming with no grinding can mean something is jammed in the chamber, so switch off the power and follow the maker's manual to free it. Water leaking from the unit's body can mean internal seals have failed, and a plumber can tell you whether the unit needs replacing. Leaks at the joints, on the other hand, can be fixed by remaking the connection. We found no NSW price range for replacing a disposer or clearing a jammed unit, so both are priced on quote.
Replacement is quicker when the new unit uses the same mounting system as the old one. With a change of brand, the plumber may need to fit a new flange at the sink outlet and adjust the outlet pipe. Give the plumber the old unit's model number, which is on a label on the side or base of the motor. The old unit has to go somewhere, and our guide to appliance removal costs lists options for getting rid of it. If you are unsure whether to repair or replace, book appliance repairs to have the motor tested first. Compare the repair quote with the replacement quote before deciding.
Removing a disposer altogether is also an option if you no longer want one. The plumber takes the unit off, fits a standard strainer waste to the sink outlet and reconnects the trap. Afterwards the electrician can leave the socket for another appliance or disconnect it safely. Clark makes a stainless steel basket waste grate, an example of the strainer fittings that can go back into a sink outlet. Other small fixes under the sink are listed in our guide to bathroom and kitchen fixture repairs.
What Should and Should Not Go Down a Disposer
Disposers are built for food scraps, and InSinkErator says packaging should never go into one. Its Australian instructions list clam or oyster shells, caustic drain cleaners, glass, china and plastic as items to keep out. InSinkErator also advises against very stringy or fibrous foods such as celery. Its consumer brochure says never to use cleaning solvents or chemicals of any kind in the unit. Cutlery, bottle caps and twist ties dropped by accident can also jam the grinding chamber.
InSinkErator's brochure says bones can be ground, along with other food scraps. Run a moderate stream of cold water while the unit is grinding, as the maker advises. Cold water hardens any fat so it can be broken up and carried away, according to the brochure, which says never to use warm water. After grinding, turn the unit off and keep the water running for 10 to 15 seconds to flush the drain line, as the maker's instructions direct.
Using the unit well also protects the pipes beyond it. Feed scraps in gradually, not in one large handful, so the motor is not overloaded. Keep a small caddy by the sink for anything that should not go down, such as shells, packaging and large amounts of fat. Teach everyone in the house which items belong in the bin, especially children and guests. Covering the opening with a sink stopper when the unit is not in use stops small objects falling in.
Fats, Oil and Grease Still Belong in the Bin
Grinding food does nothing to stop fat hardening further down the pipe. Sydney Water says fats, oils and grease should never be poured down the drain, because they cool and harden in wastewater pipes. It warns that hardened fat can combine with wipes and other unflushable waste to form large blockages called fatbergs. InSinkErator gives the same advice, saying never to pour grease, oil or fat down the disposer or any drain. Wipe greasy pans with a paper towel and put the towel in the bin before washing up. Bacon fat, roasting juices and curry oils all count as grease, even while they still look runny in the pan.
Sydney Water suggests storing leftover cooking oil in a sealed container and placing it in the garbage bin. It also notes that cooking oil can be taken to a Community Recycling Centre. Only water, detergent and soap should go down sinks, according to Sydney Water's blockage advice. Some councils offer food organics and garden organics collections, known as FOGO, which take food scraps in the green bin. If your council runs one, you can use the bin and the disposer side by side, sending tougher scraps to the bin. Ask your council whether it runs one, since collection services differ between council areas.
Owners are responsible for the private wastewater pipes on their property, up to the point of connection, where the private pipe joins Sydney Water's main. That point can sit outside the property boundary, so a blockage near the street may still be the owner's to fix. Sydney Water's fault line, 13 20 90, can help work out whether a blockage is in its pipes or yours. Blockages in private pipes need a licensed plumber, and wastewater overflowing inside the home is a job for an emergency plumber.
