Slow or Repeatedly Blocked Drains?
Tell us which drains are slow, whether anything has overflowed and how old the home is, and we'll connect you with licensed plumbers near you.
Typical Costs (2027 Estimates)
These figures are 2027 estimates for NSW homes. Stormwater pit cleaning, repairs found on camera and regional travel are priced per job.
Hydro Jetting Drain Cleaning Services NSW - Get Local Quotes
Hydro jetting cleans drains with water pumped at high pressure through a flexible hose and a shaped nozzle, fed into the pipe from an outdoor access point. The nozzle scours the inside of the pipe, washing grease, silt, sand, soap scum and fine roots down the line toward the sewer or the street drain. A licensed plumber uses it on household sewer lines, kitchen sink drains and stormwater pipes when a plunger or drain cable only opens a small hole through the blockage. Jetting suits sound pipes, but old clay joints, cracked sections and asbestos cement pipes need a camera check before any water goes in. Using 2027 estimates for NSW, jetting one drain line costs about $250 to $900, and cutting out roots and then jetting the line about $400 to $1,200. Adding a camera to the same visit costs about $200 to $450, and the footage shows what the pipe is made of and whether a repair is needed. Roots growing through a cracked joint come back after jetting until the pipe itself is fixed. Price depends on access, the length of pipe, how packed the blockage is, the pipe material and whether the work happens after hours. Owners pay for their private pipes up to where they connect to the public sewer, while Sydney Water, Hunter Water or the local council looks after the main. In NSW, cleaning a sewer drain counts as draining work, so it needs a licensed plumber whose licence covers draining. Home pressure washer drain kits do not change that rule for sewer drains.
At a Glance - Hydro Jetting and Drain Cleaning in NSW (2027 Estimates)
| Job | 2027 Estimate (NSW) | Best For | Access Needed | What You Receive |
|---|---|---|---|---|
| Jetting one drain line | $250-$900 | Grease, silt, soap and fine roots in a sound pipe | Inspection opening (capped access pipe) or outdoor gully | Tax invoice |
| Roots cut and line jetted | $400-$1,200 | Root mats at cracked joints | Opening near the root entry | Invoice and root location |
| Camera added to a clearing visit | $200-$450 | Checking the pipe before or after jetting | Same access point as the jetting hose | Footage and short summary |
| Main line jetted and filmed (Sydney) | $600-$1,300 | Repeat blockages on the main sewer line | Boundary trap (sewer fitting near the front fence) or opening | Footage and written findings |
| Standalone drain camera inspection | $300-$750 | Planning a repair or buying a home | Any opening on the line | Video and report |
| Camera (CCTV) stormwater inspection | $300-$800 | Pits that overflow in rain | Stormwater pit | Video and report |
| Emergency blocked drain (after hours) | $400-$900+ | Sewage coming up inside or outside | Nearest working access | Tax invoice |
| New access pit added | $1,500-$4,000 | Lines with no way in | Digging down to the pipe | Certificate of Compliance |
Cost Depth: What Moves a Jetting Price
A short kitchen drain reached through an inspection opening, a capped access pipe on the drain, costs the least to jet. A long sewer line packed with roots, with no easy way in, costs the most, because the plumber cuts, jets and films in one visit.
When the work happens also changes the bill. An after-hours blocked drain is estimated at $400 to $900 or more, while the same clean booked on a weekday can fall within $250 to $900 for one line.
All figures here are 2027 estimates for NSW homes. Repairs found on camera, new access points and remote travel are quoted separately.
What Hydro Jetting Does Inside a Drain
Hydro jetting, also called high-pressure water jetting, cleans the inside of a drain with water forced through a small nozzle. The plumber feeds a reinforced hose into the pipe from an access point, and a petrol or electric pump at the surface, called the jetter, supplies the water. Jets on the nozzle point backwards and sideways, so the water drives the hose along the pipe while it washes the walls. As the hose is drawn back, the loosened material is flushed down the line toward the sewer main or the street drain. The result is a pipe washed across its full width, not just pierced through the middle of the blockage.
Household drains carry two kinds of water, and jetting is used on both. Sanitary drains take wastewater from toilets, showers, sinks and the laundry to the sewer, or to a septic tank on blocks with no sewer connection. Stormwater drains take rain from the roof, paved areas and yard pits to the street gutter, a council pipe or an absorption pit that lets water soak into the ground. Sydney Water treats downpipes joined to private wastewater pipes as wrongly connected, so the plumber should confirm which system is blocked before starting.
