Pipes Banging in the Walls?

Tell us which taps or appliances set off the noise and when it started, and we'll connect you with licensed plumbers near you.

Get Free Plumber Quotes

Typical Costs (2027 Estimates)

Call-out fee (business hours)$80-$150
Plumber hourly rate (business hours)$90-$180/hr
Pressure check and diagnosis visit$80-$200
Pressure limiting valve, fitted$200-$600
Tap washer or jumper repair (per tap)$60-$250
Toilet cistern inlet valve$120-$200
Concealed pipe repair$400-$1,500+

These figures are 2027 estimates for NSW homes. Arrestors, pipe clipping and wall or tile repairs are priced per job.

Water Hammer and Noisy Pipe Repair Services NSW - Get Local Quotes

Water hammer is the bang or thud in the walls when a tap, toilet or appliance shuts off the water suddenly. Moving water has weight, so stopping it at once sends a shock wave back along the pipe. Loose pipes then knock against timber framing, and the noise can travel through the whole house. Triggers include fast-closing mixer taps, washing machine and dishwasher valves, high mains pressure and pipes that have lost their clips. Worn tap parts and air left in the pipes after water main repairs can also cause knocking and rattling. Before the visit, note which tap, toilet or appliance sets off the bang and whether it follows hot or cold water. A licensed plumber finds the cause by listening, testing the pressure and checking which fixture sets off the noise. Fixes range from a new tap washer or a small shock absorber called an arrestor to a pressure limiting valve, which lowers the incoming pressure, at the meter. Securing loose pipes in the roof space or under the floor can quiet a home with only a few new clips. On 2027 estimates, a pressure check visit costs about $80 to $200, and a pressure limiting valve fitted about $200 to $600. Arrestors and pipe clipping are priced on quote, because the time to reach the pipes varies so much. Strata owners and renters should report the noise early, since shared pipes and landlord repairs follow their own rules. Keep the invoice, the pressure reading and any Certificate of Compliance, the plumber's signed record, with your home records once the work is finished.

Noisy Pipe Plumbers Across NSW

Licensed plumbers trace banging, knocking and rattling pipes in houses, apartments and rentals across Greater Sydney, the Hunter, the Central Coast, the Illawarra and regional NSW. Describe the noise once and we can put you in touch with up to three local plumbers for quotes you can compare.

Get Free Quotes

At a Glance - Water Hammer and Noisy Pipe Repairs in NSW (2027 Estimates)

Job 2027 Estimate (NSW) Suits Disruption Paperwork to Keep
Pressure check and diagnosis visit $80-$200 Banging in several rooms or after mains work Under an hour, water briefly off Written pressure reading
Pressure limiting valve, supplied and fitted $200-$600 Pressure above 500 kPa with all taps shut Water off for part of the visit Invoice and valve details
Tap washer or jumper repair $60-$250 a tap Chattering or knocking from one older tap One tap out of use briefly Tax invoice
Ceramic disc cartridge replacement $100-$300 Mixer taps that shudder or shut unevenly One tap out of use briefly Tax invoice
Toilet cistern inlet or outlet valve $120-$200 Knocks or hums as the cistern refills Toilet out of use briefly Tax invoice
Exposed pipe repair $150-$300 A loose or damaged pipe within reach Hours, one area Tax invoice
Concealed pipe repair $400-$1,500+ Pipes inside walls or under floors Wall or floor opened Certificate of Compliance where required
Arrestor fitting or pipe re-clipping Priced on quote One noisy fixture or loose lengths of pipe Depends on access Invoice showing positions

Cost Depth: What Moves a Noisy Pipe Repair Price

Finding the cause takes much of the time. A pressure check visit is estimated at $80 to $200, and a pressure limiting valve supplied and fitted costs $200 to $600 where pressure with all taps shut is above 500 kPa.

How easily the plumber can reach the pipes drives the rest of the bill. A repair on an exposed pipe is estimated at $150 to $300, a concealed pipe repair at $400 to $1,500 or more, and lifting and relaying tiles at $200 to $600.

All figures are 2027 estimates for NSW. Arrestors and pipe clipping are priced on quote, and regional travel can add to the final amount.

What Water Hammer Is and Why Pipes Bang

Water moving through a pipe is heavy, and it cannot stop instantly without pushing back on something. When a valve slams shut, the moving water hits it and a pressure wave runs back along the pipe toward the meter. Hunter Water describes hammering as the knocking or vibrating noise that sometimes comes from water pipes. That shock travels along the pipe and can make it bang, rattle or shudder against whatever it touches. The louder the bang, the faster the water was flowing or the more suddenly it was stopped.

Several things can make the problem worse in an ordinary NSW home. High mains pressure means the water moves faster, so each sudden stop delivers a bigger jolt. Pipes that are poorly fixed in place can swing and strike the frame, turning a small surge into a loud knock. Valves that close in a fraction of a second, such as those inside washing machines, leave the water no time to slow down. Long straight runs of pipe also carry more moving water, which gives the wave more force when it arrives. Each of these can be checked and fixed on its own, which keeps the repair targeted and the bill smaller.

Not every pipe noise is water hammer, and the cause decides the repair. One heavy bang at the moment water stops points toward hammer, while a steady hum or whistle while water runs has other causes. Rattling that comes and goes with the tap open can mean a loose pipe or a worn part vibrating in the flow. Spluttering taps and milky water after nearby works suggest air in the pipes rather than a fault in the home. A licensed plumber can check for each of these causes, and you can find one through our plumbing services page.