Smells, Leaks and Hoses Under the Sink
Smells usually start when scraps sit in the chamber, especially when the unit is run with too little water. Running cold water for the full flush time after each use clears leftover waste from the chamber. Never pour bleach, caustic cleaners or drain chemicals into the unit, since the maker warns against them. Persistent smells that return soon after cleaning may come from the drain, a dry trap or a cracked pipe, not the disposer. In that case, look at sewer smell and drain odour repairs for the other possible causes.
Leaks under the sink show up as damp cupboard floors, swollen chipboard or a musty smell. Check the mounting ring, the outlet pipe joint and the trap first, since these are the points the plumber connected. The flexible hoses that feed the tap sit in the same cupboard, and a disposer job is a good time to check them for rust or fraying. Worn hoses should be swapped by a plumber, so book flexible hose replacement if you see damage.
Vibration is another reason to check joints after the first few weeks. The motor shakes slightly when it starts, and a loose clamp or mounting ring can work free over time. Look under the sink once a month for drips while the unit runs, using a torch. Catching a small leak early costs far less than replacing a rotted cupboard floor. For leaks you cannot trace, arrange water leak detection so a plumber can find the hidden water. Keep a note of when each drip appears, since the timing helps the plumber narrow down the source.
Sharing the Cupboard With Bins, Filters and Storage
The sink cupboard tends to be the busiest space in the kitchen, holding cleaning products, a bin and sometimes a water filter. Franke makes the 300-60 and 300-45 Duo Sorter waste bins, which fit inside kitchen cabinets to separate rubbish from recycling. Puretec makes kitchen undersink filters, and these units also need room on the cupboard floor or wall. Plan where each item will go before the disposer arrives, so nothing has to be moved twice. Under-sink water filter installation is estimated at $250 to $500, and our water filter installation page covers that job.
Pull-out bins and drawers may need trimming or moving to clear the motor. Cabinetmakers can cut a new shelf or move a drawer runner so the unit has space. Leave clear access to the isolation valves, the small shut-off taps under the sink, so they can be turned off in a hurry. Keep chemicals away from the motor and the electrical socket. Placing a drip tray on the cupboard floor makes small leaks easier to spot.
Tapware can change the space too, since pull-out mixers have a hose and weight that hang under the sink. Dorf makes the Vixen retractable sink mixer in a lead-free version, and its hose loop needs room to move freely. Fienza makes sink mixers and pot fillers, and the mixer type decides how much of the cupboard its hoses use. If the tap is changing at the same time, add tap and mixer installation to the same booking.
Apartments, Strata Buildings and Rented Homes
Strata buildings are run by an owners corporation, the body formed by every lot owner, which looks after the parts of the building that all owners share. Those shared parts, called common property, can include the drainage stacks, the vertical pipes that carry waste down from every apartment. By-laws are the building's own rules, and some deal with changes to plumbing or appliances. Read your by-laws and write to the strata manager before booking a disposer, and keep the reply. For plumbing questions that affect shared pipes, see our strata and body corporate plumbing guide.
Upper floor apartments share stacks with the units below, so a blockage can affect neighbours. Some buildings already have problems with grease in the kitchen stacks, and the strata committee, the owners elected to handle day-to-day matters, may be cautious about extra solids. Give the strata manager the model, the installer's licence number and a note on how the unit connects to your private waste pipe. Clear information helps the committee give an answer without delay.
Renters in NSW may alter a rented home only where the lease permits it or the landlord has agreed in writing. The list of minor changes a landlord cannot unreasonably refuse, set out on nsw.gov.au, does not include kitchen appliances or plumbing. Write to the landlord or agent, name the licensed plumber and electrician, and agree who pays and what happens at the end of the lease. Disputes about changes can go to the NSW Civil and Administrative Tribunal, also called NCAT. Landlords planning a unit for a rental can bundle it with other jobs through rental property maintenance. Keep a copy of the written permission with your lease papers in case questions come up later.
