Sewer Smell in the House?

Tell us which rooms smell, when it happens and whether any fixtures are rarely used, and we'll connect you with licensed plumbers near you.

Get Free Plumber Quotes

Typical Costs (2027 Estimates)

Call-out and diagnosis visit$90-$160
Plumber hourly rate (business hours)$90-$180/hr
Toilet pan seal or connector refit$200-$550
Single fixture blockage cleared$150-$400
Camera added to the visit$200-$450
Laundry drain and trap replaced$200-$500
After-hours hourly rate$150-$250/hr

These figures are 2027 estimates for NSW homes. Vent repairs, trap primers, drain repairs found on camera and regional travel are priced per job.

Sewer Smell & Drain Odour Repair Services NSW - Get Local Quotes

A sewer smell inside a home means air from the drains is getting past a barrier meant to hold it back. Each sink, basin, shower and toilet has a trap, a bend that holds water, and that water seal blocks gas rising from the sewer. Smells come back when a trap dries out in a spare room, a toilet seal fails, a vent pipe is damaged or a drain cracks under the floor. A rotten egg smell near a gas appliance is different: leave the building, call 000, then ring the gas supplier on your bill. For a sewer smell, a licensed plumber checks the traps, the toilet base, the vent pipes, the outdoor drain grate called a gully and the pipes, with a camera if needed. Using 2027 estimates for NSW, a call-out and diagnosis visit costs about $90 to $160, and a toilet pan seal refit about $200 to $550. Adding a camera to the visit runs about $200 to $450, and the footage shows if a pipe has cracked or a joint has moved. Owners are responsible for private wastewater pipes up to and including the point of connection, where they join the sewer main. In its area, Sydney Water owns the main and the junction fitting, and councils run sewer services in many regional towns. Where the smell is only in a spare bathroom or laundry, run water into each fixture first, as refilling a dried-out trap costs nothing. Dishwashers and washing machines can smell too, so check their filters before you book. Repairs to drains and fixtures are licensed work in NSW, so the plumber should finish with a Certificate of Compliance, a form showing the work meets the rules.

Plumbers Who Trace Drain Smells Across NSW

Licensed plumbers find and fix sewer smells in houses, townhouses, rentals and strata units across Greater Sydney, the Hunter, the Illawarra, the Central Coast and regional NSW. Describe the smell once and we can put you in touch with up to three local plumbers for quotes you can compare.

Get Free Quotes

At a Glance - Sewer Smell and Drain Odour Repairs in NSW (2027 Estimates)

Job 2027 Estimate (NSW) Common Smell Source Where the Plumber Works What You Receive
Call-out and diagnosis visit $90-$160 Finding where a smell starts Fixtures inside, gully and vents outside Findings and a repair quote
Toilet pan seal or connector refit $200-$550 Smell or damp around one toilet Toilet lifted off the floor New seal and pan reset
Single fixture blockage cleared $150-$400 Slow, sour smelling sink, basin or shower Fixture trap or drain pipe Tax invoice
Laundry drain and trap replacement $200-$500 Cracked or leaking laundry waste Behind the machine or under the sink New trap and drain pipe
Camera added to a clearing visit $200-$450 Checking a drain for cracks and open joints Inspection opening or gully Footage and short summary
Camera inspection with written report $350-$800 Planning a drain repair Any opening on the line Video and written report
Overflow relief gully blockage (emergency) $350-$900 Sewage rising in the outdoor gully The gully and drain beyond it Tax invoice
Drain section dug up and replaced $1,500-$4,500 Broken pipe found on camera Digging down to the pipe Certificate of Compliance

Cost Depth: From Free Fixes to Drain Repairs

Refilling a dry trap or floor drain costs nothing and fixes a smell in a spare bathroom or laundry. Failed toilet seals sit in the middle of the range, while a cracked drain under a slab needs digging or relining, which means lining the old pipe from inside.

Paying for a proper diagnosis first can save money on the repair. Together, a call-out of about $90 to $160 and a camera at about $200 to $450 can confirm the cause before you agree to a repair costing thousands.

All figures are 2027 estimates for NSW. Digging, relining, roof access and remote travel are quoted separately.

Why a House Starts to Smell Like Sewage

Every drain in a house is joined to a sewer main or a septic system, and the air inside those pipes carries the smell of waste. Plumbing is built so that this air stays in the pipes and leaves through vent pipes above the roof line. Under the Plumbing Code of Australia, the national rules for plumbing work, plumbing for toilets, sinks and drains must stop foul gases from entering buildings. When a sewer smell reaches a bathroom, kitchen or laundry, one of the barriers that holds the gas back has failed. Each barrier fails in its own way, so the fix for one smell can be very different from the fix for another.

The first barrier is the trap under each fixture, which is a U or S shaped bend in the waste pipe. Water sits in the low part of the bend after every use, and that pocket of water is called the water seal. Gas from the drain cannot push through the water, so the room stays fresh while the trap stays full. Toilets carry their own trap moulded into the porcelain, which is why there is always water in the bowl. Floor wastes, the grated drains in bathroom and laundry floors, are trapped in the same way below the grate. Some showers and baths drain without a trap of their own into a nearby floor waste gully, a trapped fitting under the floor, which then holds the water seal for both.

The second barrier is the set of seals where pipes and fittings join. Each toilet sits on a rubber connector that seals it to the drain in the floor or wall behind it. Joints in the waste pipes under sinks, in wall cavities and under the house are sealed with glue or rubber rings. If any of these joints cracks or works loose, drain air can escape into a cupboard, a wall or the space under the floor. That smell then drifts into the house without any water being seen.