Bangs, Knocks, Rattles and Hums: Matching the Noise to a Cause

Writing down what you hear, and when, saves the plumber time and saves you labour charges. Note whether the noise comes when water starts, while it runs or the moment it stops. Record which tap, toilet or appliance sets it off, and whether it happens on hot water, cold water or both. Mention if the noise started after renovations, new appliances or water main work in your street. Record the sound on your phone and name the fixture, as that gives the plumber a clear starting point.

One sharp bang when a mixer tap is flicked off is the classic sign of a fast-closing valve. Repeated knocks a few seconds apart while a washing machine fills point toward the machine's inlet valves opening and shutting. Thumps late at night with nobody using water may come from a toilet cistern refilling, or a garden watering system switching between the separate areas it waters in turn. Chattering as a tap is slowly closed can come from a loose washer or worn part inside that tap.

Humming or buzzing while water runs needs a different check, starting with the valves and the pressure. Noise that starts only when a pump switches on or off brings the pump and its controls into the check. Gurgling from sinks and drains is a separate problem in the waste pipes, not the water supply. For drain noises and smells, book a plumber for sewer smell and drain odour repairs instead. Tell the plumber about every noise you have noticed, even ones that seem unrelated, since a home can have two faults at once.

Noisy Pipe Repair Prices for 2027

Water hammer repairs are priced mostly on time, because finding the cause can take longer than fixing it. The figures below are 2027 estimates for NSW, drawn from our published plumbing price ranges. Arrestors, which are small shock absorbers fitted to a pipe, and pipe clipping have no published price range, so plumbers quote them per job. Those quotes are built from the call-out fee, the hourly rate and the parts, plus the time spent reaching the pipes. For general plumbing rates, see our plumber pricing guide for NSW. Regional jobs can carry extra travel time, so ask whether it is charged separately or built into the call-out fee.

Job 2027 Estimate (NSW) What Drives the Price
Call-out fee (business hours) $80 to $150 Travel distance and the time of the booking
Plumber labour (business hours) $90 to $180 an hour Time to trace the noise and reach the pipes
After-hours labour $150 to $250 an hour Evenings, weekends and urgent visits
Pressure check and diagnosis visit $80 to $200 Number of fixtures tested and access to the meter
Pressure limiting valve, supplied and fitted $200 to $600 Valve size, setting and pipe work at the meter
Tap washer or jumper repair (per tap) $60 to $250 Tap type and parts
Ceramic disc cartridge replacement $100 to $300 Mixer brand and part availability
Toilet cistern inlet or outlet valve $120 to $200 Cistern model, parts included
Isolation valve replacement $100 to $220 Valve type and the age of the pipe
Washing machine hose replacement $80 to $150 Hose length and tap condition
Exposed pipe repair $150 to $300 Pipe material and fitting type
Concealed pipe repair $400 to $1,500 or more Wall or floor access and reinstatement
Tile removal and reinstatement for access $200 to $600 Tile type and spare tiles
Arrestor fitting, pipe re-clipping, appliance noise valve Priced on quote No published price range; parts, number of fittings and access

Exposed pipes under a timber floor or in a roof space cost less to reach than pipes buried in a brick wall. Simple repairs on an exposed pipe are estimated at $150 to $300, while a repair on a concealed pipe runs from $400 to $1,500 or more. Where tiles must come off to reach a tap body, lifting and relaying them adds an estimated $200 to $600. After-hours work is estimated at $150 to $250 an hour, so book a weekday visit when the noise is a nuisance rather than an emergency. Listing every small fault in the house when you book lets the plumber deal with them in one trip.

How a Noisy Pipe Quote Adds Up

A typical visit starts with a call-out fee of $80 to $150 and labour at $90 to $180 an hour, with one hour as a common minimum charge.

Parts are added on top, such as a pressure limiting valve to lower the incoming pressure, a tap cartridge or pipe clips. Plumbers can add a margin of 10 to 30 percent to the trade price of parts, so ask for the parts to be itemised.

All figures here are 2027 estimates for New South Wales homes. Wall openings, tiling and plaster repairs are extra.

Simple Checks Before a Plumber Visits

Some checks cost nothing and help pinpoint the source. Closing taps slowly is a free first test, since Hunter Water lists taps turned off quickly as a cause of pressure fluctuations. If the bang goes away when you close a tap gently, the tap's closing speed is part of the problem. Try running each fixture in turn while someone listens near the wall or under the house. Check whether the noise happens at the same time each day, which can point to a watering timer or appliance cycle.

Water mains work in your street can leave air trapped in household pipes. Hunter Water advises running the outside tap closest to the water meter to clear air, then turning other taps on slowly, one at a time. It also suggests leaving taps running until any milky or discoloured water clears. Hold off on washing clothes or running the dishwasher until the water runs clear.

Stop at checks like these and leave the repairs themselves to a licensed plumber. Sydney Water's guidance limits householders to changing a tap washer, and it sends every other plumbing job to a licensed plumber. Fitting arrestors, adjusting valves and refixing pipes all count as plumbing work under that advice. Do not tighten or bend pipes in the wall cavity yourself, as a cracked joint can leak unseen for weeks. Shut the water off at the meter and call a plumber if the noise comes with a leak, damp patches or a drop in pressure.