Jetting is one of several clearing methods, and plumbers often try a simpler one first. Blocked toilets and basins can clear with a plunger or a short hand auger, and those jobs have their own guides. For trouble at a single fixture, start with our pages on blocked toilet repairs and blocked sink and basin repairs. Jetting comes in when a blockage sits further down the line, keeps returning, or is made of material that a drain cable cannot shift. Plumbers also jet a pipe before filming it or lining it with a new inner pipe, since the camera needs a clear view of the walls. Knowing why the plumber has chosen it helps you judge whether the price on the quote makes sense.
Signs a Drain Needs More Than a Plunger
The signs of a wastewater blockage listed by Sydney Water include sinks, baths or toilets that empty slowly and toilets that do not flush properly. Gurgling from a toilet or floor drain is on the same list, as is wastewater spilling from the gully, the small grated outdoor drain often near a tap. When two or more fixtures are slow at once, the blockage is probably further down the shared line, beyond the reach of a plunger. Water rising in the shower when the washing machine empties is another clue that the shared drain is restricted. These patterns call for a machine that can clean a length of pipe, not a tool that only reaches the bend under one fixture. Note which fixtures are affected and the order they slowed in, since that helps the plumber choose the right access point.
Act quickly once sewage appears outside the house. Wastewater spilling from the gully suggests the private line is blocked and sewage is reaching the garden or paving. Stop using water inside, keep people and pets away from the spill and call a licensed plumber. If a public manhole or a neighbour's yard is overflowing as well, the fault may be in the public sewer main, which the water authority clears. Wear gloves for any clean-up, and keep children away until the area has been washed down.
Jetting Compared With an Electric Eel or Hand Auger
An electric eel is a motor-driven steel cable with a cutting head on the end that spins its way through a blockage. It suits solid obstructions such as a wad of wipes, a toy or a root mass, because the head grabs or cuts the material. The cable only clears a path about as wide as its head, so grease and silt stuck to the pipe walls can stay behind. Jetting washes those walls, but water alone can struggle against a tight, woody root ball. For that reason, plumbers sometimes cut roots with a cable first and then jet the line to wash the pieces away.
Plungers and hand augers, short hand-cranked cables, work best close to the fixture, inside sink bends, toilet bowls and short waste pipes. They cost less to use because the visit is shorter and no large machine has to be set up outside. Jetting equipment takes longer to set up, needs a water supply and has to be run from a suitable access point. That set-up time is one reason a jetting visit costs more than a plunger visit, even when both clear the same drain.
Neither method is better in every case, so find out why one has been chosen for your drain. Good answers name what is likely in the pipe, such as grease from the kitchen, sand from a cracked joint or fine roots. Where the plumber cannot say, a camera look after the first attempt can show what is there before more money is spent. The wider range of clearing methods, and the faults behind them, are compared in our blocked drains guide for NSW. Jetting has its own limits, and a careful plumber explains them before starting.
Nozzles, Hoses and the Size of the Machine
The choice of nozzle shapes much of what a jetter can do in a given pipe. Nozzles with jets facing mainly backwards pull the hose along and scrub the pipe wall, which suits grease and silt. Some nozzles add a forward jet to open a path through a packed blockage before the rear jets wash it out. Rotating and pulsating nozzles spin or pulse the water to break up roots and hardened deposits. Aussie Pumps makes the Aussie Root Mulcher, one of its specialty nozzles, a turbo pulsating design for cutting through tree roots and other debris.
Both pressure and flow matter, and a high pressure figure on its own does not promise a better clean. Pressure is the force behind the water, measured in pounds per square inch (psi) or in bar, a metric unit equal to about 14.5 psi, while flow is the volume of water moving each minute. Flow carries the loosened material away, so a jetter with too little water can stir up a blockage without flushing it down the line. RIDGID makes the KJ-3100 water jetter, rated at 3,000 psi for drain lines from 50 to 250 millimetres across. Aussie Pumps makes the Aussie Cobra drain cleaning jetters in Australia, in 4,000 and 5,000 psi versions with flows up to 30 litres a minute. Safe Work Australia's guide to managing jetting risks puts drain cleaning machines at around 150 to 210 bar, about 2,200 to 3,000 psi, with high power at the nozzle.
Machine size also depends on how the plumber reaches your property. Trolley units can be wheeled down a narrow side path, and Aussie Pumps says its Cobra frames fit through a standard doorway. Larger trailer and truck units carry longer hoses for long commercial pipes and big strata buildings. Mention tight access when you book, especially for a terrace, a steep block or a rear lane.
Hose length matters too, since it sets how far the jet can travel from one access point. Aussie Pumps fits its Cobra units with a steel reel holding up to 60 metres of sewer cleaning hose. Long runs from a single access point need enough hose to reach the blockage and wash past it. Where the line is longer than the hose, the plumber may need a second access point further along. Safe Work Australia's guide also warns against heavy, repeated use of the same hose when cleaning long drain lines.