The third barrier is the vent system, which lets air move in and out of the drains. Vent pipes rise through the roof or run up an outside wall so that sewer air escapes high above windows and doors. Under the Plumbing Code, vents must limit the push and pull of air on trap water so that flushing and draining do not pull the water out of nearby traps. Blocked, broken or missing vents can let traps lose their water when a toilet is flushed or a bath empties. On its own network, Sydney Water also runs ventilation shafts, which let air enter and leave the wastewater system.

Smells can also come from outside the plumbing, which should be ruled out before booking a repair. Common outdoor sources listed by Hunter Water include mulch, fertiliser, decomposing plant or animal matter and stagnant water in creeks or dams. It also notes that heavy rain can cause sewer smells to rise through floor drains. Pump stations and treatment plants can release hydrogen sulphide, a gas with a rotten egg smell, though water utilities work to limit it. When the smell is only outdoors and spread across the street, ring the local water utility first.

Rotten Egg Smell Near Gas Appliances: Leave First

Household gas has no smell of its own, so a warning chemical is added to it before it reaches homes. According to the NSW Government, that added chemical makes gas smell a bit like rotten eggs. Sewer air can carry a similar smell, so a householder cannot safely tell the two apart by nose alone. Any rotten egg smell near a cooktop, oven, gas heater, hot water unit or gas meter should be treated as a possible gas leak.

If you smell gas, leave the building straight away and take everyone with you. Once outside, call 000, as the gas safety advice on the NSW Government website directs. Then ring your gas supplier, using the phone number printed on your gas bill. Do not use lighters or matches to look for the leak, and put out any naked flames on your way out if it is safe. Drain plumbers are the wrong people to call first, because gas leaks need emergency services and the gas supplier.

After the emergency is over, any repair to gas pipes or appliances needs a licensed gasfitter. Gasfitting is licensed work in NSW, alongside plumbing and draining, and the licence must cover gasfitting. Some plumbers hold both licences, which helps when a smell could come from either system. You can confirm what a licence covers by searching the tradesperson's name on the NSW licence register. Once the area is safe, book gas leak repairs for the pipework, or gas heater servicing when a heater smells as it lights.

Gasfitters use electronic detectors to find small leaks along pipes and fittings. Testo makes the testo 316-1 methane gas detector, which shows a yellow light above 200 parts per million of methane and a red light at much higher levels. Methane is the main part of natural gas, so a reading near a gas pipe helps the gasfitter find the leaking joint or valve. Handheld detectors do not replace the emergency steps above when the smell is strong or spreading.

Dry Traps in Spare Bathrooms, Laundries and Floor Wastes

A trap only works while it holds water, and that water slowly evaporates when a fixture is not used. According to Hunter Water, a rarely used drain can lose its water, breaking the seal and letting sewer odours in through toilets, floor drains or sinks. Guest bathrooms, holiday homes, granny flats and laundry floor wastes are places where this can happen. Homes left empty for several weeks can return to a smell in more than one room at once. The fix for a plain dry trap is free: run water into the fixture for a few seconds to refill the seal. Refill every fixture at once if you are unsure which one is causing the smell.

Floor wastes are the easiest traps to forget because nothing drains into them for days at a time. Shower floor wastes refill each time someone showers, but a laundry or toilet floor waste may only get water during a spill or a mop. Pouring a bucket of water into each floor waste from time to time keeps the seal topped up in rooms that see little use. If a floor waste smells again within a day of refilling, the water may be draining away through a crack or a leaking joint below. Laundry floor wastes hidden behind a washing machine are easy to miss, so move the machine or use a jug to reach them.

Some buildings have a trap primer, a device that tops up floor waste traps with a small amount of water. Galvin Engineering makes the Flowmatic electronic trap primer, which it describes as keeping a constant water seal in floor drain traps that are rarely used. Trap primers connect to the water supply, so fitting one is plumbing work that needs a licensed plumber. They suit floor wastes that almost never receive water, such as those in machinery rooms or bathrooms that sit unused.

Shallow or damaged traps under basins can also lose their water seal faster than they should. Holman makes standard P traps and S traps in 40 and 50 millimetre sizes, the common sizes for basins, sinks and laundry wastes. Nero Tapware makes bottle traps, a compact style of trap fitted below basins where the pipes are on show. Before blaming anything further down the drain, the plumber checks that the trap is the right size, that it holds water and that its joints are tight. Under Sydney Water's guidance, a confident householder may change a tap washer, but replacing a trap or waste is work for a licensed plumber.

Trap water can also be pulled out by the drains themselves when the plumbing is badly laid out. Missing or blocked vents, or fixtures added during a renovation without proper venting, can cause this effect. The signs include gurgling from a basin when a toilet is flushed, or a toilet bowl water level that drops after a bath drains. These faults need a plumber to look at the venting and pipe layout, not just refill the trap. Venting faults are found by watching the traps while other fixtures drain, which a plumber can do in a single visit.

Smells at the Toilet Base and Behind the Pan

Smells that stay close to one toilet, even when the bowl is clean, suggest a problem with the seal between the pan and the drain. The pan is the porcelain bowl, and it sits on a rubber connector or collar that pushes into the drain pipe. Gas can leak out around the joint if the pan has been knocked, the floor has moved or the seal has aged. A smell before any visible water is one of the first signs of a failed seal. Water marks, a loose pan or soft flooring around the base are further reasons to lift the pan and check the seal. Rocking the pan gently with your hand will show whether it has come loose from the floor.