When the noise began after mains work in the street, contact the water supplier for your area first. In Sydney, the Illawarra and the Blue Mountains, Sydney Water takes fault reports on 13 20 90. Hunter Water supplies Newcastle and the lower Hunter, and its advice on clearing air from the pipes applies there. In many regional towns, the local council runs the water supply and takes the calls. Broken Hill is served by Essential Water, a division of Essential Energy. Your water bill names the supplier, so keep a recent bill handy when you call.

How a Plumber Tracks Down the Noise

Tracing water hammer is a process of elimination, and a methodical plumber works through the house one fixture at a time. The first step is to listen while each tap is opened and closed, then while each appliance runs a short cycle. Next comes a pressure reading with a gauge, so the plumber knows whether high pressure is one of the causes. The plumber then checks the meter area for a pressure limiting valve and notes its condition and setting. With the source narrowed down, they look at the pipes nearest that fixture, in the roof space or under the floor where possible. Finally, the tap or valve itself is opened up if its internal parts are suspected.

Easy access to the roof space and the area under the floor speeds the job, so clear a path to the roof hatch and any underfloor door. Move stored boxes away from the laundry and kitchen walls if pipes run behind them. Pets should be kept away from open hatches and work areas. For noise that only happens at night or during a watering cycle, ask whether the plumber can run the timer manually during the visit.

Some causes show up only under certain conditions, and a single visit may not catch them. Noise from an appliance may only appear partway through a long wash or rinse cycle. Keep your notes and recordings going after the visit if the plumber cannot reproduce the sound. One more short visit at the right time of day can then confirm the cause. Check whether a return visit is charged as a new call-out or as time on the original job.

Fast-Closing Taps and Appliance Valves

Modern single lever mixer taps can stop the flow with one flick of the handle. Caleffi, an Italian valve maker, lists single lever mixing taps, solenoid valves and ball valves, which shut with a quarter turn, among the devices that create these pressure surges. A solenoid valve is an electrically operated valve that opens and shuts the water at the press of a button or a signal. Quarter-turn taps, which go from fully open to closed in a quarter turn, can shut faster than older screw-down taps. None of these taps is faulty, but a home with high pressure or loose pipes may react loudly to them.

Washing machines, dishwashers and fridges with ice makers use valves that can shut the water off in an instant. Fisher & Paykel makes front loader and top loader washing machines, so give the plumber the brand and model if the noise comes during a wash. Banging during a wash, and not when you use a tap, points toward the machine's inlet valves. RMC makes the QuietWash valve, which it says is designed to reduce water hammer in washing machines and dishwashers. RMC states that this valve is fitted between the tap and the machine's inlet hose. Plumbers can fit one during washing machine installation or as a separate job.

Sensor taps and garden watering systems also use electrically controlled valves. Galvin Engineering makes touch-free sensor tapware, which starts and stops the flow without anyone touching a handle. Holman makes solenoid valves and controllers for automatic garden watering, which switch the water between zones on a timer. If thumps happen when your watering system switches areas, mention them when booking irrigation and garden watering system servicing.

Fridges with filtered water or ice makers have their own valve and small supply line behind the cabinet. Knocking each time the ice maker refills can mean that valve is causing a surge in the line. Plumbers who handle fridge water lines can check the connection and the line's fixing. Dishwashers are checked in the same way, with the plumber watching the supply line as the machine starts a cycle. Connections for those machines are part of every dishwasher installation job.

Worn Tap Parts and Sticking Jumper Valves

Older screw-down taps close by pressing a rubber washer onto a seat inside the tap body. The washer sits on a small part called a jumper valve, which moves up and down as the handle turns. Hunter Water lists a sticking jumper valve in a tap as one cause of hammering in pipes. Loose or worn washers can flutter in the flowing water and send a chattering noise along the pipe. Replacing the washer or jumper is a standard leaking tap repair, and it can stop a drip at the same time.

Mixer taps use a cartridge instead of a washer, and a worn cartridge can also vibrate or shut unevenly. Replacing a tap washer or jumper is estimated at $60 to $250 a tap for 2027, including parts. A ceramic disc cartridge, the sealed insert that controls flow in a mixer, is estimated at $100 to $300 to replace. Methven makes shower heads and tapware, and replacement parts should match the maker's model number. Bring the model name or a photo of the tap so the plumber can bring the right cartridge.

Toilet cisterns are another source of noise, because the inlet valve shuts off as the tank fills. If a knock comes at the moment a cistern stops filling, the plumber will check that valve first. Replacing a cistern inlet or outlet valve is estimated at $120 to $200 including parts. Caroma makes dual flush toilets, so note the brand and model of each toilet when booking a cistern repair. Running or noisy toilets can be booked as toilet repairs in the same visit. Have the plumber check every cistern in the house if more than one refills noisily.

High Mains Pressure and the 500 kPa Limit

Water pressure is measured in kilopascals, written kPa, the unit shown on a plumber's pressure gauge. AS/NZS 3500.1, the Australian standard for water supply plumbing, sets a maximum static pressure of 500 kPa at any outlet inside a building, other than fire service outlets. Static pressure is the pressure in the pipes when every tap is shut and nothing is flowing. Where the mains pressure is above that limit, a pressure limiting valve is needed to bring it down. That valve is fitted near the water meter and holds the pressure inside the home at a set level.

High pressure makes every sudden stop more violent, so it is one of the first things a plumber tests. Taps turned off quickly cause pressure changes, according to Hunter Water, and higher mains pressure makes those changes larger. Sydney Water says water pressure that is too high can cause pipes to break and leaks to form. RMC makes pressure limiting valves set to let through a fixed 350, 500 or 600 kPa, and the plumber picks the setting that suits the home.