Hydro Jetting Prices for 2027
Jetting is quoted per job or per hour, and the bands below come from Quote Yard NSW plumbing pages. Every figure is a 2027 estimate, and the final price can change once the plumber sees the access and the blockage. A business-hours call-out fee is estimated at $80 to $150, and hourly labour at $90 to $180. Jetting one household drain line costs about $250 to $900, depending on its length and what is in it. Our NSW pricing pages note that plumbers commonly charge at least one hour of labour, so a quick visit may still be billed as an hour.
| Job | 2027 Estimate (NSW) | What Drives the Price |
|---|---|---|
| Call-out fee, business hours | $80 to $150 | Distance and minimum attendance time |
| Hourly labour, business hours | $90 to $180 per hour | Time on site, set-up and clean-up |
| High-pressure jetting of one drain line | $250 to $900 | Length of pipe, access point and blockage type |
| Roots cut and line jetted | $400 to $1,200 | Size of the root mass and number of entry points |
| Camera added to a clearing visit | $200 to $450 | Footage only or footage with a written report |
| Main line jetted and filmed, Sydney | $600 to $1,300 | Pipe length, depth and report detail |
| Standalone drain camera inspection | $300 to $750 | Number of lines, locating and reporting |
| CCTV (camera) stormwater drain inspection | $300 to $800 | Number of pits and lines filmed |
| Emergency blocked drain, after hours | $400 to $900 or more | Night, weekend or public holiday timing |
| Remote regional travel charge | $150 to $400 | Distance beyond a regional centre |
| Stormwater pit or line jetting | Priced on quote | Number of pits, silt volume and disposal |
The wide jetting band reflects differences between our pages and between parts of the state. In Sydney regions, hydro-jet clearing costs about $250 to $600 as a 2027 estimate, according to our blocked drains guide. In regional NSW, the 2027 estimate for the same work is $210 to $520, depending on the town and its distance from the plumber. Remote properties can attract a travel charge, estimated at $150 to $400, where the plumber drives well beyond a regional centre. Within any one area, a short line reached through a gully costs less than a long line with no access point. Ask for the quote in writing so you know which part of the band your job falls in.
Read each quote for what sits inside the price. Some plumbers include the camera, clean-up of the work area and removal of debris collected at pits, while others charge for them separately. Goods and services tax should be shown on the quote, and the invoice should list each item. Parts such as a replacement grate or inspection cap are small costs but should still appear as their own lines. Our NSW pricing pages estimate that plumbers add 10 to 30 percent to what they pay for parts.
Adding the relevant bands gives a rough guide before you ask for quotes. Suppose a plumber attends a slow sewer line in business hours, cuts roots at a cracked joint, jets the line and films it. Cutting roots and jetting is estimated at $400 to $1,200, and a camera added to the same visit at $200 to $450. For comparison, jetting and filming a Sydney main line, the main private sewer pipe to the street, is estimated at $600 to $1,300 on our blocked drain plumber cost page. Add $80 to $150 if the plumber charges a separate call-out fee. For call-out, weekend and public holiday rates across the state, see our NSW plumber pricing guide.
After-hours work costs more, and an emergency blocked drain outside business hours is estimated at $400 to $900 or more. Labour outside business hours runs about $150 to $250 an hour, compared with $90 to $180 in business hours. Drains that are slow but still flowing can wait for a weekday booking, which keeps the bill lower. Sewage coming up through a gully, a shower or a toilet is different, because it is a health risk and can damage floors. When sewage is coming into the house at night, an emergency plumber in NSW can attend.
Blockages That Jetting Clears Well
Kitchen grease is the clearest case for jetting, because fat cools and sets on the pipe wall in layers. Cables can bore through the middle, but the layer left on the walls keeps catching food and fat afterwards. Jetting the kitchen branch line, the pipe from the sink to the main drain, washes that layer away along its length. Sydney Water asks households to wipe grease off dishes with paper towel and pour fats and oils into a container for the bin. When a kitchen is being refitted, kitchen sink installation is a good moment to have the branch line checked as well. Anyone planning a garbage disposal installation should also ask whether that branch line is clean enough to carry ground food scraps.
Sand, soil and silt enter drains through cracked joints, broken pits and yard gullies left uncovered during building work. They settle in low spots and bends, where they build up into a firm bed that slows the flow. Water from a jetter lifts the sediment and carries it downstream, which a cutting cable cannot do. If sand keeps returning after jetting, the pipe may have a crack or open joint letting soil in, and a camera can find it.