To fix the seal, a plumber turns off the water, disconnects the cistern, the water tank behind the bowl, and lifts the pan off the floor. The old connector or collar is removed, the drain opening is cleaned and checked, and a new seal goes in. The pan is then set back in place, fixed down and sealed at the floor, and the plumber tests it with several flushes. Using 2027 estimates for NSW, a pan seal or connector refit costs about $200 to $550, depending on access and the toilet style. Damage to the drain opening under the pan can lift the price, because extra parts or tile work may be needed.

Newer toilets use connectors designed to fit straight into the drain without a separate collar. Caroma makes the Uni-Orbital connector, which fits directly into the drain pipe and lets the pan sit anywhere within a 50 millimetre radius. Back-to-wall and wall-hung toilets hide the connection behind the pan or inside the wall, which can add time to a seal repair. Where the pan is cracked or the flooring under it has rotted, plan for wider toilet repairs or a new suite.

Some toilet smells are not sewer gas at all but normal odours after use that linger in a small room. Geberit makes DuoFresh, an odour extraction unit built into the flush plate of its Sigma concealed cisterns, which sit hidden inside the wall. It draws air from the bowl through a filter and needs a 240 volt power connection, so an electrician is part of the job. Room exhaust fans do a similar job for the whole bathroom, so consider bathroom ventilation when smells hang around after showers. Neither product fixes a failed seal or a dry trap, so the plumbing should be checked first.

Blocked toilets can also smell before they overflow, because waste sits in the pan or the pipe beyond it. Slow flushing, bubbling and a high water level in the bowl are signs that the line is partly blocked. One of the most common reasons for sewer odour inside a home, according to Hunter Water, is a blocked toilet or sewer. Clearing a blocked fixture during business hours is estimated at $150 to $400 for 2027. If plunging does not clear it, compare plumbers for blocked toilet repair services before the pan overflows.

Roof Vent Pipes and Air Admittance Valves

Vent pipes are the open pipes you see poking through the roof or running up an outside wall to above the gutter. During its smoke tests, Sydney Water says, smoke coming out of private wastewater vent pipes is normal and shows the vents are working. Vents that have been cut short, crushed, capped or blocked can no longer carry sewer air safely away from the house. Nests, leaves and roof work that covers a vent outlet are among the faults a plumber looks for. Fixing them can be as simple as clearing the outlet or as involved as replacing a section of vent pipe on the roof. Roof work carries a fall risk, and SafeWork NSW sets the rules plumbers must follow when working at heights.

Vent faults show up in a few ways that householders can notice. Gurgling from basins or showers, slow draining across several fixtures and smells near windows close to a roof vent are all signs to report. Vent outlets that end close to a window, a deck or an air conditioning intake can let sewer air drift back inside. The plumber may need roof access, a ladder or a harness, which affects the time and price of the visit. Vent repairs have no published Quote Yard price range, so they are priced on quote from the call-out fee, the hourly rate and parts.

An air admittance valve is a one-way valve that lets air into a drain but closes to stop sewer gas getting out. Holman makes a 40 and 50 millimetre air admittance valve for drain, waste and vent systems. These valves are used where running a full vent pipe up through the roof is hard. Building Commission NSW, the plumbing regulator, has published an advisory note on how air admittance valves must be installed. If a smell is strongest at a cabinet holding one of these valves, a licensed plumber checks it and replaces it if needed.

Homes built before the late 1980s may have asbestos cement vent pipes or drains. SafeWork NSW lists sewer vents and cement pipes among plumbing items that can contain asbestos. Damaged asbestos cement should not be cut, drilled, broken or cleaned with high pressure water, so the plumber should test before working on it. If testing confirms asbestos, work on those pipes should follow SafeWork NSW rules for safe removal and disposal. Testing costs about $50 to $150 per sample in 2027, and you can book asbestos testing and inspection separately before repairs.

Cracked or Leaking Drains Under the House or Slab

When a smell is strongest under the floor, in a garage or near an outside wall, the drain itself may be leaking. Tree roots, ground movement, old clay joints and earlier repairs can crack drains or pull joints apart. Cracked sewer drains let sewer air and wastewater escape into the soil, and the smell can rise through gaps in the floor. Damp patches or sunken paving over a drain line are other signs to mention to the plumber. Tree roots can enter wastewater pipes through small cracks and then grow inside them, Sydney Water notes. Note where the smell is strongest before the visit, because that spot helps the plumber decide where to start.

Homes built on a concrete slab have drains running under the slab, so cracks there cannot be seen without a camera. Smells that come and go with the weather, or that sit around a floor waste after it has been refilled, can be a sign of a slab drain problem. Timber floored homes with a crawl space let the plumber look under the house for wet soil, broken pipes and loose joints. Both types of house benefit from a camera before anyone starts digging or cutting into a floor. Musty air under the floor can also come from poor airflow under the house, and underfloor ventilation installation addresses that problem.

Once the camera finds damage, the repair options are the same as for any broken drain. Digging up and replacing a short section is estimated at $1,500 to $4,500 for 2027. Pipe relining, where a liner soaked in resin is set hard inside the old pipe, costs about $200 to $350 per metre for a 100 millimetre sewer line. Repairs where the private drain meets the sewer branch, called junction repairs, are estimated at about $600 to $3,500. Before choosing, compare digging and relining in more depth through sewer line repairs.