To check pressure, the plumber fits a gauge to a tap, such as the garden tap nearest the meter, with all other taps closed. A pressure check visit is estimated at $80 to $200, and a pressure limiting valve supplied and fitted at $200 to $600 for 2027. Sydney Water notes that existing pressure reducing valves, another name for these valves, may need upgrading in some areas, so homes with one should still be tested. Weak showers and slow taps are the opposite problem, which plumbers handle as low water pressure repairs. Ask for the pressure reading in writing, both before and after any valve is fitted or adjusted.

Three Readings Worth Asking For

Ask the plumber to record the static pressure at the meter with every tap closed. Ask for a second reading inside the home once any pressure limiting valve has been fitted or adjusted.

A third reading taken after the noisy fixture is used again shows whether the fix has worked. Keep these numbers with the invoice, as they help any future plumber.

The 500 kPa figure is the maximum static pressure at outlets inside a building under AS/NZS 3500.1.

How a Water Hammer Arrestor Absorbs the Shock

A water hammer arrestor is a small cylinder fitted to the pipe near the valve that causes the surge. Inside, a piston separates the water in the pipe from a sealed pocket of air. When the pressure wave arrives, it pushes the piston against the air, which compresses and soaks up the shock. RMC's instructions for the Sioux Chief Hydra-Rester, an arrestor it supplies in Australia, describe this piston and air design. Ask the plumber which type is being fitted and whether its maker lists any servicing needs.

Some older homes have air chambers, which are short capped lengths of pipe that hold a pocket of air above a tap. Air chambers only work while they still hold air, and a plumber can check whether they do. Once a chamber fills with water, it gives no protection against the shock. Sealed piston arrestors keep their air pocket separate from the water, so they do not fill up the same way.

Arrestors do not lower the mains pressure, so they suit homes where the pressure is already within the limit. Where the pressure is too high, the limiting valve comes first, and an arrestor may then deal with a single noisy fixture. Caleffi recommends its arrester for single fittings, such as under a washbasin, or small groups such as one bathroom. For long pipe runs or larger buildings, the plumber may suggest a different fix sized for the whole system. Get the plumber to explain why an arrestor, a valve change or both suits your home.

Choosing between the fixes is easier with the test results in hand. If the pressure reading is above 500 kPa, a pressure limiting valve is needed to meet the standard, whatever else is done. With the pressure within the limit and one appliance causing the noise, an arrestor or appliance valve near that fixture is the likely target. If the noise travels along a pipe run and the pipe can be seen moving, extra clips and spacers to hold it still come first. When several causes combine, the plumber may suggest doing the cheapest fix first and testing again before spending more. That staged approach keeps you from paying for parts the house turns out not to need.

Where an Arrestor Should Be Fitted

Position matters, because an arrestor works best close to the valve that creates the shock. RMC's instructions say that where one fixture causes the problem, the arrestor goes upstream of it, on the supply side, within one metre. For a branch line up to six metres long serving several fixtures, they place it at the end, between the last two fixtures. A branch line is the smaller pipe that leaves the main supply to feed a room or a group of taps. The same instructions call for the arrestor to sit at right angles to the pipe on a T fitting, a T-shaped joint in the pipe.

Washing machine taps and kitchen sink valves are easy places to fit an arrestor, since the pipes are within reach. During a new kitchen sink installation, an arrestor can go on the supply under the sink while the cabinet is still open. Taps fed by pipes buried in tiled walls are harder, and the plumber may fit the arrestor in the roof space or under the floor. RMC's instructions also say to check for leaks before the arrestor is hidden behind a wall or panel. Find out where each arrestor will sit, so it can be located again if the noise ever returns. Keeping a quick sketch or photo with the invoice helps the next plumber find it.

Arrestors come in several sizes, and the plumber chooses one to suit the pipe size and the fixtures it protects. The Hydra-Rester instructions list AS 5200.007, the product specification for water hammer arrestors, among their approvals. Plumbing products in drinking water pipes must carry WaterMark certification, a scheme run by the Australian Building Codes Board. Check the WaterMark details on the packaging before buying an arrestor online. Any plumber who refuses to install an uncertified part is protecting your home and your insurance position.

Loose Pipes, Clips and Brackets

Some banging noises come from the pipe moving, not from the water alone. Securing loose pipes so they cannot strike the frame can make a big difference to the noise. Pipes are held to the frame with clips or brackets, and clips can work loose, break or never have been fitted. Under the floor, pipes can sag between supports and slap against the floor framing when the water stops. In the roof space, pipes resting loose on ceiling timbers can rattle against timber or each other. Reaching the worst spot may mean lifting a floorboard or removing a ceiling access panel.

Clips with a rubber lining help keep vibration out of the building frame. Walraven, a pipe support maker, says rubber absorbs vibration, so less noise passes through the bracket into the structure. Filling a gap between a pipe and a wall stud, the upright timber in the frame, or adding a clip where it knocks, can quiet a pipe without other changes. Copper and plastic pipes have different clipping needs, and each maker sets its own spacing and fixing rules. REHAU makes the RAUTITAN system of PE-Xa pipes, a type of flexible plastic pipe, and fittings for hot and cold water in homes.