Soap scum and hair from showers and lint from washing machines also line the walls of branch lines. These build slowly and are easy to miss until water backs up in a floor waste, the drain set into a bathroom or laundry floor, or in a laundry sink. RIDGID lists sludge, soap, grease and sediment among the materials its KJ-3100 jetter is built to clear. In stormwater lines, leaves, roof grit and silt washed off paved areas build up in the same way. Jetting clears all of these, provided the pipe around them is still in sound condition.
Some blockages are a poor match for water alone. Toys, phones and wads of wipes caught at a bend are better hooked or cut out with a cable, since a jet can push them further down. Concrete slurry or tile grout washed down a drain during renovation can set hard inside the pipe. Removing it needs a cutting head or a repair, not a wash. Sagging sections, where water sits in a dip along the line, collect waste again after any clean, because the shape of the pipe is the cause.
Tree Roots, Root Cutting and Regrowth
Roots grow into sewer pipes through cracks and loose joints, where water and nutrients are available. Before planting, Sydney Water advises checking the sewer service diagram, a plan of the private sewer pipes, and keeping new trees more than 6 metres from wastewater pipes. Once inside, fine roots form a mat that traps paper and solids, and thick roots can fill the pipe. Fine root mats can be washed out with a jetter fitted with a rotating or pulsating nozzle. Woody roots are cut first with a cable machine or a cutting nozzle, and the line is jetted afterwards to clear the cut pieces.
Cutting and jetting removes the roots inside the pipe, but the crack that let them in remains. Roots can grow back through the same opening, so a clear drain after one visit does not mean the fault is fixed. Filming after the clean shows whether the entry point is a single joint or a run of damaged pipe. Repairs such as lining the pipe or replacing a section are compared on our pipe relining and drain repairs page. Some owners book jetting at set intervals to keep roots under control while they save for a repair. That approach works only while the pipe around the roots stays intact, which the camera can confirm.
Removing the tree is a separate decision, and your local council can tell you whether its tree rules apply before anything is cut. Arborists can advise on the tree itself, and a stump grinding and tree root removal contractor can deal with roots near the line once the plumber has marked it. Chemical root treatments are also sold to slow regrowth, and our sewer pages give a 2027 estimate of $100 to $250 per application. Check with the plumber whether a treatment suits your pipe material and the garden beds around it. No treatment seals the crack, so it is a holding measure while you plan a repair.
When Jetting Can Damage an Old or Broken Pipe
Water at high pressure is strong enough to harm a pipe that is already weak. Older NSW homes can have sewer lines of glazed clay, also called earthenware, joined with mortar or rubber rings. Over decades those joints can crack or shift with roots and ground movement, leaving sharp edges and gaps. Water aimed at a loose fragment can push it further out of place, and some can escape into the soil through an open joint. Our blocked drain cost guide also lists collapsed sections and old fibre cement drainage among the pipes that high pressure water can damage.
SafeWork NSW lists cement pipes, sewer vent pipes and in-ground pipes among the plumbing items that may contain asbestos in homes built before the late 1980s. The regulator also rules out high-pressure water spray, jets and similar tools on asbestos, and its guidance is on the SafeWork NSW website. Damaging the surface of an asbestos cement pipe can release fibres into the air. If your home is older and the drain material is unknown, the plumber should identify the pipe on camera before any jetting starts. Where a sample is needed to confirm the material, an asbestos testing and inspection service can arrange it. SafeWork NSW recommends a licensed asbestos professional to assess or remove any amount of asbestos, so ask how a damaged section would be handled.
Pipes that have collapsed or lost their shape need a repair, not a clean. Jetting into a collapsed section can wash more soil into the line and make the blockage worse. Warning signs include blockages at the same distance each time, sinking ground over the line and stones coming out at an inspection point. Our sewer line repairs guide shows how a damaged section is found, dug up or lined.
Camera Checks Before and After the Jet
A drain camera is a small waterproof camera on a flexible push cable that records video as it travels along the pipe. Filming before jetting shows what the pipe is made of, where it is damaged and whether jetting is safe. A second pass afterwards shows whether the walls are clean, how much root growth was present and where the entry points are. Clean walls give a clearer picture than a pipe still coated in grease, so on sound lines some plumbers jet first and film second. For more on footage, written reports and pipe locating, read our guide to drain camera inspection in NSW.
Plumbing cameras range from small handheld units for short branch lines to reel systems that travel the length of a sewer run. Some camera heads carry a locating transmitter, also called a sonde, which sends a signal so the plumber can mark the head's position on the ground. That mark shows where to dig or where a lining job should start if a repair is needed. Ask whether the camera can locate, since footage without a position shows a fault but not where it sits under the yard.
Request the footage and a short written summary whenever a camera is used. Useful summaries list the pipe material, the length filmed, the defects found and their distance from the access point. Store them with your home records, since they help the next plumber and can matter when you sell. Buyers can have the drains filmed before exchange of contracts as part of a pre-purchase plumbing inspection. As 2027 estimates, camera work costs $200 to $450 when added to a clearing visit and $300 to $750 as a standalone inspection.