Leaks from water pipes can also make a house smell damp and musty, which some people mistake for a sewer problem. Musty smells come from mould and wet timber, while sewer smells come from drain air and waste. Plumbers can tell the two apart by checking traps, drains and water pipes in the same visit. Treating mould without fixing the water source is unlikely to last, so the leak comes first. Old pipes that keep leaking in several places may need water pipe replacement rather than another patch. Should a hidden water leak turn out to be the cause, look at water leak detection or, for burst braided hoses under sinks, flexible hose replacement services.

The Overflow Relief Gully and Smells Outside

An overflow relief gully, or ORG, is a small outdoor drain with a loose grate, set near the house on the sewer line. Hunter Water describes it as a safety device that sends sewage out into the garden during a blockage, instead of up through the toilets and showers. Its grate is designed to pop off when sewage pushes up from below, so it must stay visible and uncovered. Building Commission NSW issued an advisory note in 2026 on gully heights, including a gap of at least 150 millimetres below the lowest fixture inside. The top of the gully's upright pipe should sit at least 75 millimetres above the finished ground or paving. Keep pot plants, mulch and garden edging off the grate so that it can lift freely.

A dry gully can smell like any other dry trap, especially in hot weather or when the house is empty. Topping it up with a hose for a few seconds refills the water seal and can stop the smell at once. If sewage is sitting in the gully or has spilled out, the drain is blocked and the next step depends on where the blockage is. In Sydney Water areas, call 13 20 90 if you think the problem is in Sydney Water's pipes, or a licensed plumber if it is in your own pipes. Clearing a blocked gully as an emergency is estimated at about $350 to $900 for 2027.

Gullies that sit too low, or that have been buried under paving or garden beds, let rain and soil wash into the sewer. Burying the gully in concrete or putting it under a home extension is something Hunter Water advises against. Raising or moving a gully is drainage work, and there is no published Quote Yard price range for it, so it is priced on quote. Where the right gully height cannot be achieved, the Building Commission note allows a reflux valve, a one-way valve that stops sewage flowing back, and the owner stays responsible for it.

Stormwater pits and grated drains can smell too, but they are a separate system from the sewer. Leaves, silt and still water left in a pit can rot and give off a swampy smell. Downpipes wrongly joined to the sewer are a different fault, and Sydney Water lists them among the problems its smoke tests find. Clearing leaves and silt from a pit by hand is a simple job for an owner, and a plumber can clear the pipe beyond it. For pits and stormwater pipes, get quotes for stormwater drainage plumbing instead of a sewer repair.

Drain or Appliance? Dishwashers, Washing Machines and Sinks

Kitchen and laundry smells are not always the drain, because appliances hold dirty water and food waste inside them. Smells that only appear when the dishwasher door opens or the washing machine runs suggest checking the appliance first. Smells from the sink plughole when nothing is running are more likely to come from the trap or the drain. Checking the appliance first can save the cost of a call-out for a problem the owner can fix. Food waste units under the sink can hold rotting scraps too, and a poor garbage disposal installation may leave a leaking joint below.

Electrolux makes dishwashers and lists dirty filters, food left in the sump, the well at the bottom of the machine, and dirty spray arms among the causes of dishwasher odour. Its advice is to scrape plates before loading, clean the filters and run a dishwasher cleaner each month. These are owner tasks that need no plumber, and the user manual shows how to remove each filter. Electrolux also says to check that the drainage pipe is not blocked and that the household plumbing is not affected. Plumbers can check where the dishwasher hose joins the sink waste, and a poor connection can be corrected during dishwasher installation work.

Front loading washing machines can hold damp lint and detergent in the door seal and drum. LG makes front and top loading washing machines and recommends running Tub Clean or a hot empty cycle each month. LG also advises wiping the rubber door seal after each wash, leaving the door slightly open and cleaning the drain pump filter every six months. AEG makes washing machines and says frequent washes at 40 degrees or less let residue, fluff and bacteria build up in the drum. Should the smell stay after these steps, the standpipe, the upright pipe the machine's hose drains into, or the laundry trap is the next place to check. Old laundry tubs with cracked wastes or missing traps are often best fixed through a new laundry sink installation.

Kitchen sink drains collect grease and food scraps, which rot in the trap and the pipe below. Slow drains with a sour smell need the trap cleaned or the branch line, the pipe that carries waste from the room to the main drain, cleared. Scraping plates into the bin before washing up keeps food scraps out of the sink trap. Sinks with a badly fitted waste or the wrong trap often smell again, so any kitchen sink installation should include a correctly sized trap. When a plunger fails, book blocked sink and basin repair services so a plumber can clear the trap and line. Heavy grease along the branch line may call for hydro jetting drain cleaning, which blasts grease off the full width of the pipe with high pressure water.

How a Plumber Tracks Down an Odour

Good odour visits start with questions about where, when and how strongly the smell appears. The plumber will want to know which rooms are affected, whether rain or the use of certain fixtures makes it worse and how long it has been going on. Notes and photos from the owner save time, because some smells come and go and may not be present on the day. The plumber then runs water through each fixture, checks traps and floor wastes, and listens for gurgling or slow draining.

Next, the plumber checks the parts of the system that are easy to see. That includes the seals around toilet pans, the joints under sinks, the vents on the roof and the outdoor gully. Handheld inspection cameras help to see inside wall cavities, cabinets and small pipes without cutting large holes. RIDGID makes the micro CA-350, a handheld inspection camera with a 17 millimetre camera head and a 90 millimetre colour screen. Its standard cable is 0.9 metres long and can be extended for deeper checks.