Licences, WaterMark and the Paperwork
In NSW, plumbing work needs a licence regardless of its cost, and that includes connecting a disposer to the sink and drain. Plumbing licences are regulated by Building Commission NSW, which takes calls on 13 27 00. Search the plumber's name or licence number on the Verify licence register and confirm the licence is current before any work begins. Sydney Water limits do-it-yourself plumbing to changing a tap washer, and it says all other plumbing jobs need a licensed plumber. Electrical work on the socket or circuit needs a licensed electrician, which is a separate licence from the plumber's. Both trades carry their own licence cards, so you can see each one on the day of the work.
Plumbing products such as waste fittings, traps and flexible hoses need WaterMark certification, a mark showing the product meets Australian plumbing requirements. The Australian Building Codes Board runs the WaterMark scheme, and its website sets out how products are certified. The Plumbing Code of Australia sets the performance rules for plumbing work, and the AS/NZS 3500 series gives accepted ways to meet them. Current editions of those standards are listed by Standards Australia. Have the plumber confirm that every fitting used carries the right certification.
A Notice of Work is a form a plumber lodges to tell the regulator that plumbing work is planned. Most plumbing work needs one, though emergency work and minor work such as replacing tapware are exempt, so ask the plumber which applies to your job. The Certificate of Compliance is the plumber's written statement that the work meets the rules, issued at the end of the job. Your copy comes to you as the person who booked the job, so file it with the appliance manual and warranty. For larger kitchen projects worth more than $5,000 including GST, NSW law calls for a written contract and caps the deposit at 10 per cent. Plumbers in Sydney, the Illawarra, the Blue Mountains and the Newcastle and Hunter area lodge these documents through an online system called MyInspections, while elsewhere the local plumbing regulator handles them.
Getting Comparable Disposer Quotes
Quotes are easiest to compare when each plumber prices the same job. Send the same details to everyone, including the sink model, the disposer model if you have chosen one, and photos of the cupboard. Say whether there is already a power point under the sink, and whether a dishwasher drains there. Mention whether the home is on sewer or septic, and whether it is a house, a strata unit or a rental. Post the job once through our kitchen plumbing page and up to three local plumbers can quote.
Details to Include in Your Quote Request
Your suburb, the sink make and model, whether it is a single or double bowl, and the benchtop material. The disposer model, or the size and budget you have in mind if you want the plumber to supply one.
Photos of the cupboard, the waste pipe and any existing socket. Whether a dishwasher, filter or bin shares the cupboard, and whether the home is on sewer or septic.
The more detail you send, the closer the quotes will be to the final bill.
Each quote should show the unit price separately from the labour, so you can see the cost of the disposer itself. It should also list the mounting, the trap and outlet connection, and any waste pipe changes. Electrical work belongs on the electrician's quote, unless the plumber arranges both trades and says so in writing. Check whether removing and disposing of an old unit is included. Confirm who registers the warranty and who returns if a joint leaks in the first weeks. Quotes that leave these points out are hard to compare, even when the totals look close.
Timing matters as much as price, especially in a busy kitchen. The sink is out of use while the plumber works, and the power must be in place before the unit can be tested. Book the electrician first, or have the plumber coordinate both trades on the same day. Splitting the job over two visits may cost an extra call-out, so ask about this when comparing quotes.
What to Look Out For in Garbage Disposal Installation Quotes
Watch for a quote that does not say whether the disposer is included. One low price may cover labour only, while a higher one may include a mid-range unit, so the two cannot be compared without that detail. Be wary of any installer who offers to wire the power point as well without holding an electrical licence. Check both licences on the Verify register before agreeing to anything. Quotes that skip the waste height check may lead to a second visit to lower the pipe.
Be cautious about anyone who suggests connecting the dishwasher through the disposer inlet. InSinkErator's Australian instructions say not to do that, and its warranty excludes units not installed in line with the maker's instructions. Equally, a plumber who never mentions septic or strata rules may not have asked about your home. Look for written answers to your questions, a clear total, and a statement that a Certificate of Compliance will be issued. Avoid paying the whole amount up front, and agree on any deposit in writing.