How the Plumber Gets Into the Drain
A jetter needs a way into the pipe, and where that access point sits affects the time and the price. Inspection openings are capped fittings on the drain that let a plumber put a hose or camera straight into the line. Iplex makes DN100 PVC plastic inspection openings, meaning a nominal 100 millimetre pipe size, certified under WaterMark, the national approval scheme for plumbing products. Older homes may have a boundary trap, a water-filled bend near the front fence that holds back sewer gas, or an upright inspection shaft. Hunter Water says owners in its area are responsible for maintaining both. Without a suitable opening, the plumber may have to lift a toilet pan off the floor or work down from the vent pipe on the roof, which adds labour.
The overflow relief gully is a small outdoor drain with a loose grate, placed so sewage spills outside during a blockage instead of inside. Sydney Water's guidance says it acts as a safety outlet for sewage and must keep stormwater out of private wastewater pipes. Hunter Water advises keeping the gully uncovered, so never bury it under paving, soil or a pot plant. Holman makes 100 millimetre flat and domed PVC grates for indoor and outdoor drainage, and a plumber can fit a new one if yours is cracked. Hunter Water says a gully usually sits about 75 millimetres above the ground and at least 150 millimetres below the lowest inside drain, such as a shower drain. A sewer smell around the gully or inside the house is a separate fault, often a dry trap or broken seal, and calls for sewer smell and drain odour repair rather than jetting.
Where no access point exists, the plumber may recommend adding one during the visit or at a later repair. Our relining page gives a 2027 estimate of $1,500 to $4,000 for adding a new access pit, since it involves digging down to the pipe. On a line that needs regular cleaning, a new opening can shorten every later visit. Have the location marked on a sketch, and keep the sketch with your sewer service diagram.
Sewer Lines and Stormwater Lines Need Different Handling
Sewer lines carry wastewater to the public main, so anything washed down them ends up in the sewer system. Stormwater lines carry rain to the street or a council drain, and what goes down them can reach creeks and harbours. That difference affects what the plumber flushes downstream and where silt and debris are collected. On a stormwater line, the plumber may scoop sludge out of a pit instead of washing it into the street system. Jetting a sewer line is draining work under NSW licensing, so the plumber must hold the right licence for it.
Owners look after both sets of pipes on their land. Sydney Water says property owners have a role in maintaining the wastewater and stormwater pipes and connections on their property. It also lists stormwater downpipes wrongly connected to private wastewater pipes as one way rain gets into the sewer. Where the camera finds a downpipe running into the sewer, get a quote to correct it, since jetting will not fix the cause.
Stormwater lines block with leaves, roof grit, silt from paved areas and roots, and they can fill quickly during heavy rain. Water pooling at a pit or spilling from a downpipe joint during rain suggests a blockage further down the line. Filming through the pit can show whether the line is full of silt, crushed or invaded by roots. New stormwater pits are priced on our stormwater drainage plumbing page, along with a CCTV (closed-circuit television) stormwater inspection at $300 to $800 for 2027. Reln makes the Storm Drain slimline pit, which sits at the end of a channel drain, a grated trench set into paving, and connects to 90 millimetre PVC stormwater pipe. Vinidex makes PVC stormwater pipes to AS/NZS 1254, the Australian and New Zealand standard that sets their stiffness classes.
Keeping Roof Debris Out of the Stormwater Line
Leaves and grit from the roof are a steady source of stormwater blockages, especially where trees overhang the house. Rain Harvesting makes Leaf Eater rain heads, fitted beneath the gutter at the top of a downpipe to keep leaves and debris out. Screened rain heads stop material at a point you can reach and clean, before it enters the buried line. Stratco makes gutter guard mesh that keeps leaves and debris out of the gutter, and with regular gutter cleaning it reduces the load reaching the downpipes and pits. Cracked or leaking downpipes can be fixed by downpipe repair and replacement contractors, and the line below can then be jetted clean.
Yard pits need the same attention, since silt collects in the base and flows on into the pipe once the pit fills. Lift the grate after heavy rain and scoop out leaves and sediment by hand while wearing gloves. Stormtech makes linear and slot drains, narrow grated channels, for outdoor and landscaped areas, and the same scoop-out routine suits those channels. Avoid hosing the silt down the outlet, because it settles further along where it is harder to reach. If the pit drains slowly even when empty, the pipe beyond it needs attention from a plumber.