When the cause is still unclear, a drain camera on a longer cable goes into the sewer line through an inspection opening. Inspection openings are capped access points on the drain, with a screw cap or plug that the plumber removes. Iplex makes PVC inspection openings in the common 100 millimetre drain size, certified under WaterMark, the national approval scheme for plumbing products. The footage shows cracks, open joints, roots and sagging sections, and the plumber can mark the fault location on the ground. Marking the pipe's position and depth on the ground adds about $150 to $400 when a repair must be planned from the surface. Adding the camera to a clearing visit runs about $200 to $450, and you can also book drain camera inspection services on their own.

Plumbers can also test whether a drain holds water or air without leaking. Vinidex makes the IO Test Plug, a plug designed for pressure testing drain, waste and vent systems. The plumber seals the pipe at its openings, fills or pressurises it and watches whether the level or pressure drops. Any drop shows that the drain is leaking somewhere, even if the camera did not show an obvious crack. Failing the test narrows the search to one run of pipe, which keeps any digging or relining to the damaged part.

Smoke testing is another way to find leaks, and Sydney Water uses it in its Wastewater Fix program. Its team pumps a small amount of smoke into the private wastewater system through an inspection opening or a maintenance hole, the utility's access chamber on the sewer. Sydney Water describes the smoke as environmentally safe, and says it disappears after a few minutes without any odour. Smoke from roof vents is normal, but smoke inside the house is a sign of dry traps, cracked pipes, a damaged gully or a wrongly connected downpipe. There is no published Quote Yard price for a private smoke test, so ask the plumber to price it before the visit.

Who Pays: Private Pipes, the Sewer Main and Strata

Sewer smells can start on either side of the line where private pipes meet the public sewer. In Sydney Water areas, owners are responsible for all private wastewater pipes up to and including the point of connection, the place where the private pipe joins the main. That point can be outside the property, under a footpath or in a neighbour's yard. The main and the junction, the fitting where the private pipe joins it, belong to Sydney Water, and its faults line on 13 20 90 takes reports at any hour.

Other areas have their own water and sewer providers with similar rules. Hunter Water serves the Lower Hunter, and its 24 hour line is 1300 657 000 for sewer problems in its pipes. Hunter Water asks owners to check their sewer inspection shaft, a capped access pipe on the property, first, and to call it if the shaft is full or overflowing. Local councils run water and sewer services in many regional towns, so the council is the contact there. Essential Water serves Broken Hill, and homes without a sewer connection can book septic tank services for their on-site systems. Details for Sydney are on the Sydney Water website.

In strata buildings, the owners corporation, the legal body made up of all lot owners, looks after common property. Common property means the parts of the building that no single owner owns, such as shared walls, floors and roofs. The NSW Government's common property guide lists floor drains and sewers in common property, and pipes inside common walls or floors, as owners corporation items. Pipes that serve only one lot and sit outside common property, the trap under a sink and the toilet bowl itself, are listed as the lot owner's items. By-laws, the building's own rules, can change who pays, so check them before booking.

Sewer smells in apartments can travel between units through shared stacks, the large vertical drain and vent pipes. One unit's smell may come from a dry trap in an empty unit above or below. Tell the strata manager or building manager early, because access to other units may be needed. Owners of empty units can help by running water in each fixture whenever they visit. Shared drains and stacks are handled through strata and body corporate plumbing arranged by the building.

Licences, Notice of Work and the Certificate of Compliance

Plumbing and draining work in NSW needs a licence regardless of the job's cost. Draining includes the repair and cleaning of drains that connect to a sewer, so clearing or fixing a smelly drain is licensed work. Licences are issued under the Home Building Act 1989, and Building Commission NSW is the regulator, on 13 27 00. You can check a plumber's licence on the NSW Government's Verify licence register before work starts.

Most plumbing work also needs a Notice of Work, a form the plumber lodges to tell the regulator that the work is happening. Emergency work and minor work, such as replacing tapware, are exempt from the Notice of Work. At the end of all plumbing work, the plumber issues a Certificate of Compliance, which confirms the work meets the plumbing rules. A copy goes to the person who arranged the work, so keep it with your home records. Products used must be authorised, and the WaterMark scheme run by the Australian Building Codes Board certifies plumbing products. You do not lodge these forms yourself, because the licensed plumber is responsible for them.

Contracts matter for larger drain repairs that run into thousands of dollars. In NSW, residential building work over $5,000 including GST needs a written contract, and the deposit is capped at 10 percent. Statutory warranties, the warranties set by law, run for six years for major defects and two years for other defects. Ask for the contract to describe the fault found, the repair method and what happens to paths, gardens or floors. Contract rules and warranties are explained on the NSW Government website under home building.

Renters, Landlords and Urgent Smell Repairs

In a rental home, a sewer smell is a repair issue between the tenant and the landlord or agent. The NSW Government lists a gas leak, a blocked or broken toilet and a burst water service or serious leak as urgent repairs. Plain smells with working fixtures are not on that list, so they are handled as non-urgent repairs. Tenants should report the smell in writing, describe where and when it happens, and set a clear date for a response.