Iplex makes Poliplex PE100 polyethylene pipe for water services, and the pipe from the meter to the house may be a plastic type like this. Whatever the pipe material, ask which maker's guide the plumber follows for clip type and spacing. Re-clipping is priced on quote, because the time depends on access to the roof space, subfloor or wall cavity. Request a note of how many clips will be added and where, so the work can be checked afterwards.

Noise From the Hot Water System and Pumps

Hot water pipes carry the same moving water as cold pipes, so they can hammer as well. Tell the plumber whether the noise follows hot taps, cold taps or both, because that narrows the search. Rheem makes electric storage, gas storage, heat pump and continuous flow water heaters, and each has its own valves and connections. RMC describes its pressure limiting valves as ideal for installation with high pressure storage water heaters. Weak or uneven hot water flow is a separate fault, handled through repairs for hot water pressure issues.

Rinnai makes gas continuous flow hot water units, which heat water as it passes through instead of storing it. Dux makes heat pump and solar hot water systems as well as storage and continuous flow models. In areas where Sydney Water changes the water pressure, it notes that some instantaneous, or continuous flow, hot water systems may need upgrading. Noise inside the heater itself is a matter for the maker's service agent or a plumber who repairs that brand. Faults inside the unit can be booked through our hot water system repairs service.

Homes on rainwater tanks or with a booster pump have a pump that starts and stops as taps open and close. Grundfos makes the SCALA2 booster pump, which it describes as the quietest pressure booster on the market. Onga makes household pressure pumps and rainwater pumps for homes that draw water from a tank. Noise that lines up with the pump starting or stopping needs the pump, its controls and its mounting checked together. Plumbers who handle rainwater tank plumbing can check the pump connections and any valve that tops the tank up from the mains.

Why Repeated Hammering Should Not Be Ignored

One bang now and then may seem harmless, but each surge puts strain on the pipes and joints. Valves, tap parts and appliance hoses all sit in the path of each pressure wave. Pipes that move with every surge can rub against framing, and joints that flex again and again can loosen over time. Call a licensed plumber promptly if the noise is getting louder, pipes are visibly shaking, or more than one area is affected. Leaks, moisture or corrosion near the noisy pipes are further reasons to book a visit soon. Noting when the banging first started helps the plumber judge how long the pipes have been under strain.

Damp patches on walls or ceilings near a noisy pipe can mean a joint has started to leak. Hidden leaks can be traced through water leak detection before any wall is opened. A water bill that rises with no change in use is another sign worth raising with the plumber. Braided hoses, the flexible metal-covered hoses under sinks and toilets, carry the same water and should be checked while the plumber is there. Old or rusty hoses can be swapped through our flexible hose replacement service in the same visit.

If a pipe does burst, turn the water off at the meter straight away and call a plumber. Under NSW rental rules, a burst water service, meaning the supply pipe, or a serious leak counts as an urgent repair. For after-hours help, an emergency plumber can make the pipe safe. Once the urgent repair is done, ask the plumber to look for the cause of the noise so the next surge does not repeat the damage.

Noise That Starts After Renovations or New Appliances

Noise that starts after a renovation or new fittings can mean something was installed or fixed incorrectly. New mixer taps can close faster than the screw-down taps they replaced, which may expose loose pipes that were quiet before. New washing machines and dishwashers may also have stronger or faster valves than the old ones. Pipes moved during a renovation may have been refixed with fewer clips, or left resting against new framing. Contact the plumber who did the work first, because the fix may fall under their workmanship warranty.

Plumbers who install new taps should consider the pressure before fitting them. Choosing new tapware with the pressure in mind is part of good tap and mixer installation work. Outdoor taps raise extra questions about backflow, where dirty water is drawn back into the supply, and hose fittings, which a plumber handling outdoor tap installation can answer. The installing plumber should run each new tap and appliance while listening for hammer before leaving.

Major renovations are a good time to deal with old noisy pipes, because walls and floors are already open. Galvanised steel pipes in older homes can corrode inside and may be replaced as part of a renovation. Whole runs of failing pipe can be swapped through water pipe replacement while the walls are open. A full repipe of a standard three-bedroom house is estimated at $3,000 to $15,000 for 2027, depending on access and materials. Fitting arrestors and clips before the walls close costs far less than opening them again later.

When planning a renovation, tell the plumber about any past banging so it can be handled at rough-in. Rough-in is the stage when new pipes go into walls and floors before the plasterboard and tiles are fixed. Request clips wherever pipes pass through framing, using clips that suit the pipe material. Arrestors near a new laundry sink installation or kitchen appliance point can be fitted at this stage while the pipes are open. Tapware instructions can list a working pressure range, so compare it with the pressure reading before choosing new taps. Photos of the pipe runs taken before the walls close show where each arrestor and clip sits.

Reaching Pipes Inside Walls in Older Homes

Pipes buried in brick walls or behind tiles are the hardest to quiet, because they cannot be reached without opening the surface. The plumber will first try every option from the roof space, the subfloor and the nearest access panel. Where a wall must be opened, ask who repairs the plaster or tiles and whether that cost is in the quote. Patching after the plumber leaves is a job for a plasterer, such as those listed under plastering and gyprock repairs. Keep spare tiles from the original job, as matching old tiles later can be difficult.

The national Asbestos Safety and Eradication Agency says a home built or renovated before 1990 might contain asbestos. Its asbestos safety advice is to check for asbestos before repairs start, and to treat material as asbestos if you cannot confirm either way. Tell the plumber the age of the home so they can plan the access safely. Testing can be arranged through asbestos testing and inspection before the wall is opened. Never break into old fibre cement sheeting to track down a noise yourself.