What Happens During a Jetting Visit
The plumber begins by asking which fixtures are slow and whether sewage has come up anywhere inside or outside. Next comes finding an access point and, where needed, running the camera to check the pipe material and condition. The jetter is set up outside, connected to a water supply and fed into the line with the chosen nozzle. Dirty water moves through the line during the clean, so keep children and pets away from open gullies and pits. Once the line runs freely, the plumber should test it by running fixtures and watching the flow at the access point. Some plumbers then run the camera again to confirm the walls are clean and to record any defects.
Expect some noise from the pump and some splashing around the access point. Before work starts, agree on who cleans the work area, replaces caps and grates and removes waste collected from pits. Inside the house, hold off flushing toilets and running taps until the plumber says the line is clear. On a rural block with only tank water, the plumber may need to bring water or confirm that your tank can supply the jetter.
Safe Work Australia's jetting guide lists the water jet piercing the skin and flying debris among the common hazards of the work. Jets can injure anyone who handles the hose end or stands over an open pipe, so stay clear while the machine runs. Those hazards are managed with training, protective gear and machine controls, which is part of what you pay for. Do not try to help by holding the hose, lifting grates or reaching into the line. If water comes up inside the house during the clean, tell the plumber straight away so the pump can be stopped.
Pressure Washer Drain Kits and the Licence Rules
Drain cleaning hoses are sold as accessories for home pressure washers, and they look like a small version of a plumber's jetter. Kärcher makes a 15 metre pipe cleaning set for its K2 to K7 home pressure washers, sold for clearing blockages in pipes, drains, downpipes and toilets. Gerni makes a 15 metre drain and tube cleaner that it describes for clearing debris from blocked pipes, drains and house guttering. STIHL makes a 15 metre pipe cleaning set for narrow pipes on its RE 90 to RE 170 PLUS pressure washers, giving a downpipe as an example. These descriptions are written for buyers across Australia and say nothing about NSW licensing. A use printed on the packet does not make that use lawful for a householder on a sewer drain.
NSW applies a plain licence rule to sewer drains. The NSW Government defines draining work to include flushing or cleansing of any sanitary drain connected to a sewer, and nsw.gov.au says it needs a licence whatever the cost. According to Sydney Water, confident householders can change a tap washer, while bigger plumbing problems need a licensed plumber. A householder should therefore never run a pressure washer kit, or any other jetting hose, down a sewer drain, toilet or floor waste.
Leaving sewer jetting to a licensed plumber also protects the house. Home kits give no view of the pipe, so one could be used on asbestos cement or a broken clay joint without anyone knowing. Water forced into a broken sewer can leak into the ground under the house. Blockages that push back can send dirty water out of the nearest gully or floor waste. Once a plunger at the fixture has failed, call a licensed plumber whose licence covers draining.
After the Drain Is Clear: Repairs and Maintenance Jetting
When the camera shows damage, clearing the drain gives you time to choose a repair. Options include lining the pipe from the inside, replacing a damaged section, or regular jetting while you save for the repair. As 2027 estimates, lining a 100 millimetre sewer costs $200 to $350 a metre, and relining a single junction, where two pipes join, at $600 to $1,500. Digging up and patching a small section costs about $1,500 to $4,500, while replacing a home's full sewer line can cost $4,000 to $15,000. Get each option in writing so you can compare a repair with several years of maintenance visits.
Planned maintenance jetting suits a known problem line, such as a kitchen branch that collects grease or a sewer with one root entry point. Our pages have no published price for a maintenance plan, so get a written price per visit and an agreed interval. Base the interval on what the camera shows, not on a fixed calendar offered to every customer. If the line blocks between visits, the interval is too long or the fault has grown. Where the line is still clean at each visit, the interval may be safe to stretch. Owners of shops, cafes and mixed-use buildings can arrange this kind of program through commercial plumbing maintenance providers.
Repeat jetting has costs that do not show up on the invoice. Each visit puts water pressure on a pipe that is already damaged, and roots keep growing back through the same opening. At some stage a repair costs less than the run of visits, and the camera footage helps you see when that stage arrives. Emergency visits add more again, since a line that blocks at night is billed at after-hours rates. Weighing those repeat bills against a single repair price helps you decide when to stop clearing and start fixing. Our sewer line repair cost page lists prices for lining, patching and replacing private sewer pipes.
Who Pays: Your Pipes, the Junction and the Public Main
Sydney Water says owners are responsible for wastewater pipes from their property up to where they connect to its network. It owns the junction where your pipe joins its main, but the joint between your pipe and that junction is the owner's to maintain. Roots growing in at that joint are the owner's to clear, even where the connection lies outside the property boundary. If a licensed plumber finds the blockage in Sydney Water's pipes, you can claim reasonable out-of-pocket costs you have paid. The plumber must report it to Sydney Water and give you a job number for the claim.