Where the smell comes with a blocked toilet or sewage spilling from a drain, the urgent repair rules apply. When the landlord or agent cannot be reached, a tenant can arrange the repair and be paid back up to $1,000. The landlord must repay within 14 days of written notice with the repair details and receipts. The work should be done by a licensed tradesperson, ideally one named in the lease, or the landlord may not have to repay. Tenants should not stop paying rent while waiting for a repair. Keep photos of the spill along with the invoice, because the landlord will need both to process the repayment.

When a non-urgent repair is ignored, the tenant can complain to NSW Fair Trading, which may order the landlord to fix it. If that does not work, the dispute can go to the NSW Civil and Administrative Tribunal, known as NCAT. Landlords can avoid disputes by booking a plumber soon after the first report and keeping the invoice and Certificate of Compliance. Tenants can also get free advice from a local Tenants Advice and Advocacy Service before a hearing. The same plumber visit can cover rental water efficiency compliance, which landlords need before charging tenants for water use. Routine checks between tenancies can be added to a plan for rental property maintenance.

Empty rental properties are prone to dry traps between tenancies. Running every tap, shower and floor waste during the final inspection and before new tenants arrive keeps the seals full. Agents can add this to the routine for vacant homes, along with flushing each toilet. Smells reported in the first week of a tenancy can come from a dry trap, not a fault, so try refilling first. Buyers looking at an empty home can ask for the same check during a pre-purchase plumbing inspection. Property managers can note the date of each refill in the inspection report.

Sewer Smell Repair Costs in NSW (2027 Estimates)

Smell jobs start with a call-out and diagnosis visit, before the plumber can quote for the repair. Using 2027 estimates, a call-out and diagnosis visit is about $90 to $160, and plumbers charge about $90 to $180 an hour in business hours. Some plumbers credit the call-out fee against the repair if you go ahead on the same day. After-hours work costs more, with hourly rates estimated at $150 to $250.

Job 2027 Estimate (NSW) What Drives the Price
Call-out and diagnosis visit $90-$160 Travel, time to test each fixture, whether the call-out is credited against the repair
Toilet pan seal or connector refit $200-$550 Toilet style, concealed or wall-hung pans, condition of the floor
Single fixture blockage cleared $150-$400 Fixture type, how far down the blockage sits, access to the trap
Laundry drain and trap replacement $200-$500 Pipe size, access behind the machine, parts needed
Camera added to a clearing visit $200-$450 Length of drain, access point, whether a report is needed
Camera inspection with written report $350-$800 Number of lines, report detail, locating and marking
Locating and depth marking of a drain $150-$400 Depth, ground cover, number of points marked
Overflow relief gully blockage cleared (emergency) $350-$900 Time of day, severity of blockage, cleanup needed
Drain section dug up and replaced $1,500-$4,500 Depth, paving or concrete, length of pipe, restoring the surface
Pipe relining, 100 mm sewer $200-$350 per metre Length lined, junctions, cleaning before lining
Vent repair, air admittance valve or trap primer Priced on quote Call-out fee, hourly rate, roof access and parts

The table shows that small fixes and large repairs sit far apart in price. Refilling a dry trap costs nothing, while digging up a cracked drain can run into thousands of dollars. That gap is the reason to find the cause properly before agreeing to a large repair. Spending a few hundred dollars on a camera can prevent a costly repair to the wrong section of pipe. Hourly rates and call-out fees for other jobs appear in the plumber pricing guide for NSW.

Several things push a smell repair toward the top of its price range. Smells that come and go can need two visits, because the plumber may need to see the problem while it is happening. Roof access, concealed toilets, tiled-in pipes and drains under slabs all add labour time. Regional travel, after-hours callouts and asbestos testing in older homes also add to the bill. Jobs with easy access, a clear cause and standard parts sit at the lower end of each range. Asking for a fixed price for the diagnosis visit removes some of this uncertainty.

What Moves the Price of a Smell Repair

Tracing a smell to one toilet seal or one dry floor waste means a short visit with a clear price. Wet-weather smells with no obvious fixture can take more time, a camera run and sometimes a second visit to confirm the cause.

Prices for vent repairs, air admittance valves, trap primers and private smoke tests have no published Quote Yard price range. Plumbers price these from the call-out fee, the hourly rate and the parts used, so ask for those three figures in writing.

All figures are 2027 estimates for NSW homes and exclude digging, concrete cutting, tiling and remote travel unless listed.

What to Look Out For in Sewer Smell Repairs

Be wary of any plumber who recommends a large repair without showing you the cause. For any quote that includes digging or relining, ask to see the camera footage that shows the crack, gap or root growth. Plumbers who have found the fault should be able to point to it on the screen and on the ground. Footage can also be shared with a second plumber if you want another opinion before paying for a major repair. Keep a copy, because it helps with later claims, sales and strata decisions.

Masking a smell is not the same as fixing it. Air fresheners, scented gels and drain deodorisers can hide sewer air while the gas keeps escaping. Strong drain chemicals carry safety warnings, so read the product label before using them. If a smell comes back within days of refilling a trap, there is a fault that needs a plumber.

Watch for signs that a smell has become a health or safety issue. Sewage spilling inside, wastewater rising in a shower or bath, and a blocked toilet in a home with only one toilet all need prompt action. A smell of gas instead of sewage always means leaving the building and calling 000 before anything else. Out of business hours, an emergency plumber costs more but can stop damage spreading. Keep children and pets away from any area where sewage has spilled until it is cleaned.

Check the plumber's licence and the paperwork they promise before work begins. A licensed plumber should give a written quote, a tax invoice and a Certificate of Compliance at the end. Be cautious of anyone who offers a cash price with no paperwork, or who says a licence is not needed for drains. Unlicensed drain work can leave you with no warranty, no compliance record and problems when you sell.