Pressure to buy a particular unit on the spot is another warning sign. A fair quote lets you choose between the plumber's supply and your own unit, with the labour shown either way. Check that the quote includes testing every joint with running water before the plumber leaves. Turn down any quote that has no business name, licence number or written scope of work.
Looking After the Unit Once It Is Installed
Run the disposer with cold water every time and let the water flow for the flush time the maker states. Run it regularly with water, since scraps left sitting in the chamber can start to smell. Clean the splash guard, the rubber flap at the top of the sink outlet, with a brush and mild detergent. Never put your hand into the chamber, even with the power off, and follow the maker's manual to free a jam. Store the manual where everyone can find it.
Check under the sink every few weeks during the first months for drips at the joints. Slow draining after installation can mean scraps are building up in the pipe or the waste pipe does not slope enough, which a drain camera inspection can confirm. Call the installing plumber back as soon as you notice a problem, and describe what you saw. Photos of any drip or water mark help the plumber judge the cause before arriving. Running the unit for a minute with the cupboard door open makes small drips easier to see. If problems continue, a plumber found through our Sydney plumber listings or a local one can inspect the drain.
A sink strainer is still useful alongside a disposer, especially for items that should never be ground. Oliveri makes a colander that sits in its Monet main bowl, one example of a sink accessory that catches food before it reaches the outlet. Packaging, shells and fat can go in a bin caddy close to the sink. If a council FOGO bin is available, use it for the scraps that are hard for your unit to grind. Habits like these lower the chance of a blocked branch line and an after-hours call-out.
Disposer Plumbers in Every NSW Region
We connect homeowners, landlords and strata owners with licensed plumbers throughout New South Wales for new garbage disposal units, replacement units and the waste pipe work behind them. Post your job once and compare quotes from plumbers who work in your area.
▶ Sydney Inner City 18 areas
▶ Greater Sydney 25 areas
Western Sydney
South Western Sydney
Northern Sydney
The Hills District
Inner West
St George
▶ Sydney Coastal 23 areas
Northern Beaches
Eastern Suburbs
Harbour Suburbs
Sutherland Shire
▶ Hunter & Central Coast 19 areas
Central Coast
Hunter Valley
Port Stephens
▶ Illawarra & South Coast 18 areas
Illawarra
Shoalhaven
Sapphire Coast
▶ North Coast 19 areas
Mid North Coast
Coffs Coast
Northern Rivers
▶ Blue Mountains & Highlands 17 areas
Blue Mountains
Southern Highlands
▶ Regional NSW 21 areas
Central West
Riverina
New England
Far West
Garbage Disposal Installation FAQs
Can any plumber fit a garbage disposal unit in NSW?
Do I need a power point under the sink for a disposer?
Can I install a disposer if my home is on a septic tank?
Can the dishwasher drain through the disposer?
How much does it cost to install a garbage disposal unit in NSW?
Will a disposer fit my existing kitchen sink?
What should never go into a garbage disposal unit?
Can I have a disposer fitted in a rental or strata apartment?
How long does a garbage disposal unit last?
What paperwork should I get after installation?
Trades That Help With a Disposer Installation
Related Services
For Trades & Contractors - NSW
Plumbers who fit food waste disposers and other under-sink appliances can find new work on the NSW job leads board, along with plumber jobs in NSW and emergency plumber jobs.
Ready to Add a Garbage Disposal Unit?
Post your job and compare quotes from licensed NSW plumbers for disposer installation, replacement units and waste pipe changes.
Get Free Plumber QuotesAbout This Guide
This guide is general information only, and NSW rules, product details and prices can change. Confirm requirements with Building Commission NSW, your council if the home is on a septic system, your owners corporation where relevant, and a licensed plumber and electrician before work starts.
Looking for more services across New South Wales? View all available trade services.
Reviewed by The Quote Yard Editorial Team
How The Quote Yard Works
We connect you with independent local tradies and service providers, we don't perform any trade work ourselves. Tradies provide their own quotes directly to you. Always confirm licensing, insurance, and scope of work before engaging any provider.