Buyers who hear banging pipes during an open home can ask for a plumbing check before contracts are exchanged. Booking a pre-purchase plumbing inspection can add a pressure reading and a look at visible pipes and clips. High readings or loose pipes found that way can then be priced before the sale goes ahead. Sellers can also fix the noise first, as a quiet water system makes a better impression on buyers.

Noisy Pipes in Apartments and Strata Buildings

In apartments, the pipe making the noise may not belong to the owner who hears it. Under the NSW Government's common property memorandum, pipes within common property walls, floors or ceilings are the owners corporation's responsibility. The owners corporation is the legal body made up of every owner in the strata scheme, and common property is the shared parts of the building. The memorandum also gives the owners corporation the main stopcock, the shut-off valve, to each unit. Pipes past a unit's stopcock that serve only that unit, and that do not run inside a common property wall, are the owner's job.

Taps and their fittings belong to the lot owner under the same memorandum, so a noisy mixer inside a unit is the owner's to fix. Hammer from shared risers, the vertical pipes that feed each floor, or from building pressure valves is a matter for the strata manager and the owners corporation. Report the noise in writing, with the time it happens and the unit it seems to come from. By-laws, the rules each building adopts, may set conditions on work hours, water shut-offs and access to other units. Owners corporations can book shared work through strata and body corporate plumbing services.

Larger buildings can have booster pumps or pressure reducing valves that serve several floors at once. Sydney Water says property owners are responsible for fire protection systems and other pressure-dependent equipment on their property. Check with the strata manager who services any shared pumps or valves, and when they were last checked. If several units hear banging at the same times, the shared equipment is a logical place to start. Joint reports signed by several owners give the strata manager a clearer picture than separate complaints. Keep a copy of every report and the strata manager's reply with your own records.

Noise from a neighbour's washing machine or tap can travel through shared walls and pipes. Talking to the neighbour first can show whether the noise lines up with their appliance use. If a fix is needed on their side, the cost falls to that owner unless the pipe is common property. Where the source is unclear, the owners corporation can arrange one plumber to inspect the shared pipes.

Renters and Landlords

Banging pipes on their own are not on the NSW list of urgent repairs. Urgent repairs do include a burst water service or serious leak, and a failure of the water supply. When neither landlord nor agent can be reached for an urgent repair, the tenant can arrange it and be repaid up to $1,000. The landlord or agent must repay the tenant within 14 days of the tenant's notice. The full list of urgent repairs is published on the NSW Government website.

For non-urgent repairs, the landlord or agent should arrange for the work to be done. Tenants should report hammering in writing, noting which fixture causes it and when it started. Reporting early matters, because a loose joint left to leak may later become an urgent repair. Tenants may need to give the plumber access, and the usual notice periods for entry apply. Landlords managing several properties can bundle the job into rental property maintenance visits.

Landlords replacing a noisy tap may want the new one to meet the water efficiency rules for rentals. Kitchen sink and bathroom basin taps need a maximum flow of 9 litres per minute where the landlord wants to pass on water usage charges. A plumber offering rental water efficiency compliance checks can confirm the taps, showers and toilets meet the rules. The plumber can note the flow rating of any new tap on the invoice.

Licences, Paperwork and Product Approvals

All plumbing work in NSW needs a licence, whatever it costs. Licences are issued under the Home Building Act 1989, and Building Commission NSW regulates plumbers on 13 27 00. Before booking, search the plumber's name or licence number on the NSW Government's Verify licence register. Sydney Water treats replacing a tap washer as the only job for a capable householder and sends all other plumbing work to licensed plumbers. Fitting valves, arrestors and clips to water pipes counts as licensed work under that advice.

Before starting work, the plumber lodges a Notice of Work, a form telling the regulator what plumbing work is planned. Emergency work and minor works, such as replacing tapware, are exempt from that notice. At the end of all plumbing and drainage work, the plumber completes a Certificate of Compliance, a signed record that the work meets the rules. A copy goes to the person who arranged the work, such as the owner or builder. The national plumbing rules are set out in the Plumbing Code of Australia and the AS/NZS 3500 series published by Standards Australia.

Jobs over $5,000 including GST need a written contract in NSW. The deposit on those contracts is capped at 10 percent of the price. Major defects carry a six-year warranty set by law, and other defects a two-year one. Keep the invoice, the certificate and any product warranty cards together with your home records.

Getting Useful Quotes for a Noisy Pipe Problem

Water hammer can be hard to price over the phone, so plumbers may quote a diagnosis visit first. Ask whether the first hour of labour is included in the call-out fee, and what happens if the cause is found quickly. Once the cause is known, ask for a fixed price for the repair, with parts listed separately. Compare quotes for the same work, such as pressure testing, one arrestor and re-clipping a set length of pipe. One request through our plumbing services page can bring up to three quotes from licensed plumbers near you.

What to Include When Asking for Quotes

Your suburb, the age of the home and whether it is a house, townhouse or apartment. A recording of the noise and the name of each fixture that sets it off.

Whether the noise follows hot taps, cold taps or appliances, and when it started. Any recent water main work, renovations or new appliances, and whether you have a pressure limiting valve or booster pump.

Plumbers who receive the same facts can price the same work, so the figures line up side by side.