Getting Quotes That Fix the Cause

Good quotes for a smell problem start with good information from you. Tell the plumber which rooms smell, what time of day it happens and whether rain, wind or using a fixture makes it worse. Mention any recent renovations, new fixtures or work on the roof, because these can disturb vents and drains. Photos of the outdoor gully, roof vents and any damp patches help the plumber plan the visit. If you know the home's age and pipe types, include those details too.

Details to Include in a Quote Request

List each room where the smell appears and whether it is constant or comes and goes. Note whether any rooms or fixtures are rarely used, and whether refilling the traps changed anything.

Say whether the home is a house, a townhouse or a strata unit, and whether it is on a slab or has a crawl space. Mention any gas appliances nearby, so the plumber can rule out gas before starting.

Clear details help plumbers quote the diagnosis visit accurately and arrive with the right tools.

Compare quotes on what the plumber will check, not just the call-out price. One quote may cover traps and toilet seals only, while another includes a camera and a vent check. Ask what happens if the first visit does not find the cause, and whether a second visit is charged in full. Fixed prices for the diagnosis visit make it easier to compare plumbers side by side.

Once the cause is found, ask for a written quote for the repair itself. The quote should name the repair method, the parts, the time on site and any repairs to floors, walls or paving disturbed by the work. It should also say whether a Notice of Work will be lodged and when the Certificate of Compliance will be issued. Clear written scopes also make it easier to check the final invoice against what was agreed. Other repairs found on the day can be quoted alongside it, from the full range of plumbing services in NSW. Owners in the city can also hire a plumber in Sydney and compare local quotes for the repair.

After the repair, test the result over the following weeks. Run water into rarely used fixtures, check that the smell has not returned after rain, and look at the outdoor gully. Should the smell come back, contact the plumber who did the work and ask whether a repeat visit is covered. Keep the invoice, footage and Certificate of Compliance together for future owners, tenants or strata records. Workplace hazards on plumbing jobs, such as roof access and asbestos, are regulated by SafeWork NSW.

Odour Repair Plumbers in Every NSW Region

We connect homeowners, tenants, landlords and strata managers with licensed plumbers throughout New South Wales for smell inspections, toilet seal repairs and drain checks. Post your job once and compare quotes from plumbers who work in your area.

▶ Sydney Inner City 18 areas
Sydney CBD Surry Hills Darlinghurst Potts Point Paddington Redfern Newtown Glebe Balmain Pyrmont Ultimo Chippendale Alexandria Waterloo Zetland Erskineville Rozelle Leichhardt
▶ Greater Sydney 25 areas

Western Sydney

Parramatta Penrith Blacktown Mount Druitt Seven Hills Wetherill Park Auburn Fairfield Cabramatta St Marys

South Western Sydney

Liverpool Campbelltown Bankstown Revesby

Northern Sydney

Hornsby Chatswood Epping Macquarie Park Eastwood

The Hills District

Castle Hill Baulkham Hills

Inner West

Ryde Strathfield Burwood

St George

Hurstville Kogarah
▶ Sydney Coastal 23 areas

Northern Beaches

Manly Dee Why Curl Curl Freshwater Brookvale Collaroy Narrabeen Mona Vale Newport Avalon Palm Beach

Eastern Suburbs

Bondi Tamarama Bronte Coogee Maroubra Randwick

Harbour Suburbs

Double Bay Rose Bay Watsons Bay

Sutherland Shire

Cronulla Miranda Sutherland
▶ Hunter & Central Coast 19 areas

Central Coast

Gosford Terrigal Wyong The Entrance Tuggerah Erina Woy Woy

Hunter Valley

Newcastle Maitland Lake Macquarie Charlestown Belmont Raymond Terrace Cessnock Singleton Muswellbrook

Port Stephens

Nelson Bay Salamander Bay Shoal Bay
▶ Illawarra & South Coast 18 areas

Illawarra

Wollongong Shellharbour Kiama Dapto Corrimal Thirroul Gerringong

Shoalhaven

Nowra Berry Ulladulla Huskisson Vincentia

Sapphire Coast

Batemans Bay Moruya Narooma Bega Merimbula Eden
▶ North Coast 19 areas

Mid North Coast

Port Macquarie Forster Taree Kempsey Laurieton

Coffs Coast

Coffs Harbour Bellingen Sawtell Grafton Yamba

Northern Rivers

Byron Bay Tweed Heads Ballina Lismore Bangalow Lennox Head Brunswick Heads Mullumbimby
▶ Blue Mountains & Highlands 17 areas

Blue Mountains

Katoomba Leura Wentworth Falls Blackheath Springwood Hazelbrook Glenbrook Faulconbridge Lawson Blaxland Lithgow