Signs that the public main is blocked include an overflow beyond your boundary or neighbours with the same problem. Report those overflows on 13 20 90 at any hour, and find fault and claim details on the Sydney Water website. In the Hunter, Hunter Water asks owners to check the sewer shaft and call 1300 657 000 if it is full or overflowing. Outside those areas, local councils run water and sewer in many towns, so check your council's website for its sewer fault number.
Sewer service diagrams help you and the plumber see where your private pipes run before work starts. These diagrams are sold online through Sydney Water's Tap in service, which says most are available almost immediately. The diagram shows the private wastewater pipes on the property, but work that was never inspected may be missing from it. Treat it as a guide, and confirm the route on camera before anyone digs or lines a pipe. Owners outside Sydney can ask Hunter Water or their council what drainage records they hold for the property.
Rentals, Strata Buildings and Shared Lines
In a rented home, drain clearing is a repair for the landlord or agent to arrange, and a tenant who caused the blockage may have to pay. The NSW urgent repairs list includes a blocked or broken toilet system, so a sewer blockage that stops the toilet working counts as urgent. If the landlord or agent cannot be reached, a tenant can arrange a licensed tradesperson and be repaid up to $1,000. The landlord or agent must repay the tenant within 14 days of receiving written notice and receipts. Landlords planning ongoing drain care can combine it with other jobs through rental property maintenance services.
In strata schemes, responsibility depends on where the pipe runs and what it serves. The NSW common property memorandum assigns the owners corporation, the body of all lot owners, a floor drain or sewer in common property (shared areas) and pipes inside common walls, floors and ceilings. Lot owners are listed for the S bend, the curved pipe under a sink, laundry sink or basin, and for pipes past the lot's stopcock, or shut-off valve, that serve only that lot. Jetting a sewer or floor drain in common property is therefore arranged by the owners corporation. Tell the strata manager before booking a plumber yourself for a shared line. For how owners corporations handle plumbing repairs, see our strata and body corporate plumbing page.
Disputes about who pays can go to a tribunal when talking does not settle them. The NSW Civil and Administrative Tribunal hears residential tenancy and strata scheme disputes, and details are on the NCAT website. Keep the camera footage, invoices and photos, since they show where the blockage was and what caused it. Records of this kind help when a cost has to be split between a lot owner and the owners corporation.
Licences and Paperwork for Drain Cleaning
In NSW, you need a licence or certificate for any plumbing, draining or gasfitting work, whatever the cost. Licences are issued under the Home Building Act 1989, and the regulator is Building Commission NSW, on 13 27 00. Check the plumber's name or licence number on the NSW Government's Verify licence register before work starts. Confirm that the licence covers draining, since cleaning a sewer drain is draining work. Checking takes a few minutes and protects you if something goes wrong later.
When plumbing or drainage work is completed, the licensed plumber gives a Certificate of Compliance, a signed record that the work meets the rules, to the person who arranged it. Larger jobs also need a Notice of Work, an advance notice to the regulator, lodged before they begin, while emergency and minor works are exempt from that step. In Sydney, the Illawarra, the Blue Mountains, Newcastle and the Hunter, these documents go through the MyInspections Gateway online portal, and local regulators handle other areas. Before work starts, find out whether your job needs a certificate, and get a copy if it does. For any repair after the clean, such as a new section or a lined pipe, the certificate is part of the job. Keep it with the invoice and the camera footage.
Residential work over $5,000 including GST needs a written contract in NSW. The deposit is capped at 10 percent, and warranties set by law run for 6 years for major defects and 2 years for other defects. Jetting visits on their own sit well below that amount, but a repair after the clean can exceed it. Make sure the contract is signed before paying any deposit on a lining or replacement job.
Getting Comparable Jetting Quotes
Clear details in your request help plumbers price the job before they arrive. Describe which fixtures are slow, whether sewage has come up outside, and how long the problem has been building. Mention the age of the home, any trees near the drain line and whether the drain has been jetted before. Photos of the overflow gully, inspection openings and any wet patches in the yard help too. If you have a sewer service diagram, attach it so the plumber can see the route of the line.
Details to Send With Your Quote Request
Which fixtures are slow or blocked, and whether the toilet, shower or outdoor gully has overflowed.
The age of the home, the drain material if known, and any trees growing within about 6 metres of the line.
Where the inspection openings, overflow gully and stormwater pits are, with a photo of each.
Any past jetting, camera reports or repairs, and the sewer service diagram if you have one.
Plumbers can only price what they know about, so a fuller request gives you closer quotes.
Have each plumber price the same scope so the quotes can be compared fairly. A complete quote lists the call-out fee, the jetting, any root cutting, camera work and whether a written report is included. It should also say what happens if the jetter cannot clear the line, and whether you pay for an attempt that fails. Prices quoted by the hour need an estimate of hours, or you cannot compare them with a fixed price.