A good quote names the cause the plumber suspects and the test they will use to confirm it. It should list the pressure reading if one has been taken, and the proposed setting of any new pressure limiting valve. For arrestors, it should state the number, size and position of each one. For pipe clipping, it should say where the plumber will work and how the area will be accessed. The plumber's licence number should appear on the quote, together with the call-out fee and the hourly rate charged for anything extra. Compare each figure with the 2027 estimates in our price table before you say yes.

What to Look Out For in Water Hammer Repair Quotes

Be wary of a plumber who recommends a full repipe for a noise without testing the pressure or checking the clips. Repiping is a large job, and cheaper fixes should be ruled out first unless the old pipes are failing for other reasons. Removing a pressure limiting valve to improve flow, without first measuring the incoming pressure, may leave the home above 500 kPa. Quotes that offer an arrestor on every tap without explaining why may include parts you do not need. Cheap arrestors sold online without WaterMark certification are a poor buy, since a licensed plumber may refuse to install them.

Watch for quotes with a single line for fixing the noise, with no detail on the cause or the parts. Low prices that leave out wall repairs or tiling can end up costing more than a fuller quote. Treat a demand for a big upfront cash payment with caution, as deposits on NSW contracts above $5,000 are limited to 10 percent. Extra work found behind a wall should be priced and approved in writing before the plumber goes ahead.

After the Repair: Checking the Noise Has Gone

Before the plumber leaves, run every tap, toilet and appliance that made a noise and listen together. Ask for the final pressure reading and the location of any new valve, arrestor or clip. Over the next week, listen for the noise at the times it used to happen, such as during a wash cycle or overnight watering. Check under sinks and near the meter for any drips at new joints. Call the plumber back promptly if the noise returns, as a second fault may have been hidden by the first.

Booking other small plumbing jobs for the same visit means paying the call-out fee only once. Dripping taps, running toilets and worn fittings can be fixed through bathroom and kitchen fixture repairs. Weak pipes found during the check may need burst pipe repairs before they fail. A planned garbage disposal installation can also be booked for the same visit, since the plumber will already be working under the sink. Itemised prices for each extra job let you pick the ones that fit the budget and leave the rest for later.

Noisy Pipe Plumbers in Every NSW Region

We connect homeowners, landlords and strata owners with licensed plumbers throughout New South Wales for water hammer, banging pipes, pressure limiting valves and loose pipe repairs. Post your job once and compare quotes from plumbers who work in your area.

▶ Sydney Inner City 18 areas
Sydney CBD Surry Hills Darlinghurst Potts Point Paddington Redfern Newtown Glebe Balmain Pyrmont Ultimo Chippendale Alexandria Waterloo Zetland Erskineville Rozelle Leichhardt
▶ Greater Sydney 25 areas

Western Sydney

Parramatta Penrith Blacktown Mount Druitt Seven Hills Wetherill Park Auburn Fairfield Cabramatta St Marys

South Western Sydney

Liverpool Campbelltown Bankstown Revesby

Northern Sydney

Hornsby Chatswood Epping Macquarie Park Eastwood

The Hills District

Castle Hill Baulkham Hills

Inner West

Ryde Strathfield Burwood

St George

Hurstville Kogarah
▶ Sydney Coastal 23 areas

Northern Beaches

Manly Dee Why Curl Curl Freshwater Brookvale Collaroy Narrabeen Mona Vale Newport Avalon Palm Beach

Eastern Suburbs

Bondi Tamarama Bronte Coogee Maroubra Randwick

Harbour Suburbs

Double Bay Rose Bay Watsons Bay

Sutherland Shire

Cronulla Miranda Sutherland
▶ Hunter & Central Coast 19 areas

Central Coast

Gosford Terrigal Wyong The Entrance Tuggerah Erina Woy Woy

Hunter Valley

Newcastle Maitland Lake Macquarie Charlestown Belmont Raymond Terrace Cessnock Singleton Muswellbrook

Port Stephens

Nelson Bay Salamander Bay Shoal Bay
▶ Illawarra & South Coast 18 areas

Illawarra

Wollongong Shellharbour Kiama Dapto Corrimal Thirroul Gerringong

Shoalhaven

Nowra Berry Ulladulla Huskisson Vincentia

Sapphire Coast

Batemans Bay Moruya Narooma Bega Merimbula Eden
▶ North Coast 19 areas

Mid North Coast

Port Macquarie Forster Taree Kempsey Laurieton

Coffs Coast

Coffs Harbour Bellingen Sawtell Grafton Yamba

Northern Rivers

Byron Bay Tweed Heads Ballina Lismore Bangalow Lennox Head Brunswick Heads Mullumbimby
▶ Blue Mountains & Highlands 17 areas

Blue Mountains

Katoomba Leura Wentworth Falls Blackheath Springwood Hazelbrook Glenbrook Faulconbridge Lawson Blaxland Lithgow