Southern Highlands

Bowral Moss Vale Mittagong Bundanoon Robertson Berrima
▶ Regional NSW 21 areas

Central West

Orange Bathurst Dubbo Mudgee Parkes Forbes Cowra Young

Riverina

Wagga Wagga Albury Griffith Leeton Goulburn Queanbeyan

New England

Tamworth Armidale Inverell Moree Narrabri

Far West

Broken Hill Cobar

Sewer Smell and Drain Odour FAQs

Why does my bathroom smell like sewage only some of the time?
Odours that come and go can follow a pattern, such as appearing after a toilet flush, after a bath drains or after heavy rain. Heavy rain can make sewer smells rise through floor drains, according to Hunter Water, and a dry trap smells again once its water evaporates. Gurgling or a smell after flushing can be a sign of a vent problem that pulls water out of nearby traps. Keep a note of the times and conditions, because this helps a plumber find the cause in fewer visits. Refill each trap first, and book a plumber if the smell keeps returning.
Is a rotten egg smell from gas or from the sewer?
Both can smell like rotten eggs, so you cannot safely tell them apart by smell alone. According to the NSW Government, the warning chemical added to gas makes it smell a bit like rotten eggs. If the smell is near a gas appliance, gas meter or gas bottle, leave the building, call 000 and then ring the gas supplier on your bill. Only once gas has been ruled out should you treat it as a drain smell and call a plumber.
Can I fix a dry trap myself?
Yes, refilling a dry trap is simple and needs no licence or tools. Run the tap, shower or bath for a few seconds, flush the toilet, or pour a bucket of water into each floor waste. If the smell goes away and stays away, the trap had simply dried out from lack of use. If the smell returns within a day or two, the trap may be leaking, cracked or losing water through a vent fault. Replacing a trap or waste pipe is licensed plumbing work in NSW, so call a plumber at that point.
Who pays when the smell comes from the sewer main?
In Sydney Water areas, the owner pays for private pipes up to and including the point of connection with the main. Sydney Water owns the main and the junction, and you can report suspected faults in its pipes on 13 20 90. Hunter Water and regional councils have their own rules, so check with your provider before arranging work on their side. Camera footage from a plumber helps show which side of the connection the fault sits on.
My strata unit smells of sewage. Is it my problem or the owners corporation's?
It depends on where the fault is and what your by-laws say. The NSW common property guide lists floor drains and sewers in common property, and pipes inside common walls and floors, as owners corporation items. Pipes that serve only your lot and sit outside common property, the trap under your sink and your toilet bowl are listed as yours. Report the smell to the strata manager early, because shared stacks can carry smells between units. Dry traps in empty units nearby can also be the cause.
Will air fresheners or drain deodorisers fix a sewer smell?
They can hide the smell for a while, but they do not stop sewer air leaking into the house. If a trap is dry, a toilet seal has failed or a drain is cracked, the gas keeps escaping behind the scent. Strong drain chemicals carry safety warnings, so follow the product label if you use them. Refill traps, check the obvious fixtures and call a plumber if the smell does not clear.
Does my landlord have to fix a sewer smell?
Landlords must keep a rental home in reasonable repair, and plumbing faults are part of that duty. Urgent repairs listed by the NSW Government include a blocked or broken toilet and a gas leak, while a plain smell is handled as a non-urgent repair. Report the smell in writing with dates and details, and give the landlord a clear deadline to act. If nothing happens, you can complain to NSW Fair Trading and then apply to NCAT if needed.
Smoke came out of my roof vent during Sydney Water testing. Is that a problem?
No, Sydney Water says smoke from private wastewater vent pipes is normal and shows the vents are working. Its smoke is described as environmentally safe, and it disappears after a few minutes without an odour. Smoke inside the house is different, because it is a sign of a dry trap, a cracked pipe or another fault. Sydney Water asks residents to put water in sinks and cover floor drains during its tests. Tell the testing team if smoke appears indoors, and book a plumber to check the fault.
What should I tell the plumber when I book a smell inspection?
Describe which rooms smell, how strong the smell is and when it appears or gets worse. Mention whether any bathrooms, laundries or floor wastes are rarely used, and whether refilling them helped. Say whether the home is on a slab or has a crawl space, and whether there are gas appliances nearby. Photos of the outdoor gully, roof vents and any damp areas help the plumber prepare for the visit. Ask for the call-out fee, hourly rate and any camera charge in writing.
Do I get paperwork after a sewer smell repair?
Yes, a licensed plumber in NSW must issue a Certificate of Compliance at the end of plumbing work. The person who arranged the work receives a copy, and it confirms the work meets the plumbing rules. Larger jobs, such as drain replacement, also need a Notice of Work lodged with the regulator before work starts. Keep the certificate with your invoice and any camera footage for future sales, claims or strata records.

Other Trades for Smells, Damp and Ventilation

For Trades & Contractors - NSW

Plumbers who enjoy tracking down smells and drain faults can find new work on the NSW job leads board, along with plumber jobs in NSW and emergency plumber jobs.

Ready to Get Rid of That Smell?

Post your job and compare quotes from licensed NSW plumbers for odour inspections, seal repairs and drain checks.

Get Free Plumber Quotes

About This Guide

This guide is general information only, and NSW rules, utility policies, product details and prices can change. If you smell gas, leave the building and call 000 first. Confirm sewer requirements with your water and sewer provider, Building Commission NSW, your owners corporation where relevant, and a licensed plumber before work starts.

Reviewed by The Quote Yard Editorial Team

Published 18 November 2026 ·

How The Quote Yard Works

We connect you with independent local tradies and service providers, we don't perform any trade work ourselves. Tradies provide their own quotes directly to you. Always confirm licensing, insurance, and scope of work before engaging any provider.

All NSW tradies are required to hold appropriate licences. Verify at NSW Fair Trading.
Prices are 2027 estimates for New South Wales and exclude digging, relining, roof access and remote travel unless listed. Vent repairs, air admittance valves, trap primers and private smoke tests are quoted per job.
Need work done? Get free quotes. Post a Job – It's Free