To find local plumbers across the Sydney metro area, use our page on how to hire a plumber in Sydney. Owners further north can request quotes through our page for plumbers in Newcastle and the Hunter. Compare at least two quotes for larger jobs, and look closely at a quote far below the others. Low quotes may leave out the camera, the clean-up or the extra charge for after-hours work. Clarify those points in writing before you accept.
What to Look Out For in Hydro Jetting Quotes
Be wary of a plumber who wants to jet an old drain without a camera check, especially in a home built before the late 1980s. Unclear pricing is another warning sign, such as an hourly rate with no estimate of hours or a jetting price with no line length. Pressure to sign up for a long maintenance plan on the first visit, before any footage has been shown, deserves a second opinion. So does advice to reline or dig up the whole line when the footage shows a single fault. Treat any request for full payment upfront on a large repair with caution, given the 10 percent deposit cap. Stop if the licence number does not match the name on the Verify register.
A plumber worth hiring explains what is likely in the pipe, names the access point and says whether jetting is safe for the pipe material. Ask how the pipe will be protected if the camera shows a weak section. The quote lists each item with its own price, and the footage is offered as part of the job. After the work, the plumber shows you the clear line running and hands over the paperwork without being asked.
Other Plumbing Jobs to Book With a Jetting Visit
Plumbers on site with a jetter and camera can look at related problems in the same visit, which saves a second call-out. Gully grates, missing inspection caps and cracked pit lids are small items that can be fixed while the plumber is there. Downpipes connected to the sewer can be quoted for correction once the camera has found them. Leaking or corroded supply pipes carry clean water rather than waste, so they are handled through water pipe replacement instead of drain clearing. Properties on septic systems need a different approach, and our septic tank services page describes the tank and its disposal area, the ground where treated water drains away. For other work around the house, see the main jobs we can help you price in our plumbing services in NSW hub.
Plan bigger works in a sensible order to avoid paying twice. Clear the line and film it first, then decide on lining or replacement, and restore paving and gardens last. Where a section must be dug up, excavation contractors use free Before You Dig Australia plans to avoid hitting other buried pipes and cables. Keep every report together so the next plumber starts from what is already known.
Drain Cleaning Plumbers in Every NSW Region
We connect homeowners, landlords and strata managers with licensed plumbers throughout New South Wales for drain jetting, root cutting and camera checks. Post your job once and compare quotes from plumbers who work in your area.
▶ Sydney Inner City 18 areas
▶ Greater Sydney 25 areas
Western Sydney
South Western Sydney
Northern Sydney
The Hills District
Inner West
St George
▶ Sydney Coastal 23 areas
Northern Beaches
Eastern Suburbs
Harbour Suburbs
Sutherland Shire
▶ Hunter & Central Coast 19 areas
Central Coast
Hunter Valley
Port Stephens
▶ Illawarra & South Coast 18 areas
Illawarra
Shoalhaven
Sapphire Coast
▶ North Coast 19 areas
Mid North Coast
Coffs Coast
Northern Rivers
▶ Blue Mountains & Highlands 17 areas
Blue Mountains
Southern Highlands
▶ Regional NSW 21 areas
Central West
Riverina
New England
Far West
Hydro Jetting and Drain Cleaning FAQs
Is hydro jetting safe for old clay sewer pipes?
How long does a drain stay clear after jetting?
Can I use a pressure washer drain hose on my sewer?
Why did the plumber want to film the drain before jetting?
What does hydro jetting cost in NSW in 2027?
Will jetting remove tree roots for good?
Who pays when the blockage is in the junction or the main?
Is a blocked drain an urgent repair in a NSW rental?
Can stormwater drains be jetted the same way as sewer lines?
What paperwork should I keep after a jetting visit?
Trades That Help Keep Drains Running
Related Services
For Trades & Contractors - NSW
Plumbers with jetting and drain camera gear can browse current work on the NSW job leads board, along with plumber jobs in NSW and emergency plumber jobs.
Ready to Clear a Stubborn Drain?
Post your job and compare quotes from licensed NSW plumbers for drain jetting, root cutting and camera inspections.
Get Free Plumber QuotesAbout This Guide
This guide is general information only, and NSW rules, utility policies, product details and prices can change. Confirm requirements with your water and sewer provider, Building Commission NSW, your owners corporation where relevant, and a licensed plumber before work starts.
Looking for more services across New South Wales? View all available trade services.
Reviewed by The Quote Yard Editorial Team
How The Quote Yard Works
We connect you with independent local tradies and service providers, we don't perform any trade work ourselves. Tradies provide their own quotes directly to you. Always confirm licensing, insurance, and scope of work before engaging any provider.