Southern Highlands

Bowral Moss Vale Mittagong Bundanoon Robertson Berrima
▶ Regional NSW 21 areas

Central West

Orange Bathurst Dubbo Mudgee Parkes Forbes Cowra Young

Riverina

Wagga Wagga Albury Griffith Leeton Goulburn Queanbeyan

New England

Tamworth Armidale Inverell Moree Narrabri

Far West

Broken Hill Cobar

Water Hammer and Noisy Pipe FAQs

Is water hammer dangerous for my pipes?
Repeated water hammer puts strain on pipes, joints and valves each time it happens. Valves, tap parts and appliance hoses all sit in the path of each pressure wave. Pipes that move with each surge can rub on framing, and joints that flex can loosen and start to leak. Call a licensed plumber if the noise gets louder, pipes shake or several areas are affected. Fixing the cause early costs less than repairing a leak inside a wall.
Why do my pipes bang when the washing machine fills?
Washing machines open and shut their inlet valves quickly during a cycle, stopping the water in an instant. Each sudden stop sends a pressure wave back along the pipe to the laundry taps. High mains pressure or loose pipes behind the wall make the bang louder. RMC makes the QuietWash valve, which it says is designed to reduce water hammer in washing machines and dishwashers. A licensed plumber can fit one between the tap and the hose, check the pressure and secure any loose pipes.
What is the maximum water pressure allowed inside a NSW home?
AS/NZS 3500.1 sets a maximum static pressure of 500 kPa at any outlet inside a building, other than fire service outlets. Static pressure is the reading with every tap closed and no water flowing. Where mains pressure is higher, a pressure limiting valve is needed at the property to bring it down. A plumber measures this with a gauge, such as the garden tap nearest the meter. A pressure check visit is estimated at $80 to $200 for 2027.
What does a water hammer arrestor do?
An arrestor is a small cylinder fitted to a pipe near the valve that causes the surge. Inside, a piston pushes against a sealed pocket of air, which compresses and absorbs the shock. RMC's instructions for one arrestor place it within one metre upstream of a single noisy fixture. On a branch line up to six metres long, they place it at the end, between the last two fixtures. Arrestors are priced on quote, because the number needed and the access to the pipes vary.
Can I fix water hammer myself?
You can turn taps off more slowly, use soft close settings on appliances and note which fixture causes the noise. After water main works, Hunter Water advises running the outside tap nearest the meter to clear air from the pipes. Under Sydney Water's advice, a householder may replace a tap washer, and anything beyond that is work for a licensed plumber. Fitting arrestors, pressure valves or pipe clips is licensed work in NSW. Do not bend or tighten pipes inside walls yourself, as you may crack a joint.
Why did my pipes start banging after water main repairs in my street?
Mains repairs can let air into the pipes, and trapped air can cause spluttering taps and knocking. Hunter Water lists air in the pipes after maintenance work as a cause of hammering. It advises running the outside tap closest to the meter, then turning other taps on slowly, one at a time. Leave taps running until any milky or discoloured water clears before using the washing machine. If the noise stays after the air has cleared, ask a licensed plumber to check the pressure and pipes.
Who pays to fix noisy pipes in a strata apartment?
The NSW common property memorandum makes the owners corporation responsible for pipes within common property walls, floors or ceilings. It also gives the owners corporation the main stopcock to each unit. Pipes past a unit's stopcock that serve only that unit and are not inside a common property wall belong to the unit owner. Taps and their fittings also belong to the unit owner. Report the noise to the strata manager in writing so the right party can arrange the repair.
Is banging pipes an urgent repair in a rental home?
Banging pipes alone are not on the NSW list of urgent repairs. A burst water service or a serious leak is urgent, and so is a failure of the water supply. For non-urgent problems, the landlord or agent should arrange the repair once the tenant reports it. Tenants should report the noise in writing, since a joint that later leaks may become urgent. If an urgent repair is needed and no one can be reached, the tenant can arrange it and claim back up to $1,000.
How much does it cost to fix water hammer in NSW in 2027?
A pressure check visit is estimated at $80 to $200, and a pressure limiting valve supplied and fitted at $200 to $600. A tap washer or jumper repair runs about $60 to $250 a tap, and a toilet cistern inlet valve about $120 to $200. Arrestors and pipe clipping have no published price range and are priced on quote. Call-out fees of $80 to $150 and labour of $90 to $180 an hour apply in business hours. Opening walls or tiles to reach pipes adds to the final cost.
Will a pressure limiting valve stop my pipes banging?
A pressure limiting valve lowers the pressure inside the home, which softens each sudden stop of the water. Higher pressure means faster water and a harder jolt when it stops. Where the static pressure is above 500 kPa, the valve is needed anyway to meet AS/NZS 3500.1. If the pressure is already within the limit, the noise is more likely from loose pipes, a fast valve or a worn tap part. Ask the plumber to measure the pressure first so you pay only for the fix that suits the cause.

Trades That Help Quiet Noisy Pipes

For Trades & Contractors - NSW

Plumbers who trace water hammer and fix noisy pipes can browse current work on the NSW job leads board, along with plumber jobs in NSW and emergency plumber jobs.

Ready to Stop the Banging?

Post your job and compare quotes from licensed NSW plumbers for pressure checks, arrestors and loose pipe repairs.

Get Free Plumber Quotes

About This Guide

This guide is general information only, and NSW rules, product details and prices can change. Confirm requirements with Building Commission NSW, your water supplier, your owners corporation where relevant, and a licensed plumber before work starts.

Reviewed by The Quote Yard Editorial Team

Published 18 November 2026 ·

How The Quote Yard Works

We connect you with independent local tradies and service providers, we don't perform any trade work ourselves. Tradies provide their own quotes directly to you. Always confirm licensing, insurance, and scope of work before engaging any provider.

All NSW tradies are required to hold appropriate licences. Verify at NSW Fair Trading.
Prices are 2027 estimates for New South Wales and exclude wall, tile and plaster repairs and regional travel. Water hammer arrestors and pipe re-clipping are quoted per job.
Need work done? Get free quotes. Post a Job – It's Free